similar to: Issue with Grandstream ATA 496.

Hi Everybody, I'm experiencing this kind of issue. One ASTERISK 1.2.17 is connected to a Bristuffed HFC single ISDN channel card. Everything seems to work but sometimes the third party caller when listening to MOH listens some "SSHHHHH!" instead of MOH, this is not continuos, MOH plays ok for, say, 20 seconds then the sound and then another 30 seconds of good MOH. We have some

Hi everybody I have installed a TrixBox with Asterisk 1.2.14 and relative upgreaded software. I Bristuffed it with last version of bristuff to use a Hemlet PCI ISDN CARD in a normal Italian EUROISDN installation. The * works fine except for the ISDN CARD. It is always Channel D down, but if a Call comes in, it works perfectly for some time, both inbound and outbound. It prompts Channel D UP!

Hi, Bristuff works great with HFC card... your compilation problem may come from your kernel configuration... You should check this doc, at least, for the redhat config : http://www.automated.it/guidetoasterisk.htm Then, installation of Bristuff works like as charm ! Bye David Masure -----Message d'origine----- De : vdasilva [mailto:aquamoon@wol.co.za] Envoy? : mardi 28 juin 2005 09:01

Hello I have asterisk running in Red Hat 9 with a cheap HFC card on i4l. I have choppy sound problems sometimes, and echo problems often. I am using a 2 port Grandstream ATA, Grandstream BT and a Grandstream GPX-2000 I read that changing to BriStuff will fix the echo problems, but have also read other users say that the only way they solved the echo/choppy sound problems was using a Fritz ISDN

Hi everybody, I'm in a middle of a Asterisk learning period. I am at a very good point except I'm not able to use VoiceMailMain. This Is my simple dialplan regarding VoiceMail ;Number that the IP Phones dial to access voice mail exten => 22999,1,VoiceMailMain (s${CALLERIDNUM}) exten => 22999,2,Wait(3) exten => 22999,3,Hangup Why do I get Forbidden 403 and one console display

Hi everybody, I have corrected this line in extensions.conf by stripping spaces off and now it executes: exten => 22999,1,VoiceMailMain(s${CALLERIDNUM}) when it runs, the mail box number is asked and password too. I expected no question were made, because I inserted CALLERIDNUMBER and s in front of box number. Anybody knows why? Thank to you all, very kind members of this list! Ciao Mauro

Hi dear group members, I have finally an Asterisk box working, capable of receiving and making calls. I have this issue while calling mobiles from our SIP softphones: -------------------------- linux*CLI> -- Executing NoOp("SIP/2000-6850", "3487024125") in new stack -- Executing Dial("SIP/2000-6850", "ZAP/g1/3487024125") in new stack -- Called

Hi everybody I'm trying to make Asterisk 1.2.1 run under VMWARE and Suse 9.2. I use ZTDUMMY module for timing and ZTTEST gets an average precision of 98,4 %. Is there any way to improve it? Best regards Mauro Zanin -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060117/945d544a/attachment.htm

Hi people, I would like to read your suggestions as to where the issue might be. ATA286=Grandstream Budgetone ATA 286 in SIP mode. One Lan Port and one FXS port. TDM04B= 4 FXO signal fxls There is a 8FXO-to-SIP unit in this scenario that works perfectly so i will not make mention of it. PSTN----VOIPprovider---Internet---ATA286------tdm04b---Asterisk1.2.-13 Asterisk is being used as a meetme

I'm using bristuffed Asterisk with ISDN/ZAPHFC I have VERY ugly (outgoing) sound through ISDN/HFC if echocancel=yes in zapata.conf, but without echocancel I have bad (incoming) echo Through PSTN/FXO sound is ok with or without echocancel. I tried other echo cancellers (in zconfig.h) two times: ECHO_CAN_KB1 (this was default) ECHO_CAN_MARK2 ECHO_CAN_MG2 after any change I compiled (make

hello, I have a asterisk box (Slackware 9.1.0, Linux 2.4.31) connected to a Ericsson Businessphone PBX on the internal S0 bus with HFC-S card and zaphfc driver - point2point mode -. --------- | TELCO | | BRI | --------- | | PBX external S0 -------- | PBX | -------- | PBX internal P2P S0 NT Mode | | HFC-S Card P2P TE Mode

Hi everybody, I'm strugling between two devices: the both TE but one was set up as a TN. I have no current on that interface. I have tried to find some circuit over the net to power the connection, both commercial and home made. Can anybody give some hint? Ciao Mauro

Hi everybody, I have this issue: I need to automatically park an incoming call, play a welcome prompt and then connect to some extension but under extension user's command. I was thinking to use a small database to comunicate between asterisk and the main application. Has anybody had this kind of experience? Best regards Mauro

Hello, I have a problem with the Bristuffed version of Asterisk. I have tried Bristuff-0.3.0-pre-1m,n,o,p (Asterisk 1.2.6 to 1.2.7.1) but they all have the same problem it seems: The setup: A machine with a single hfc-s PCI BRI adapter running Gentoo 2.6.15. Asterisk 1.2.0 (BRIstuffed-0.3.0-PRE-1) installed and working perfectly. Grandstream gxp-2000 as a SIP phone, and a normal mobile

I hva ean HFC-S card in a box that I'm trying to get to work with bristuffed Asterisk 1.0.3. The box is an Athlon64 running a RHEL rebuild with a plain vanilla 2.6.10 kernel. I tried both APIC and NOAPIC mode. The installation went ok and does give output that seems correct SPAN 1: CCS/ AMI Buil-out: 399-533 feet (DSX-1) 2 channels and one D-channel Even though I've configured * to

Hi folks, I've already searched the mailing list but no one else seems to have my same problem. I'm using Asterisk with the following configuration: Fedora Core 4 (but I also tried Fedora 3) 1 Digium TE110P 1 TDM40B 1 HFC-S 'Cologne' bristuff 0.2.0-RC8o (zaptel 1.0.9.2) I compiled right, I can load kernel modules but when I try to unload wcte11xp module (the one

I'm using a Grandstream IP phone to call someone through our asterisk pbx. The PBX is running "Asterisk 1.0.3-BRIstuffed-0.2.0-RC3" and uses 2x ZAP-HFC cards. When I call someone, if the call isn't answered and then I hang up, I get "487" coming up on the grandstream phone. If I pick up the receiver again and then hang up, the PBX starts calling me back and when I

Hello * users I've problems with sound quality on zaphfc Asterisk works fine good sound quality. If I do "make load" in the bristuf.xx zaphfc dir then sound quality drops directly. Even if I don't load the chan_zap in the modules.conf I use this config on more (even old 400Mhz machines) and works correctly. Looks like an hardware problem but I can't find it. I don't

hi, I am on fax-to-email system, basically taken from http://www.voip-info.org/wiki-Asterisk+Fax+to+email well, it seems that asterisk causes some problems so that it is impossible to send any fax. I.e. when I try to send a fax to asterisk (rxfax application): normalFax--->FXS(TDM400P)--->Asterisk(RxFax) it breakes up the trasmission at the beginning of sending page. The code given by

I have a problem with Asterisk-bristuffed using a zaphfc card. I am located in the Netherlands, so I have an ISDN line from KPN. When I start Asterisk, and plug in the ISDN line, everything works perfectly for about 5 minutes. And then the ISDN line is down for 1 minute, and after that minute, the line comes back up and works for another 5 minutes. Every time the line goes down I get the error