similar to: Use Digium TE110P Single T1 / E1 PCI Interface Card for connect a old PABX ?

Hi i use now iaxmodem for receive fax and that's work very good with Hylafax ;=) Do you know if we can sent fax using iaxmodem and Hylafax ? when i test: d?c 13 13:47:21.12: [13725]: SESSION BEGIN 000000014 330426690268 d?c 13 13:47:21.12: [13725]: HylaFAX (tm) Version 4.3.0 d?c 13 13:47:21.12: [13725]: SEND FAX: JOB 2 DEST 0426690268 COMMID 000000014 DEVICE '/dev/iaxmodem1' FROM

Hi All, Can Asterisk dial extension which resides in the PABX? (eg. 2000) Sip Phone <-----> Asterisk <------> ATA (FXS) <------> (CO side) PABX <-----> Extension (eg. 1000) (2100 & 2101) can my sip phone call to pabx extension 1000? What will be my dial plan? I know I can connect to 1000 by

Hello all! I'm VERY new in using VoIP. I'm looking for any tip or trick to connect a physically PABX behind an Asterisk-System(or similar) via an SIP to Analog- or ISDN-Converter. The point is, I _need_ to deliver calls to extensions in the connected PABX directly (in ISDN-speech "DDI" (DirectDialIn)) without intervention of an operator. Is this technically possible, and if

Hi, We are trying to port over a PABX to our network. Both PRI's seem to be live however, whenever someone dials out from the PABX Asterisk happens to report : -- Extension '' in context 'samsungincoming' from '736327438' does not exist. Rejecting call on channel 0/31, span 2 If crc4 is turned off, it reports a yellow alarm. Any suggestions? Regards, Sahil

Hello team; While am aware and active user of astersk monitor function for recording, i would like to know if i can use asterisk as a pure recording server(like nice or witness) for some other PABX's extensions (both inbound, outbound and internal). Setup PSTN---Legacy PABX(with analogy n digital extensions)--- asterisk(record Legacy PABX extensions.) Sam -------------- next part

Hi all,as good? It would like to know if already they had had success, in the integration of the functions of asterisk, with one pabx legacy (Avaya)for that pabx avaya, could use the voicemail of asterisk. For sample, user of pabx avaya, it would have its calls directed for not attendance and busy, for asterisk and asterisk, it would send the same one for the voicemail. Best Regards Josu?

Hi all, I have an Asterisk server connected in a PABX (TELEDATA) by channel Unicall.. I`m having problem when somebody call from PABX to Asterisk.. Eg: When somebody dial 1234, I received 1111112222333333444444 in the Asterisk CLI... If somebody can help me... or already saw this... Everton Goularth Uberlandia - MG - Brazil _______________________________________________________

Hi guys! I'm having one or two issues with queues hosted by an Asterisk machine where the clients are on a legacy PABX - at least for the interim. I fully expect most of these issues to be non-resolvable, but thought I'd at least ask to find out if there is some way of working around the issues. The legacy PABX is an NEC 7400 ICS connected to Asterisk via an E1 ISDN link. Calls are

Hi anyone know where i can find all internatinal numbering plan in csv and for free or small price ? thanks Jpc

Trying again... *Summary:* I need to have 2 machines with 4 BRI connections, 2 in NT mode, 2 in TE mode and 1 machines with 2 BRI connections, 1 in NT mode, 1 in TE mode; What card(s) should I put in to these servers? *The long story:* I have 3 locations I want to connect using (*) servers. 1 of those has a single BRI with a Siemens DECT PABX. 1 of those has two BRI's with 2 Siemens DECT

Hello, I'm researching the possibility of using VOIP (SIP) with an existing PABX system. Ideally, the setup would be to dial an outside line through the PABX (that would actually link to the the VOIP gateway). At this point I would prefer not to purchase a hardware-based VOIP gateway. I would prefer to use a software-based gateway for research & testing purposes. Could anyone please

Hi all, I've been lurking here and reading the Wiki for a month or so now, getting information on the suitability of Asterisk for my installation. I'm responsible for the technical stuff at a mostly-inbound call centre in Melbourne, Australia. Due to our rapid expansion, it's getting close to the time to put our old beloved Fujitsu 9600 PABX out to pasture. I'm evaluating

Hi All, I have configure my Asterisk as follow (using Asterisk@home): [zaptel.conf] span=1,1,0,ccs,hdb3,yellow bchan=1-15,17-31 dchan=16 loadzone = uk defaultzone=uk [zapata.conf] [channels] switchtype=euroisdn pridialplan=local prilocaldialplan=local internationalprefix=00 nationalprefix=0 usecallingpres=yes busydetect=no ; not need on pri callprogress=no ; was yes but wiki says experimatley

Hi guyz I m very much new to Asterisk and i want to establish a PABX for my house at the moment i have X100 card(Configured) Asterisk PABX(Installed) Now i want to know how would i recieve call for e.g. i want during incoming call (after demo mess). if user press 9 (for e.g) the call redirect to host1(for e.g. again).or if ne user of gnophone want to dial outside how would he do so . N e sort

Hi all, I'm sure something similar has been discussed, but one can only wade through the archives for so long. I'm setting up a T1 and my telco has a bunch of questions it wants me to answer. I know much of the TE110p is configurable to do any of this, but I wanted to know if there is an optimal or preferred setup. Any help would be appreciated. Here is the quiz my telco is giving me:

Hi what is the best billing solution for Asterisk ? With WWW manager interface for user can see the real invoice... Thanks bye

Hi do you know if they have "external Box" (not internal card) for connect Analog Line and Pri/Isdn to asterisk for incomming and outgoing calls ... Thanks

Hi I have a small question on CDR Database: It's used by billing software no ? he have only one structure of data or they have multi structure with more information logged ? sample: cdr simple and cdr_extended thanks bye

Hi list, I have a terrible noise issue with Dell SC1430 + Digium TE110P. The digium card is not sharing interrupts with any other device, as I saw in Dell's BIOS and also with "lspci -vb" command. After changing coax wire, UTP, balum, digium card ... I have found that the problem is in Dell box, so now I'm running the same Asterisk config in other server with the same

This is a really rookie question: when should i use TE110P ISDN PRI Card? -- Necati DEM?R --------------------------------------- -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20100621/07d2917f/attachment.htm