similar to: Zaptel error

Hi I?m a new user and I do test with my hardware . I have a x100p and telephone vozip. And when I run this command asterisk ?vvvvc for to test it . My computer show it ?warning? [chan_iax.so] => (Inter Asterisk eXchange) == Manager registered action IAX1peers == Parsing '/etc/asterisk/iax1.conf': Not found (No such file or directory) Apr 2 07:45:12 ERROR[16384]:

When I reload the asterisk I get the following warnings: Oct 13 08:29:17 WARNING[10170]: chan_zap.c:10874 setup_zap: Ignoring switchtype Oct 13 08:29:17 WARNING[10170]: chan_zap.c:10874 setup_zap: Ignoring signalling Oct 13 08:29:17 WARNING[10170]: chan_zap.c:10874 setup_zap: Ignoring rxwink Everything works fine as far as I know, I can dial and complete calls. So why am I getting this

Anyone have any idea what this is talking about. Here is my zapata.conf [channels] switchtype=5ess signalling=pri_cpe echocancel=yes echocancelwhenbridged=yes echotraining=400 callerid=asreceived group=1 context=default musiconhold=default faxdetect=incoming channel => 1-23 Here is my zaptel.conf span=1,1,0,esf,b8zs bchan=1-23 # set this to 1-15,17-31 for E1 dchan=24 # set this to 16 for

Installing DevkitLite hardware (Very similar to John Lange's post on Tue Oct 08 2002) I cannot get anything to work on the phone connected to the s100u. I dont know what to do. Can someone please help me? I used the sample configuration files from digium documentaion that was supposed to be "sane" defaults for the kit. Very similar to John Lange's post on Tue Oct 08 2002 Here

Hello list! I?m having an issue when reloading Asterisk, I?ve had this problem in Asterisk 1.6.1.6 so I upgrade to 1.6.2.1 version, but I still have the same error. For example, I send a "reload" in Asterisk CLI and this is the output: isb152*CLI> reload == Parsing '/etc/asterisk/extconfig.conf': == Found == Parsing '/etc/asterisk/manager.conf': == Found

Greetings I was getting bad static crackle on a phone, so I reload from the latest CVS and did a make clean ; make install on zaptel, libpri and asterisk Now I get this error [chan_skinny.so] => (Skinny Client Control Protocol (Skinny)) May 28 13:59:42 WARNING[16384]: chan_skinny.c:2541 reload_config: Unable to get our IP address, Skinny disabled Urgent handler [chan_oss.so] => (OSS

Hi - I just got an A200 card with 1 FXO and 1 FXS module. Sadly, I can't make it work- currently, asterisk will not startup because of a bad module. Below are some log files/config files. If anyone has any suggestions, I'd appreciate it. I used Trixbox 2.0 and followed instructions on (http:// sangoma.editme.com/wanpipe-linux-asterisk-atHome) - no problems running through or

This is third time today that my Asterisk hangs up. It seams that I have problems with h323. I'm using ooh323 from Asterisk add-ons. I have the following configuration Asterisk 1.2.1 Asterisk-addons 1.2.1 Fedora Core 4 I'm using SIP phones and h323 trunk to my VoIP provider Like I said this is third time today that he hang's up. First time, I came at work and Asterisk was down.

Hello group I just update to the newest CVS now I'm not able to get asterisk to start. No error during the make or make install I did a make clean before the make;make install Any help would be great!!!! Here is the output asterisk -vvvvvgcd Parsing /etc/asterisk/asterisk.conf Parsing /etc/asterisk/extconfig.conf == Binding realtime_ext to mysql/realtime/extensions_table == Binding

Hi, I get the following message when I try to run Asterisk. This happened after I changed some of the configuration files: extensions.conf, zaptel.conf and zapata.conf. I have both TDM40B and X100P cards and am trying to use them together. Please let me know if there is something else I should do. Thnx, Gladys [chan_local.so] => (Local Proxy Channel) == Registered channel type

Looking at the error I tried moving chan_modem* out of the modules folder and asterisk started and its working again... Not sure what changed in the chan_modem_i4l.so but removing it from the folder fixed my problem. -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Eric Hall Sent: Sunday, January 23, 2005

Hello guys! I hope you bare with yet another newbie on the list! :-) I am trying to setup an asterisk installation in between a Siemens HiPath 3800 and my local carrier (Telefonica/Brazil). Both running R2. ISDN is not an option on the carrier. :-( I could apparently setup both E1s just fine according to zttool (both OK with no alarms) but, and this is where it starts to get

I'm not sure if I have a configuration problem or not. I am unable to dial out. When I try to dial in I can hear the phone ring on the dialling phone but Asterisk does not register anything. In zaptel.conf I have loadzone = au defaultzone=au fxsks=1 In zapata.conf language=au context=from-pstn When I do: zap show channels I get: Chan Extension Context Language

I have an Ubuntu system and went into Synaptic and checked asterisk for installation. Once installed, I started it with /usr/sbin/asterisk -vvvgc and got the following output with several errors and notices. Do I need to do more or are these ok? I expected to have some conf files in /etc/asterisk but there is nothing there. Thanks! Created by Mark Spencer <markster@digium.com>

Hi, I've been having a little problem with my asterisk servers, I have 4 identical asterisk servers setup (same hardware, same OS, same config). Once in a while (once or twice a day) one of the server crashes on the cron job reload. But I realized this only happens on 3 of the 4 servers. Tried to spot the difference between that one server that wasn't crashing. The difference I found was

Hi guys, I've been installing and configuring a TE110p card. The compile and install went very well. I'm using this on FC4 and I compile with linux26 as well checked I on the udev configs. zttool and ztcfg both indicate that the card is ready. But when I try to "load chan_zap.so" then I get the following Unable to load module chan_zap.so Jan 5 21:43:33 ERROR[6808]:

Hello all I just checked out the latest zaptel/zapata/libpri/asterisk/asterisk-addons from the cvs and ran through the entire make procedures. Everything seemed to go fine however now when I attempt to start asterisk, it says ok but it seems to be immediately crashing. The following messages are displayed in my /var/log/asterisk/messages file for the time right around the crash: Dec 29

Hi everyone, I am running asterisk on red hat linux 9 box. The sound card is Intel 82801db AC' 97 audio and the module is i810_audio. It runs well with other applications like xmms and the standard tests deliver a sound . I have also tried to record voice and that works well too. 1-)Now when i run asterisk and i dial out an extension to play any sound there is none. The same thing

I've put a t100p in our * server and I'm having trouble configuring it. It is directly connected to an Adtran TA 750 channel bank with two FXO cards (8 analog incoming lines total). I'm able to insmod and modprobe both zaptel and wct1xxp with no trouble, but when I start * with /usb/sbin/asterisk -c I get the following output: [root@rosella root]# /usr/sbin/asterisk -c Asterisk

I have a pretty basic Mandrake 10.2 w/KDE 3.2 and I installed Asterisk-1.0.1-2mdk. I installed the source of main and contrib from ftp, so at the install time I accepted all the packages needed to be installed too. The installation went smooth, but when I try to execute asterisk (#asterisk -vvv) I encounter few warnings I end with an error. At this point I didn't touch any conf file, I was