similar to: Parking on an extension

Hi I have a Polycom 501 phone. I set the park feature to 1 in sip.cfg and the button shows up just fine. However when you press it it does nothing. I have the t and T in the dial string. Is there some trick to getting it to work with asterisk 1.4. Thanks Kelly

Hi I have 2 asterisk servers running 1.2.12.1 and IAX2 with trunking and no jitterbuffer. Both servers are using sccp2 with 7940's and 7960's with 7914. Server 1 is my main VOIP server and is connected to the pstn and VOIP wholesale provider. Sever 2 is a branch site and all calls go to server 1. If I make 1 call on server 2 everything is fine. If I make a 2nd call so there a two calls

Hi I am trying to set up a hold system so that a call is always parked in the same spot no matter how many times it is picked up. My problem is I cannot fins a variable the identifies the call all the way through until it is destroyed. ${UNIQUEID} and ${CHANNEL} both seam to get lost when the call is parked. I tried setting set($[?${UNIQUEID}-hold?=?701?]) and

I have the standard parking.conf but extension 700 doesn't show up in my dialplan.... Why? I can dial 701 which tells me that I don't have any calls parked there. 700 just gives me invalid extension noise.... Should I have extension 700 defined elsewhere? Thanks parking.conf [general] parkext =a 700 ; What ext. to dial to park parkpos => 701-705

Hi I just got an AA50 from Digium and the paging command reboots asterisk when you use it. Digium says it is a requested feature and is of low priority. Is there any other way to page 10 Grandstream gxp2000 phones with meetme or some other command than the page command. Thanks in advance. Kelly -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi Is it possible to dial from within voicemail to reach another extension. I would like my customers to have a choice of dialing 1 to get my cell phone while in voicemail or to just leave a message at the tone. Thanks Kelly

Currently at our office, if I want someone else to pick up a call, I have to transfer the call to them. So I'm looking into call parking, which is ALMOST perfect. The missing piece of the puzzle: I'm extension 203. I want any call I park to get parked at extension 2203. I want a call my boss parks to park at 2205, since he's ext. 205. In other words, I want calls parked FROM

Is it possible to park a call through the manager interface? If yes; how? Regards Thorben -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050318/ec2a5f90/attachment.htm

Hello, Recently we have been using asterisk 1.6 and everything worked ok, all our productions server are 1.6. Recently we have upgraded one to 1.8 and multiple parking call are not working, which worked pretty ok on asterisk 1.6. Are there any major changes in asterisk 1.8 related to park call and multiple parking lots. Bellow is my config from asterisk 1.6 which worked, I`ve tried this in 1.8

Hi, I am facing the following issues with call parking: 1) Asterisk does not announce the parking extension:- I press # and hear "transfer" followed by a beep. I dial 700 but do not hear the parking extension number. 2) After parking time, the original extension rings and i accept the call. When I again try to park, the call park sequence fails. I have attached features.conf and

Is there any way to have Asterisk call an extension in dial plan instead of original extension after timeout? Like extension A puts the caller in parking lot, he leaves the phone and forgets about it, instead of having that phone rings after timeout, have a group of phones rings. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi: I want to make parking calls easier for my hard-working users. Is there a way to make the Polycom call park feature work with Asterisk? In case it just works out of the box, I haven't tried it yet; but the "call park" feature isn't enabled on the Polycom phones by default. -Stephen-

I have an issue with call parking and hope there is some undocumented feature for this. ;-) We are replacing our legacy PBX with asterisk, but to save money over time (handsets and network), I am trying to maintain the use of our legacy PBX. Asterisk extensions can not use the call parking features (not usable over trunk cards) of the old PBX, so I have to get the old PBX to use asterisk's.

Ok, a little patch that adds a little functionality to call parking. With that, you can pickup the older parked call, if many are in the parking lot. The default exten to do that is 750, but can be changed by setting "parkpick => exten" on parking.conf , like [general] parkext => 800 ; What ext. to dial to park parkpos => 801-820 ; What extensions to

How do you transfer or re-park a call that's been picked up from a parking lot? I don't see any options for specifying the transfer options on the parked call, so that you could transfer or repark it. -- Barry D. Hassler President, HCST http://www.hcst.net/ 937-427-9000 -------------- next part -------------- An HTML attachment was scrubbed... URL:

I'm trying to implement call parking with asterisk and Cisco SPA504G phones: features.conf parkext => 700 parkpos => 701-702 context => parkedcalls I defined one of the unused keys to park the calls: Key2: fnc=sd;ext=700 at 10.0.1.103;vid=1;nme=Park I also defined two other keys to pickup/unpark the calls: Key3: fnc=blf+sd+cp;sub=701 at 10.0.1.103 Key4: fnc=blf+sd+cp;sub=702 at

I am using Polycom 501s with asterisk 1.2.4. When transfering to call parking wih "#1" -> 700 the user is able to hear asterisk tell him what extension the call was parked on. However, when I press "transfer" -> blind -> 700 . The user is not able to hear what extension the call was parked on. It seems like the polycom is hanging up before asterisk is able to

Hello, all. I'm having a deeply frustrating time getting multiple parking lots to work and am wondering what I am doing wrong. I am using Asterisk 1.6.1.1. I defined two separate parking lots in features.conf as follows: [parkinglot_a100] ; SSI context => a100-parking parkpos => 900-920 findslot => next [parkinglot_a10] ; EBC context => a10-parking parkpos => 800-820

Anyone having trouble parking calls? I haven't tried it in a while, but it seems to have stopped working. If I dial 700, I get a invalid extension. I have "include => parkedcalls" in the correct context, and I can dial 701, which tells me no call is parked there. Any ideas? Parking.conf is stock.

Hi, Can anyone tell me if Asterisk sets some variable when doing a call parking (when someone presses an exten set in features.conf). In can't find this information on a wiki. Cheers ;) Andrew