similar to: Sangoma card dying after 1hour

Hello List Just want to check if anybody else is having this problem. Every time the PRI connections are disconnected, the card freezes, and I have to reload the driver, to make it work again. We are very seriously considering switching to Sangoma at this moment, due to this and other problems, but I want to know if there is a solution, and to make sure it isn't asterisk that's freezing

Hi all, My problem boils down to these errors: ... Unable to create channel of type 'ZAP' (cause 34 - Circuit/channel congestion) == Everyone is busy/congested at this time This is triggered by lines in extentions.conf such as: exten => _X.,1,Dial(ZAP/g1/${EXTEN},,W) The system is CentOS v5.2 with Asterisk 1.4.23 (druid-asterisk-1.4.23.1-2), a Sangoma A104

Hi, I have several 1.4.29 installations with Sangoma AFT101d cards. Normally we have been collecting the raw data and then graphing channel use for these customers with: asterisk -rx 'show channels' | cut -f1 -d' ' | grep Zap | sort -u | wc -l Then I recently noticed that there were some "zombie" calls in this list that were not actually active anymore. They go

I've been going back and forth with my telco for several days, trying different configurations to get a new PRI to come up. The bchannels are all up and the T1 is not in alarm status. The dchannel refuses to come up however. We've tried ni2, qsig, and now dms100 for the switchtype. The telco tech I've been working with says that he's been sending "reset all channels"

Hello, I have following problem with Sangoma A104 card: CLI> pri show span 1 Primary D-channel: 16 Status: Provisioned, Down, Active Switchtype: EuroISDN Type: CPE Window Length: 0/7 Sentrej: 0 SolicitFbit: 0 Retrans: 0 Busy: 0 Overlap Dial: 0 T200 Timer: 1000 T203 Timer: 10000 T305 Timer: 30000 T308 Timer: 4000 T313 Timer: 4000 N200 Counter: 3 NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI

I have a system that I am trying to get a port on a Sangoma A104d card connected to an Adtran 850 with 5 FXS modules and 1 FXO module. A problem I am having is figuring out what cable should be used from the port on the Sangoma to the JP2 port on the Adtran. Tried was a cross-over T1 (1->4, 2->5, 4->1, 5->2) as well as a straight T1 (1->1, 2->2, 4->4, 5->5). Neither one

Hi, I migrated from asterisk 1.6 to 11.3. The Server has a Sangoma A104 quadPri card installed. OS is a fresh installed Ubuntu 12.04 64bit libpri, dahdi etc. all latest releases.. Sangoma says... driver is compatible with ANY asterisk version... I tried driver 3.5.8... Setup ended with error. I tried (latest) driver 7.0.1 Setup went through, Asterisk is showing dahdi channels... all fine....

hi building a new setup, we want to try using sangoma cards. can these be used as time sources the same way as TE410Ps? thanks roy

That's just the thing, and it sucks, because the VoIP implementation actually works very good. Jon _____ Fra: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] P? vegne af list mail Sendt: 8. juni 2006 02:34 Til: Asterisk Users Mailing List - Non-Commercial Discussion Emne: Re: SV: [Asterisk-Users] I can hear only one way when I use

I have installed Asterisk on a CentOS4 box and then installed Asterisk from CVS. I installed a Sangoma A101 and connected it to a Adtran 600 using a T1 Crossover cable. The 600 has 12 x FXS, 12 x FXO interfaces. I ran through the wanpipe install instructions and configured it, now I can run [root@altpbx asterisk]# wanrouter hwprobe ------------------------------- | Wanpipe Hardware Probe Info

Greetings folks- I'm experiencing issues with a freshly installed box. When a call comes in via PRI (Sangoma AFT-A104), I see this in my logs: [Dec 15 14:26:10] WARNING[23546] chan_dahdi.c: Unable to enable echo cancellation on channel 12 (Invalid argument) [Dec 15 14:26:10] WARNING[23546] chan_dahdi.c: Unable to enable echo cancellation on channel 8 (Invalid argument) [Dec 15 14:26:10]

Hello, Digium does not provide snmp support to monitor their cards ! Anybody has tried Sangoma product A104 Quad T1/E1 or others ? Regards harry ___________________________________________________________________________ Yahoo! Mail r?invente le mail ! D?couvrez le nouveau Yahoo! Mail et son interface r?volutionnaire. http://fr.mail.yahoo.com

I upgraded from Tormenta2 to Sangoma A101. I followed the instructions, and installation was successful. zttool, ztcfg, all show card is installed properly. I copied the parameters from my old working zaptel.conf, zapata.conf and zapata-auto.conf. Verified on Sangoma website that these files are correct. Also configured wanpipe1.conf. But doing all this didn't start the PRI channels. It says

Hello Olivier Ive been testing the E61 phone for some days now, and we need to have an inhouse asterisk server, connected to our main asterisk server, to get it to work. That means, that you cant just walk down to your local airport, and use the IP part of the phone on their network. You have to have a non nat local server, to get it to run. Other than that, the phone can accept calls both

Hello Be aware that the Nokia E60, E61 and E70 does not support NAT. Just to be shure that you know that. A clever choice from Nokia, so that users has to have some local equipment from the telco. Jon -----Oprindelig meddelelse----- Fra: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] P? vegne af John Joseph Sendt: 7. juni 2006 13:59 Til: Asterisk Users

need help trying to figure out why calls hang when using multple ports on Sangoma card. we have 1 quad card with 3 T1 ports configured, Port1 acts as connection to teleco (to our T1 PRI) port 2 connects second system and routes calls to port1 port 3 is Asterisk pbx calls all go in and out properly but sometimes we get a call hang on when both sides hangup. this causes all calls to fail until

Hello, We are having issues with a NEW Sangoma A108D: -- Executing [691918892 at pbx1:1] Dial("SIP/xtravoip200-009d24b0", "DAHDI/g0/691918892|30|m") in new stack [Oct 1 10:04:43] WARNING[14171]: channel.c:3170 ast_request: No translator path exists for channel type DAHDI (native 76) to 256 [Oct 1 10:04:43] WARNING[14171]: app_dial.c:1237 dial_exec_full: Unable to create

Hello I can save you a lot of time, and tell you that it wont work. It does hold some registration information in the asterisk database, but most of the information is kept internally in Asterisk. Just FYI. Jon _____ Fra: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] P? vegne af Shenen Shenen Sendt: 9. juni 2006 11:37 Til:

How can I copy all the contenent of the asterisk database to another machine? I want copy all the active sessions from one asterisk@home to another one and running on the second(this I can do using vrrp protocol, it isn't a problem), I want copy only all the active sessions and softphone registrations to another asterisk@home and then run on it. -------------- next part -------------- An HTML

Hello List We are trying to redirect calls directly, instead of opening a new channel and dialing out. Etc: A calls B on our asterisk, and is directly redirected to C We have been told that this feature should be available on a PRI level, and is called Partial re-routing. Anybody has an idea of whether this is supported in Asterisk? Kind Regards Jon Sch?pzinsky Detele. No virus found in