similar to: PRI DCHAN Errors

So I might have a bit of a more narrow question from my earlier one. Previous, I had been wondering what would cause a phone dialing into a DID that connects to the asterisk box to get a fast busy. I've noticed the following message: chan_zap.c: Ring requested on unconfigured channel 0/1 span 2 Any idea what would give me this error? And would this cause a fast busy? Thanks again everyone

Hi guys, I've been installing and configuring a TE110p card. The compile and install went very well. I'm using this on FC4 and I compile with linux26 as well checked I on the udev configs. zttool and ztcfg both indicate that the card is ready. But when I try to "load chan_zap.so" then I get the following Unable to load module chan_zap.so Jan 5 21:43:33 ERROR[6808]:

Hi All; Suddenly the zaptel channel look like stop working and it is giving me this error when I do zap restart: [May 24 19:30:21] ERROR[2772]: chan_zap.c:7219 mkintf: Unable to open channel 1: Device or resource busy here = 0, tmp->channel = 1, channel = 1 [May 24 19:30:21] ERROR[2772]: chan_zap.c:10582 build_channels: Unable to register channel '1,2' To what it could be related?

Hello, I have an E100P, and in the zaptel.conf I have: span=1,1,0,ccs,hdb4,crc4,yellow fxsks=1-10 the light on the card is green( BTW what do all those states of the card that zttool reports YELLO, RED, BLUE ..., is there a doc for zttool?, or for the card?) in the asterisks` zapata.conf I have: [channels] context=default switchtype=euroisdn signalling=fxs_ks usecallerid=yes hidecallerid=no

Hi guys, I'm hoping I've made a silly mistake here, but I've been staring at the screen for the past few hours and I can't work it out. I upgraded to 1.2.16 recently, and am having problems with zaptel. The card is detected, I get a reasonable output from ztcfg -vv, and zttool shows the installed module (TDM400) with one FXS module. But when I start asterisk, I get

Hi all. chan_zap not compiling, yes yes I know this sounds trivial but here me out... This morning I decided to upgrade to Asterisk 1.4.2 and Zaptel 1.4.1. I successfully installed zaptel 1.4.1 and the card is picked up and correctly configured. ztcfg shows the following: [root@zion root]# ztcfg -vv Zaptel Version: 1.4.1 Echo Canceller: MG2 Configuration ====================== Channel

Hi, I just compiled and installed Asterisk-1.4.2 along with zaptel-1.4.1 and libpri-1.4.0 on a Debian machine with a TDM400P card. Everything goes ok but when I try to make a call through the ZAP channel get an error message about NO ZAP CHANNEL AVAILABLE. Ztcfg and zttool show the card correctly installed. When I tried to use the debug command ZAP SHOW, it was not present in the CLI. My

Hello I just installed a TE110P in a Dell Poweredge 750 (rackmount), which is connected via crossover T1 cable to a adit 600. Anyway, I've encountered an array of errors, which I believe I have narrowed down to the 22 IRQ misses I encounter on zttool. I've noticed that the te110p and the usb device share an IRQ. Could that be the source of my woes? Would disabling the usb device in the

<P>hi Everyone,</P> <P>We are configuring an ISDN PRI E1 with an E100P card, when you load the drivers, and starts the asterisk, cards also starts fine, givin following output,</P> <P>*CLI> <BR>&nbsp; == D-Channel on span 1 up<BR>&nbsp;&nbsp;&nbsp; -- B-channel 1 successfully restarted on span 1<BR>&nbsp;&nbsp;&nbsp; --

Hi! I have the chance to play with a couple of E400P cards, each installed in a IBM e330 XSeries servers (2 x 1GHz P-III CPU 2 Gb RAM, 36Gb SCSI HDD with RH8.0 2.4.18-smp kernel), and I'm trying to test/benchmark this e330/E400P combo generating calls thru /var/spool/asterisk/outgoing One e400P if doing the carrier work making calls and the other just receives the calls: Server#1

We have install a DS3 with 28 DS1's we have an Adtran MUX breaking out the DS1's, we are trying to setup the system with 2 dchannels for each 4 DS1's. Everything looks fine when modprobe zaptel and wct4xxp and ztcfg -vvvvvv but when I asterisk asterisk it says: Aug 10 16:33:32 ERROR[8954]: chan_zap.c:6750 mkintf: Channel 24 is reserved for D-channel. Aug 10 16:33:32 ERROR[8954]:

I've been beating my head a bit against the 1.0.6 Debian builds of Asterisk, using an E100P (E1, single span) board. In machines I've built in the past (back in 1.0.0 days), config I'm using and that card and 1.0.0 driver combo worked fine. ztcfg reports no problems: SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) 31 channels configured. And zttool sees the card, and

Hello list , I?m putting to work a new asterisk box. I?m running * 1.0.3 with (one ) Wildcard TDM ( 2FXS* 2FXO) and (one) E-100P. Both boards are working well. ztcfg don?t show me any error. zttool list both cards as "OK" But when i run asterisk on verbose mode i get those errors : [chan_zap.so] => (Zapata Telephony) == Parsing '/etc/asterisk/zapata.conf': Found --

Hi ! I'm trying to configurate my first asterisk system. My test plant has an E100P Card and a 4 FXS TDM 400P card. I've an E1 configured for 15 channels. Telco says that crc4 is configurated so my zaptel.conf is: loadzone = it defaultzone=it span=1,0,0,ccs,hdb3,crc4 bchan=1-15 dchan=16 unused=17-31 fxoks=32-35 zttool shows no alarms. I've also tried changing the timing

Calling out on PSTN over a TDM400P seems to generate a Red Alarm - whatever that is. I have another extension on the PSTN, and I can dial out over that. zttool shows no alarms. asterisk*CLI> zap show status Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO Wildcard TDM400P REV I Board 1 OK 0 0 0 CAS Unk YEL 0 db

Hi, I came back from a quiet weekend today and found my E400P box to have gone astray. Asterisk is loaded from inittab, and started crashing and reloading a couple of thousands of times, each time notifying my monitoring service :-P I remember there would be issues on old cvs stuff since the crash at digium so I made a clean checkout just now. Here is what happens when I load manually:

Hi, I am having some problems mentioned below, the box is in production live environment with traffic around 30 - 100 calls. I am running T/E410P in a Dual P4 xeon with HT disabled. I am using zaptel 0.9.0 and asterisk stable 1 release. There is no gui, just mysql, perl (small script) and asterisk. System runs very smoothly if the calls are around 40-50 and comes one by one , however sometimes

Hi, I hope someone can help me with this.... Asterisk 1.0.6 Zaptel 1.0.6 Libpri 1.0.6, 1 Digium E100P card installed Panasonic TDA200 firmware v2.0.6 E1 Card Firmware 1.0.2 System is located in Australia, so as technologies go, I believe it is twist on the euro standard for the E1 signalling. Here is the situation. The TDA E1 card is set in cross over mode and I am using a functional

how can I fix this just started ...... Jul 14 14:32:35 NOTICE[4983]: chan_zap.c:6223 ss_thread: Got event 18 (Ring Begin)... == Starting Zap/1-1 at bell,s,1 failed so falling back to exten 's' == Starting Zap/1-1 at bell,s,1 still failed so falling back to context 'default' Jul 14 14:32:35 WARNING[4983]: pbx.c:2377 __ast_pbx_run: Channel 'Zap/1-1' sent into invalid

hi i'm trying to configure a TE205P on asterisk@home i've edited /etc/sysconfig/zaptel adding this line: MODULES="$MODULES wct2xxp" now, when the system is loading, i can see that the wct2xxp module is loaded correctly but if i try the command: /usr/local/sbin/genzaptelconf i get: STOPPING ASTERISK STOPPING FOP SERVER Generating '/etc/zaptel.conf' Generating