similar to: Sangoma A101 on Freebsd 6.2

hi folks, Im pretty sure this has been covered before but I just wasnt able to find any answer. Im having troubles with the call pickup feature, is just not working for me. whenever I press *8 or 200 or anyother. nothing happens and sometimes I also get" nothing to pickup". I have read this might be a bug although I havent found any patch for it. does anyone have any ideas? Im using

I upgraded from Tormenta2 to Sangoma A101. I followed the instructions, and installation was successful. zttool, ztcfg, all show card is installed properly. I copied the parameters from my old working zaptel.conf, zapata.conf and zapata-auto.conf. Verified on Sangoma website that these files are correct. Also configured wanpipe1.conf. But doing all this didn't start the PRI channels. It says

Hi All Just a quick check on the best way to ensure multiple cards/devices load in the correct order. Asterisk 1.8 with Sangoma A101 had no problems until we introduced an Astribank. root at pabx377:/etc/asterisk# dahdi_hardware -v usb:001/004 xpp_usb+ e4e4:1162 Astribank-modular FPGA-firmware LABEL=[usb:X1060395] CONNECTOR=@usb-0000:00:1d.7-3 XBUS-00/XPD-00:

Hiya all, I have had no end of trouble trying to get my A101 E1 card working on a new asterisk installation. The sangoma tech people have ignored my emails about this. All the installation of wanpipe seems to go ok, and zaptel. it all installed compiled and does all the wanpipe hwprobe exactly as documented. Asterisk compiled ok, but when I run it give me Jun 27 11:12:18 ERROR[10528]:

We are having an occasional one w-way audio problem that occurs about every 25 - 30 calls on a system configured as follows: Asterisk 1.2.12.1 Sangoma A101 w/wanpipe beta9 Polycom 500s w 1.5.3 This happens only on inbound calls from the PRI. The external caller can hear our customer answer and say hello, however, our customer cannot here their caller. Typically, the caller calls right back

Im trying to install and configure sangoma ... every thing is OK but when type the command "wanrouter start" the following error apears: wan Driver not found. Thanks for any help

I just got a brand new A101 and am trying to install it in my test Asterisk box. The install went without a hitch. I followed the directions on the Sangoma Wiki: Wanpipe Asterisk Install http://sangoma.editme.com/wanpipe-linux-asterisk-install Wanpipe for Asterisk Configuration http://sangoma.editme.com/wanpipe-asterisk-configure It went perfect, no problems and Asterisk came up fine. I downed

I am having a problem trying to get a Sangoma A101 to work with Unicall. I have installed the sangoma drivers and everything seems to be well but when I try to run ztcfg I get the following error: CAS signalling on span 1 conflicts with HDLC with FCS check on channel 16. Here is my /etc/zaptel.conf # MFC/R2 normalmente no usa CRC4 span=1,0,0,cas,hdb3 cas=1-15:1101 dchan=16 cas=17-31:1101

Uys, Steve Underwood I just got a Sangoma A101 card and Im using unicall 0.0.3.pre9 for R2MFC, I get the far and local end unblocked but as soon as I try to make a call I get dialing and then protocol failure.. Do you guys know if there are any issues with sangoma and unicall? Anybody has an a101 card working with unicall and r2mfc? Are you out there Steve? :)

Any benefit on getting the PCI Express version? Bill -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070222/62f79910/attachment.htm

Hi Folks, I'm have Asterisk version 1.2.1 with a A101 PRI card. I'm working with the CLEC to bring up the PRI and inbound calls are hanging up at his end after a few seconds. I ran PRI debug but it only gives me minimal insight. " Ext: 1 Cause: Unknown (16), class = Normal Event (1)" He ran a trace and the only difference he is seeing is a "ISDN interface explicitly

Hi, I have A101DE Sangoma Card( http://www.sangoma.com/products/hardware_products/digital_voice_and_data_networking/a101.html ) lspci shows as 03:04.0 Network controller: Sangoma Technologies Corp. A200/Remora FXO/FXS Analog AFT card [root at asterisk ~]# lspci -vvv -s 03:04.0 03:04.0 Network controller: Sangoma Technologies Corp. A200/Remora FXO/FXS Analog AFT card Subsystem: Unknown device

Hi, I am considering A101/102/104 cards for my asterisk installations. Has any of you used these or any Sangoma cards in such environment? Any thoughts? How do they stack up against Digium cards? Any input would be greatly appreciated. robert

Anyone using a Sangoma A102 with a Dell 750? We are looking at going this route but needed some input. I really only need a Single T1 port, but this server doesn't have a PCI-X port, which the A101 apparently requires? Thoughts, Suggestions? K

Hello All, I have a setup of ABE on rPath linux,Sangoma A101D, and a T-1 line (Not PRI) which is all happily coexisting and all lights are green. The T-1 comes in from the world into a "Shark Box" which splits the T into 384K data and 6 channels voice. The data side is working great. The voice side, not so great. It was originally broken out to 6 pots line and Verizon came back

Hi ! We curently have a centos 5 / asterisk 1.4 server that we have some DTMF problems with. It has a Sangoma A104d card and only port one is used to connect to the PSTN. Port 2 is conencted via a cross-over cable to a RAS for modem access and port 3 is connected for data communication via PPP. Now, I want to freshen this setup to something newer. So I installed a Scientific Linux 6 server,

Hello, We have an Asterisk 1.0.9 machine with a Sangoma A101 card fitted, it is connected to a Telstra OnRamp E1 in Melbourne, Australia. The problem we are experiencing is extreme echo and clicking noises. These are only audible to the calling party, e.g. the person calling in from the PSTN to Asterisk via the E1, the person on the SIP handset cannot hear any echo or clicking, only the

I have installed Asterisk on a CentOS4 box and then installed Asterisk from CVS. I installed a Sangoma A101 and connected it to a Adtran 600 using a T1 Crossover cable. The 600 has 12 x FXS, 12 x FXO interfaces. I ran through the wanpipe install instructions and configured it, now I can run [root@altpbx asterisk]# wanrouter hwprobe ------------------------------- | Wanpipe Hardware Probe Info

Does anyone know if the Sangoma A101 supports DS4 and/or RBS ! Shame on me for not knowing the answer, but I don't, and I can't find any mention of it on Sangoma's website. Cory Andrews Purchasing Manager ++++++++++++++++++ VOIPSupply.com A Division of b2 Technologies 454 Sonwil Drive Buffalo, NY 14225 ++++++++++++++++++++ direct - 716.250.3402 mobile - 716.907.4054 email -

Hi, So, SMACK is a software verifier based around LLVM, and you can find more info (PDF, title, abstract) about our recent publication here: http://soarlab.org/2014/05/smack-decoupling-source-language-details-from-verifier-implementations/ I would appreciate if you could add it to your list of LLVM-based publications. Thanks! Best, -- Zvonimir -- http://zvonimir.info http://soarlab.org/