similar to: Asterisk + Unicall + Telmex E1 MFC/R2 Argentina + Meridian

I've been trying to configure an E1 in Mexico using unicall, i went into vozdigital, googled this list, and finally followed this instructions: http://voip-info.org/tiki-index.php?page=Asterisk+MFC+R2 I have 10 PSTN numbers and 10 "lines" assigned, so i only have 10 "channels" assigned from my telco. However when i try to simulate a call using this call file: --------call

Hi all. When I place a call Im getting this error: Jul 25 09:50:07 WARNING[3200] channel.c: Exception flag set on 'UniCall/13-1', but no exception handler Lots of this messages appeared on my Asterisk full log and the CPU got 100%. Topology: Analog Phone - Hicom300H E1 - E1 Asterisk - IP Trunk Problem: 1. Calls from Analog Phone through Asterisk is ok, but the messages appeared.

I don?t know if the last message was with content. So, I sent again. I have installed a Digium card TE210P and unicall for use MFC/R2. I think that it?s all right but I can?t make and receive calls. I?m using asterisk 2.1 with the patch made by Jos? P. Leit?o and the follow libs: libsupertone-0.0.2 libunicall-0.0.3 libmfcr2-0.0.3 zaptel 2.1 My number is 34318300. The Telco send me only 8300.

Hello All, I'm facing problems with Unicall on this scenario : CentOS 4.3 - Running on x86_64 Asterisk 1.2.7.1 Zaptel 1.2.5 When running zttool , shows all Spans OK. But I can't receive and make calls. I tried to change many parameters and still doesn't work. Any clues ? * unicall.conf [channels] language=br context=incoming-pstn usecallerid=yes hidecallerid=no immediate=no

Dear Steve and *.* e1r2 developers and users, now MFCR2 is successfully installed! many thanks for your help. I'm living in Argelia. I have configure my MFCR2 according argentina R2 settigs. (look at the end of the message) the testcall run perfectly (only warnings and I think that is just debug). but I have many problems and when I run Asterisk-MFCR2, generally in the begging no errors

Hello there! I've problem with setting up unicall / mfcR2. can't find proper notation for channel, trying unicall/1, unicall/1/1001, unicall/g1, unicall/g1/1000 and still having no luck. klaudia*CLI> !cp call /var/spool/asterisk/outgoing -- Attempting call on Unicall/1001 for application Dial(363) (Retry 1) Mar 25 09:29:34 NOTICE[19920]: channel.c:2429 __ast_request_and_dial:

Hello I'm using mfcr2 support (unicall) in asterisk 1.4. Everything is working fine, asterisk can answer calls. But after some random period of time mfcr2 module stuck. When I make a call to my * box I can hear only signal of getting caller ID ("tritirirti" - like jumping on :) ) and connection is terminated by my telecom operator. When everything I ok after few seconds of this

Hi, I've finally got running Asterisk 1.2.14 with UniCall & MFC/R2 patches, I can generate calls and all seems OK but I cannot receive any call, this is what I get: MFC/R2 UniCall/3 <- 0001 [1/IDLE /Idle /Idle ] MFC/R2 UniCall/3 Detected MFC/R2 UniCall/3 Creating a new call with CRN 32769 MFC/R2 UniCall/3 1101 -> [2/DETECTED/Seize ack/Seize ack ]

Hi all, I still haven't seen my first post (cry for help) so I'm not sure if these are going through or not ... I've played with the box all day today ... I got it to quit seg faulting finally by playing with the config files. Currently I have 4 spans configured for a Digium TE420B (With Octastic DSP) Here is my zaptel.conf: (I know the device connected to spans 1-3 are providing

Hi. I am in the Brazil. I have a problem on Unicall for Asterisk 1.4. I am working with E1 with 30 channels. Message when it receives calls: chan_unicall.c:2603 handle_uc_event:unicall/1 protocol error.cause 32772. My files: /etc/zaptel.conf: span=1,1,0,cas,hdb3 cas=1-15:1101 cas=17-31:1101 loadzone = br defaultzone = br fxoks = 32-55 /etc/asterisk/unicall.conf: [Channels] language=br

Hello, i'm using asterisk 1.4.9 in fedora 7, i was compiled its with this package: libpri-1.4.2 asterisk-1.4.9 spandsp-0.0.4 unicall-0.0.5pre1 libmfcr2-0.0.3 libsupertone-0.0.2 libunicall-0.0.3 zaptel-1.4.4 i'm using a E1 pci card with R2 but they not work, when I start the asterisk its generate this log: [May 12 08:53:24] WARNING[30814] channel.c: No channel type

Hi, i have one Asterisk with a Digium E1 card, and a Meridian Nortel Release 11. I need to connect both of them. We are using MFC/R2 for this.. The Diagram: [ NORTEL ] ( AMI ) ------------------------------------------------ (DIGIUM) [ ASTERISK] we have green light at the digium card, and at asterisk we see all 31 channels as idle. But when i want to recive a call from the Nortel to the

Hi! Im having some troubles trying to configure * as a bridge between a telco and a pbx with R2, the scenario is this: ------------ E1/R2 --------- E1/R2 ------------ | Telco |-------------| * |-------------| PBX | | (Telmex) | --------- | | ------------ ------------ I can receive calls from the telco

Hello everybody, i'm from Mexico, at the time i?m working on a production server with asterisk 1.2.25 + spandsp-0.0.4 + libmfcr2-0.0.3+libsupertone-0.0.2+libunicall-0.0.3 and zaptel-1.2.22. I installed this version of astunicall that i downloaded from http://www.moythreads.com/astunicall/ Everything works fine, i'm able to make outgoing calls and recive incoming calls with all ANI and

I have a problem with inbound and outbound calls in asterisk. I read previous thread, and then test new versions of unicall, but I don't have success, the problem persist. The system suffers CPU peeks with a single conversation, with an interval of 5 or 10 seconds. My system has: asterisk 1.0.5 zaptel 1.0.4 libunicall 0.0.3-pre3 hardware: E100P Also, I made traces with strace, but all

It's bad enough that people insert long config/log files/dumps into messages to this list, though it's convenient. But when people include the entire redundant content in a quote in reply, it's really a waste. The digest messages are hard enough to navigate, even with an intro index, before making 95% of their content a redundant quoted dump. I know we've all got lots of bandwidth

Dears, After weeks trying to contact support of my telecom about 'Seize Ack' because that is not returned, was a lock for make calls on my E1s. Now I receive back de Ack and get ready to make calls, but the technical support reports to me that my attempts to call do not send any digits to the oder site (telecom station). 8 seconds after start 'Unicall event Dialing' the line

Hi, I am trying to set up an E1 line with CAS signaling using available unicall patches with libmfcr2 implementation. Inbound calls works well, I am able to get DNIS and ANI from incoming call, but I am still not able to make an outbound call with our local carrier. After tweaking of protocolvariant parameter in unicall.conf I was able to find proper values for inbound and outbound calls, but

I am having a strange problem with an asterisk servier using R2 Unicall in Mexico. Most calls go through fine but some of them give me an error like this: -- Executing Dial("SIP/86-db41", "Unicall/g2/014448343600") in new stack -- Called g2/014448343600 Feb 9 21:44:39 WARNING[23069]: chan_unicall.c:2644 handle_uc_event: Unicall/2 event Dialing Feb 9 21:44:45

I followed the how-to for R2 that coppice wrote on the webpage http://www.opencall.org/installing-mfcr2.html, now asterisk has channel unicall and when i test an incoming call I get the following errors. astbox:~/mediatel/libmfcr2-0.0.1# asterisk -r Asterisk 1.0.0, Copyright (C) 1999-2004 Digium. Written by Mark Spencer <markster@digium.com>