Displaying 20 results from an estimated 10000 matches similar to: "Asterisk and TDM400P ?"
2008 Apr 14
4
Unable to load module chan_zap.so
I am having trouble with chan_zap.so not loading. When I load it from
modules.conf, Asterisk bails out without any error message. When I
load it from the console, it just says "Unable to load module
chan_zap.so" no matter what verbose level I am using.
dmesg says:
Zaptel Version: 1.4.4
Zaptel Echo Canceller: MG2
Freshmaker version: 73
Freshmaker passed register test
Module 0:
2008 Jun 06
1
Asterisk not picking up incoming calls from TDM400P
Hi,
I am having some issues with a new server install in Singapore.
Outbound calls work fine.
Inbound calls are not picked up by Asterisk.
Zaptel 1.2.25 and Asterisk 1.2.28 both built from source.
libpri installed
wctdm and zaptel load without error
Jun 6 23:34:03 fs01 kernel: [211138.372933] Zapata Telephony Interface
Registered on major 196
Jun 6 23:34:03 fs01 kernel: [211138.372937]
2004 May 19
4
TDM400P problems with 1 FXS, 1 FXO
Hi-
I'm totally stumped configuring my TDM400P with one FXS and one FXO
module. Before I got the FXO module, I used to have an X101P, and
everything was working very well. Now * doesn't seem to recognize the
FXO channel. I've searched the wiki and the list archives. Stock Debian
3.0 stable installation. Any advice? Thanks.
-- David
Here's my configuration:
modprobe zaptel
2005 Jan 06
1
TDM400P - Segmentation fault
Hi all,
I'm trying to install a TDM400P card, and I need some help.
Please, see below...
after dmesg command:
[root@voip root]# dmesg
via82cxxx: board #1 at 0xD800, IRQ 5
Zapata Telephony Interface Registered on major 196
PCI: Found IRQ 3 for device 00:09.0
PCI: Sharing IRQ 3 with 00:10.1
Freshmaker version: 71
Freshmaker passed register test
Module 0: Installed -- AUTO FXS/DPO
Module 1:
2006 May 09
2
Problems with TDM400P and FXO modules
Hi , I have an asterix (1.2.7.1) box with 3 TDM400P and 10 FXO modules, and
zaptel (1.2.5).
The problem is that 6 modules can't be initaized and i get the folowing
error:
May 7 09:17:37 WARNING[7739] chan_zap.c: Unable to specify channel 9: No
such device
May 7 09:17:37 ERROR[7739] chan_zap.c: Unable to open channel 9: No such
device
here = 0, tmp->channel = 9, channel = 9
ztcfg output
2007 Sep 11
1
TDM400P not answering or making calls
Hello,
I have recently purchased a TDM400P card with one FXO expansion card,
and I'm having problems.
The card does not pick up incoming calls. Asterisk detects the ringing
line and rings various SIP phones as required. When a sip phone
answers, the sip user hears nothing and the PSTN user continues to
hear ringing. Here is the asterisk output for an incoming call:
2004 Oct 01
1
Re: Problem with TDM400P
Greetings all,
I'm new to asterisk... Finally got two IP phones and two TDM400P's (one
with four FXO modules and one with four FXS modules)... Began experimenting
a couple days ago and have ran into a very aggrevating problem.
My system consists of the following hardware:
Abit BL7-RAID motherboard
Pentium 4 1.6GHz processor
512MB SDRAM
2 TDM400P cards
2 3Com 3c905
2004 Sep 25
3
Help with dialing out with TDM400P
Scenario,
I got some very good help earlier from Joseph getting me up and started
but I have a couple of small problems still.
Setup: FC2 Asterisk 1.0 Zaptel 1.0, TMP400P, FXS Port 1 FXO Port 4
Analog dialout line and Analog handset plugged in.
Problems:
1.
Incoming calls work and the phone rings and can be answered no problems,
(although I wouldn't mind being able to adjust the ring but
2006 Jun 20
3
TDM400P bad echo problem, tried lots of things
I have a bad echo problem on my TDM400P with one FXO module installed.
I have tried a few things, such as:
* setting rxgain and txgain to 0
* setting echocancelwhenbridged to no / yes
* settting echocancel to 64 / no / yes
* setting echocanceltraining to 800 / no / yes
* MG2 echo cancellation
* MARK2 echo cancellation
* KB1 echo cancellation
* AGGRESSIVE_SUPPRESSOR option of MARK2
Each time
2004 Jun 01
2
problems with TDM400P
Hi,
We have two of these 4 port FXO cards.
However, we are having some problems with incoming/outgoing calls.
The latest version of Asterisk/zaptel from CVS is being used. Voicemail,
internal SIP <-> SIP calls between Pingtel xpressa hard phones work
terrific, echotest is fine, and so on.
The zaptel and wcfxs modules load fine, and show all 8 FXO interfaces in
dmesg:
2005 Jul 03
1
TDM01B card configuration
Hello,
I am trying the setup the TDM01B card. 1 FXO. I
connected it to a regular home line. in the
/etc/zaptel.conf, I have
fxsls=4
In the /etc/asterisk/zapata.conf
I have:
signaling=fxs_ls
language=en
group=1
context=default
channel => 4
When I start asterisk, I get this error:
ERROR[10376]: chan_zap.c:6584 mkintf; Signaling
requested on channel 4 is FXO Loopstart but line is in
FXS
2006 Jun 10
1
ADSL modem, TDM400P, zaptel and not hanging up
I have an asterisk 1.2.9.1 machine with zaptel 1.2.6 running.
On the TDM400P, I have 1 FXS port and 3 FXO ports.
dmesg reveals:
Zapata Telephony Interface Registered on major 196
Zaptel Version: 1.2.6 Echo Canceller: KB1
PCI: Found IRQ 10 for device 01:01.0
PCI: Sharing IRQ 10 with 01:05.0
Freshmaker version: 73
Freshmaker passed register test
Module 0: Installed -- AUTO FXS/DPO
Module 1:
2006 Jan 11
1
Zaptel modules load, but Asterisk fails at startup
I'm running Asterisk on a Gentoo box with the Zaptel 1.2.1 drivers.
If I boot the machine without having the wcfxs module autoload, then
install the module with modprobe, asterisk works just fine.
If I boot the machine and autoload the wcfxs module, the module loads fine:
> Jan 11 11:06:55 asterisk Zapata Telephony Interface Registered on major 196
> Jan 11 11:06:55 asterisk ACPI: PCI
2003 Sep 15
1
TDM400p loading errors
Hi,
I have received a new card TDM400P revision E, from digium. When I tried to modprobe wcfxs it gave me the following errors:
Freshmaker version: 63
Freshmaker passed register test
ProSLIC on module 0 insane (1) 255 should be 2
Module 0: Not installed
ProSLIC on module 1 insane (1) 255 should be 2
Module 1: Not installed
ProSLIC on module 2 insane (1) 255 should be 2
Module 2: Not installed
2005 Jun 22
4
TDM400P DevKit Problem
I installed the TDM400P and installed it on a system running on Fedora
Core1, please refer to the steps below. I connected an analogue phone to the
FXS port.
When I pick up the speaker I don't hear the dialtone although when I press a
number key I hear a DTMF generated. What could be the problem?
I appreciate your help
1- First I installed the TDM400P in the PCI slot and connected
2004 Sep 25
1
TDM400P Newbie configuration hell :-)
Sorry to post such a newb set of questions but I have been hammering
about trying to get Asterisk running on FC2 machine reading everything
available (I think that is what stuffed me, shouldn't have read it all
:-) ).
Config
FC2 running Asterisk 1.0.0, with the h323 compiled in and installed
correctly.
Amazingly enough I have everything compiled correctly and installed.
I am running a
2007 Apr 30
1
TDM400P and Junghanns QuadBRI issue
Hi List,
I'm setting up a system with one TDM400P (2*FXO + 2 * FXS) and one Junghanns QuadBRI
on a Fedora Core 6 (Kernel 2.6.20-1.2944.fc6).
I'm using the bristuff-0.3.0-PRE-1y-e kit. It download zaptel-1.2.16, libpri-1.2.4
and asterisk-1.2.17
When it's the time for ztcfg to do its job it complains with
<ZT_SPANCONFIG failed on span 2: No such device or address (6)>
2004 Oct 05
1
Non-working module on TDM400P?
Hi all,
I was wondering if anyone had any pointers on how to determine whether or
not a module has gone wonky on the TDM400P?
I have a 2 FXO (channels 3 and 4) and 2 FXS unit (channels 1 and 2). The
bad (?) module in question is the FXO module on channel 3. I can't dial
in to or out of that channel; dialing in gives a busy signal, dialing
out just shows * hanging around after attempting a
2005 Feb 09
2
Problem using TDM400P FXS card
Hello, everyone
After having spent several time to look for any
solution for my problem, I decided to write here.
Here is the problem got a Digium X101 FXO card and
Digium TDM400P alias freshmaker (1 fxs module on it on
first port ) in my asterisk box. The X101 works
perfectly.
The problem comes from the TDM400, when i plug a
tested working phone on it , i get no dialtone; the
goal is to
2004 Sep 09
1
DevKit TDM400P module won't load
Hi all,
I have just purchased the DevKit from Digium and received a X100P and a
TDM400P (it has one FXS module).
The problem is that I can't get the kernel module (wcfxs) to load and
run. I have searched the archives and can't find anything about this.
Do the messages below ring any bells with anyone ?
There is no interrupt clash (see pci list below). I am running on a AMD
1.2G