similar to: Quad BRI cards

Hi, I plan to setup an * Server with a TE10P PRI card as E1 and a BN4S0 4 Port BRI card in one box. I tried it first with the bristuff drivers from Junghanns. The BRI card worked fine alone, but as soon as I load the zaptel driver for the TE110P the BRI card says, that the port is down. So I tried it with mISDN. But it seems that this stuff is still unstable (Asterisk refuses to start at first

BUG/SYMPTOMS: 1.Under certain circumstances, octoBRI (and most likely quadBRI) ISDN cards (Junghanns/CologneChip) severely distort certain ISDN payload. 2.Although these claims relate to the bristuff patch, the problem might not be limited to bristuff and in fact be rather asterisk/zaptel/libpri related. 3.Signal distortion is limited to the use of the CVS version of the Bristuff patch for

I'm using Asterisk 1.09 with bristuff 0.2.0-RC8n, one BRI line and a Sipura SPA-2000. I have a HP LaserJet 3330mfp all-in-one. I can receive faxes but not send them. The faxes start whistling to each other but the transmission is stopped with a "communication error" To receive a fax I have this in my dialplan: exten => 0000000000,1,Ringing exten => 0000000000,2,zapEC(off)

Hi list! I am running CentOS 4.1 x86_64 on an Athlon64. The box was installed only yesterday. Yesterday I was still able to compil stuff, yesterday even the tiniest and simplest programs fail to compile always with internal compiler error: Segmentation fault. For example: make -C /usr/src/linux-2.6 SUBDIRS=/tmp/bristuff-0.2.0-RC8n/qozap ZAP=-I/tmp/bristuff-0.2.0-RC8n/zaptel-1.0.9 modules

Good Evening, The company I work for is attempting to connect an Cisco ISDN Router to an OpenVOX B200P BRI Card so that we can get it to dial out across an existing ISDN PRI Line also installed in the Asterisk PBX Everything has compiled successfully and the BRI card has been detected when mISDN is started: # misdnportinfo Port 1: NT-mode BRI S/T interface port (for phones) -> Interface

On Friday, March 31, 2006 3:52 PM Chris Earle wrote: > I'm wondering if I should be using zapHFC with my Junghanns card > instead of qozap? Why would you want to do that? Sorry if I missed the start of the problem but qozap is what you want to use with your Junghanns card (at least if you want to stay with zaptel/libpri). > Everyone always mentions zaphfc -- mostly I >

Have you got termination set correctly? I have a B410P working with 2 x NT and 2 x TE ports successfully. I had to turn the 100ohm termination on on the NT ports (even though I have them set as PTP in mISDN.conf). HTH -->> -----Original Message----- -->> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- -->> bounces at lists.digium.com] On

Hi, I guess I'd need to run Beronet quad and octo bri cards under bristuff to get zaptel features (echo canceling, timing source).... Am I right or could I achieve this also with chan_misdn - their native driver ? Running bristuff on Beronet cards is unsupported. Has anyone succesfully run Beronet quad BRI cards under bristuff recently ? Do they work ? Regards, Rob.

> Appreciate the replies everyone -- really > > I'm wondering if I should be using zapHFC with my Junghanns card instead > of > qozap? Everyone always mentions zaphfc -- mostly I guessed because they > are > using a zaphfc-compatible card ----- but *maybe* I should try that instead > of qozap??? > > And yep -- totally know about the module load order thing and

I'm having trouble installing Beronet BN4S0 card. I have downloaded instructions from here http://www.beronet.com/download/card_installation_guide.pdf And when I download install-misdn-mqueue[1].tar.gz I untar it and execute "make" and "make install". This is the output that I get. [root@nbirma1 install-misdn-mqueue]# make install make -C app_bundle make[1]: Entering

Hi, I'm currently deciding on what card to pruchase for octo/quad BRI card to use with Asterisk on EuroISDN lines. I'm aware of at least two options (Junghanns or Beronet), but don't know how stable and well supported they are. Which ones are better supported ? Any experiences? Any advice ? How tos ? What would you buy ? Thanks in advance, Regards, Rob.

Hi, i use an BN4S0 with misdn an asterisk on Linux 2.6.9. The hfcmulti module is loaded with option: type=0x04 protocol=0x2,0x2,0x22,0x2 layermask=0xf,0xf,0xf,0xf and the fourth port is connected to an ISDN PTMP (MSN) port. Call to #72 from S0 (BN port 4) are not accepted from asterisk but why ? Can anyone give me a hint ?? misdn debug messages follows: lib: NEW_CR Ind with l3id:80001

We have here a TandBerg "videoconferencing system" connected in asterisk with a Beronet card BN4S0 (4 BRI ports). I`m trying to make a videoconferece (video + audio) with this Tandberg to another Tandberg using the ISDN channels through the BN4S0 BRI Card. But, i'm only obtaining audio calls, the video not appears. When i try to make a 64K calls (data calls), the call does not

Hi list, Has anyone been able to get ISDN-BRI support to work reliably on Asterisk 1.4? If so, I'd love to know how you did it (hardware, distro, kernel, modules, versions, config files). I've tried to get it to work on a Debian etch system with an HFC-PCI card and the zaptel package (v1.4.7, also from xorcom.com), but with no luck: all three channels that are created when the

Hello, The harddisk of my etch/bristuffed asterisk1.2 box finally died. I moved the cheap (1397:2bd0) HFC-S card to a squeeze host (i686) and built dahdi modules 2.3.0.1 using m-a. After zaptel->dahdi and asterisk 1.2->1.6 config adaptations, everything seems ok, except for the BRI side, unable to bring layers 1/2 up. Asterisk reports: chan_dahdi.c:12393 dahdi_pri_error: 1 Unable to

Hi All I have a Junghanns BRI 4 port installed where only the first channel of each line is working i.e. channels 1 and 4 work but 2 and 5 don't. Our config is the same on this box as 15 other similar installations where all works well. the only error I see is in /var/log/messages: Jun 28 15:49:31 pbxct kernel: qozap: CRC error for HDLC frame on card 1 (cardID 0) S/T port 2 Jun 28 15:51:27

Hi list! On a newly installed RHEL 4 box I'm trying to install bristuff-0.2.0-RC8n. Everything did compile but I am running into some problems with the zaphfc driver. First of all when I load zaphfc *before* zaptel (yes I know I shouldn't do that) I get a kernel panic and the box hangs. Not so nice, especially when you are trying to fix stuff from remote locations. But ok. Now for

We're using the Quad-BRI card from Junghanns.NET with corresponding drivers (bristuff 0.0.2). The driver tries to patch asterisk libpri, which fails for current version. Anyone got an idea what'S the latest version of asterisk / libtri usable with the Quad-BRI Card? Thanks, Martin

Hi list! I'm totally fed up with bristuff (or it's instability with a simple HFC-S card), 2 out of 3 times when people try to call they get the information tone that the number is not connected. I would like to try vzaphfc and I am looking for information on it. >From previous posts I found that the only place where the sources seem to be maintained and available is at the debian

Hi, For a significant time now (since about 0.2.0-rc8n) the qozap driver has become very verbose if an ISDN line is not connected... I get the messages below every couple of seconds in the asterisk logs. The "flaw" in the messages is the "Alarm cleared" message - The alarm cannot possibly be cleared because there is no physical media connected into that port!!! (BTW - All