similar to: PRI Problems

<Correction in my zapata.conf file I used> Hey Everyone, So this is a problem I've been having for sometime now. I sent a few messages to the list with no luck. The problem is that when people dial into the Asterisk system using DID numbers, it works the first time or 2, then I get busy signals. A friend recommended I clear out the zapata and zaptel, start over, and recreate my

I just got a brand new A101 and am trying to install it in my test Asterisk box. The install went without a hitch. I followed the directions on the Sangoma Wiki: Wanpipe Asterisk Install http://sangoma.editme.com/wanpipe-linux-asterisk-install Wanpipe for Asterisk Configuration http://sangoma.editme.com/wanpipe-asterisk-configure It went perfect, no problems and Asterisk came up fine. I downed

Hello! I am trying to set up multi-link PPP using two T100P cards in one machine, and 1 T405P card (the 4-port one) in another machine. I have previously been able to get PPP working between the two T100P cards in separate machines.... The 4-port card seems to be my problem currently. I am trying to use the tor2 driver (from a fresh CVS download this morning). When I load the driver (or run

Hi, Maybe someone has seen this before... I've installed a new T100P, but it doesn't seem to work. I've attached the T100P to an Adtran 750 using a crossover cable. The Adtran shows a red alarm on the T1 interface. The Adtran has been set to factory defaults with FXS cards in 1-3 and an FXO card in 5. The T100P shows no signs of life--the leds are not lit. Should I be seeing

Hi, I have this error, I have a digium card TE110P Tiger3xx When I'm load the dirvers by this command modprobe wcte11xp I got this error "Notice: Configuration file is /etc/zaptel.conf line 0: Unable to open master device '/dev/zap/ctl' 1 error(s) detected FATAL: Error running install command for wct1xxp " when I'm Lunch the command ztcfg -vv I got this error.

I have installed Asterisk on a CentOS4 box and then installed Asterisk from CVS. I installed a Sangoma A101 and connected it to a Adtran 600 using a T1 Crossover cable. The 600 has 12 x FXS, 12 x FXO interfaces. I ran through the wanpipe install instructions and configured it, now I can run [root@altpbx asterisk]# wanrouter hwprobe ------------------------------- | Wanpipe Hardware Probe Info

I need some help getting a system running for one of my company's plants. I am running AsteriskNow 1.7 with Asterisk 1.6.2.10 and FreePBX 2.8.0.2. My D-Channel keeps bouncing. The telecom tech told me he thought that I might be using the wrong sync source, and I think I might have been, but I changed DAHDI system.conf to "span=1,1,0,ESF,B8ZS" (from

Hi, I am about to pull my hair out after trying to get our PRI up and working. We are switching from a Cisco gateway to an Asterisk box which provides the 23 phone lines for our office. So, because the Cisco gateway is working I can assume I have all the settings right (b8zs, esf, dms100, etc) and the PRI is live (because we are switching over). When dialing from PSTN, I get busy signal. When

I have been getting quite a bit of PRI Resets using my Quad PRI Digium card. Prior to the resets I am getting similar notices to the following chan_zap.c:7482 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 3 Telco claims the PRI's are fine on their end and that it is my unit. Is this timing? (google somewhat leads to this) I am running 1.08 asterisk zaptel

Good Day All, I am experiencing some weirdness using the E&M channel and hope you can offer a little assistance with the problem I am having. 1) call comes into channel 25 (Second Span first channel of a Digium Quad PRI from SBC-PRI) 2) Call is sent to channel 1 (First Span first channel on the Digium Quad PRI connecting an ADTRAN via E&M Feature Group D) 3) Between rings one and two

Folks, I recently swapped a TDM400 FXS card that was working perfectly into a new server (running recent CVS), and it's either misbehaving (unlikely), or I've missed something obvious (much more probable). Everything seems to be working, but I can't get any dialtone from it when I plug a phone into any of the 4 ports!! All of the jacks are lit (green lights) but they all seem dead

Hi all I'm trying to configure a TE410P in Europe with three E1s and a T1 channel bank (already bought in the US) to receive and make calls through *. I managed to get the E1s to work, but I'm having trouble with the channel bank (a Rhino). I have tried the bank in spans 1 and 4 changing jumpers in the card (always with no PRI connected, as I have no PRI where I'm testing now,

Out of the blue i started receiving the following error on my PRI line which connects my asterisk server to a Norstar 0x32 key system. The asterisk zaptel.conf file was configure as follows and this config worked for 6 months until friday. Nothing was changed on either system prior to friday. here is teh zaptel.conf span=1,0,0,esf,b8zs bchan=1-23 dchan=24 span=2,0,0,esf,b8zs bchan=25-47 dchan=48

I'm using two Rhino channel banks (first 12FXO/12FXS, second 24FXS). These connect to a Digium TE210P card. I'm running kernel 2.6.10 and I've tried Asterisk (w/zaptel) 1.0.9, 1.2 beta, and CVS from today. The results are the same for all versions: Right after I reboot, and modprobe wct4xxp, my analog phone connected to port 13 of the first channel bank (first FXS port) gets a dial

Hello All, I have a setup of ABE on rPath linux,Sangoma A101D, and a T-1 line (Not PRI) which is all happily coexisting and all lights are green. The T-1 comes in from the world into a "Shark Box" which splits the T into 384K data and 6 channels voice. The data side is working great. The voice side, not so great. It was originally broken out to 6 pots line and Verizon came back

We are currently working to trunk from a Nortel 81C to an Asterisk Server 1.4 running on Red Hat Linux. We have two PRI trunks which work with the exception of the clock slips, which is causing the Nortel to reset the PRIs once a hour. Thanks for any suggestions. 81C MSDL Asterisk Digium TE110P REQ prt TYPE adan dch 10

Hi all, i am stuck with the configuration of asterisk - modules are loaded ( zaptel and wct4xxp ) - i have zaptel.conf configure, output of ztcfg -vv --- snip -- rapid:~# ztcfg -vv Zaptel Configuration ====================== SPAN 1: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 2: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 3: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet

I have TE405P span connected to a patton/digi 2977 T1/PRI port. Zaptel starts up fine without any errors. Libpri is installed as well. But I get the following when trying to load asterisk ------- Jul 3 19:30:26 ERROR[8192]: Signalling requested is PRI Signalling but line is in Unknown signalling 896 signalling Jul 3 19:30:26 ERROR[8192]: Unable to register channel '25-48' Jul

Hi list, Ive got a server with 6 ports on it (4+2 port card) we have a DS3 delivering all voice DS1's to us. Carrier has a trunkgroup for the first 8 span (we only have the first 6 plugged in right now). Everything works fine until we fail the primary D channel (D's are on 24,48) the secondary then picks up and outbound calls do not work, if we reboot Asterisk the D on 48 comes up and it

(to mods: sorry for any extra work I've put you through. Posting from my work account, as proper) Hello all, I'm back. I've got that lucky feeling that this will all work out very soon, and I hope that that is true. The issue: In my * server I have a t100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm