similar to: Something is trashing /var/run

LD [M] /root/wanpipe/patches/kdrivers/wanec/wanec.o Building modules, stage 2. MODPOST *** Warning: "register_wanec_iface" [/root/wanpipe/patches/kdrivers/wanec/wanec.ko] undefined! *** Warning: "unregister_wanec_iface" [/root/wanpipe/patches/kdrivers/wanec/wanec.ko] undefined! CC /root/wanpipe/patches/kdrivers/wanec/wanec.mod.o LD [M]

Hi all, as good? I try to install asterisk-1.2.14, zaptel-1.2.12,libpri-1.2.4,addons-1.2.5 , sounds-1.2.1 and wanpipe-2.3.4-3 and hwec-utils-beta4-2.3.4 But it is not compiling drivers of the Sangoma, why udev's for board in "/dev/zap"(1-31, channel,ctl,pseudo,timer) is not created. But when I install a board TE110P Digium, udev's is created and asterisk functions perfectly. : )

Hello, there has been a post to this list somewhere arount april which said that it is possible to use a Sangoma BRI A500 card with zaptel and asterisk bristuff. That is, without sangoma_brid and sangoma_mgd daemons and without woomera channels. Could anybody give me a short hint how to configure this? I tried wanpipe-driver + zaptel + asterisk-bristuffed, but I couldn't get zaptel to

I just got a brand new A101 and am trying to install it in my test Asterisk box. The install went without a hitch. I followed the directions on the Sangoma Wiki: Wanpipe Asterisk Install http://sangoma.editme.com/wanpipe-linux-asterisk-install Wanpipe for Asterisk Configuration http://sangoma.editme.com/wanpipe-asterisk-configure It went perfect, no problems and Asterisk came up fine. I downed

Hi list. some info: zaptel 1.4.0 wanpipe 2.3.4-2 kernel 2.6.19.1 Debian I'm trying to build wanpipe on my server, but I got a error that it can't find config.h.. I found a post on an other unrelated mailing list which stated that includes/linux/config.h has been removed from 2.6.19. It also suggested replacing all references to config.h with autoconf.h make -C

Here's my planed setup : PRI from telco <--> (port 1 of A104d) * (port 2 of A104d) <--> PM3 The PM3, for those who don't know is lucent's portmaster RAS dial-up router. I had setup asterisk, zaptel, libpri, wanpipe (as I have sangoma's cards). In wancfg, I have port 1 as TDM_VOICE, with hardware echo on, span 1. Port 2 is TDM_VOICE, without hw echo, Clock as

Hi everybody! I'm triying to install a Sangoma A200-R FXO card on a Debian Linux 5 (Lenny), 2.6.26 kernel. To install wanpipe driver I type: WANPIPE_FOLDER# ./Setup install Everything seems to be ok. There are no broken dependencies and the hardware is well detected, even zaptel is recompiled with no errors, but at the time to compile wanpipe I'm getting this error message:

Hi list, I've just compiled and installed Asterisk 1.4.16 and when I try to run "zap show" I get the message "*No such command 'zap show'*". I have a Sangoma Remora A400D with 2 FXS / 10 FXO ports, I've installed the latest wanpipe too. zaptel-1.4.7.1 was compiled from the wanpipe installation, so I don't know what's happening here!!! Any ideas???

I have installed Asterisk on a CentOS4 box and then installed Asterisk from CVS. I installed a Sangoma A101 and connected it to a Adtran 600 using a T1 Crossover cable. The 600 has 12 x FXS, 12 x FXO interfaces. I ran through the wanpipe install instructions and configured it, now I can run [root@altpbx asterisk]# wanrouter hwprobe ------------------------------- | Wanpipe Hardware Probe Info

Hey! I am installing Sangoma A102D wanpipe driver and i got following error. what is this ? why dir isn't there ? wanpipe-3.5.16 # make dahdi DAHDI_DIR=/usr/src/dahdi wanpipe-3.5.16 # make install ....Send .... .... Installing Wanpipe Firmware update utility in /etc/wanpipe/util/wan_aftup install -D wan_aftup /usr/sbin/wan_aftup install -d /etc/wanpipe/util/wan_aftup/scripts install:

Hiya all, I have had no end of trouble trying to get my A101 E1 card working on a new asterisk installation. The sangoma tech people have ignored my emails about this. All the installation of wanpipe seems to go ok, and zaptel. it all installed compiled and does all the wanpipe hwprobe exactly as documented. Asterisk compiled ok, but when I run it give me Jun 27 11:12:18 ERROR[10528]:

I have a problem with a Sangoma card. It worked until yesterday. Now I keep getting this error: Jul 29 17:45:17 pbxacura kernel: wanpipe1: Enable E1 CAS signalling mode! Jul 29 17:45:17 pbxacura kernel: wanpipe1:w1g1: Rx Error: No 'DeviceSelect' from target: pci fatal error! (0x000FA000) Jul 29 17:45:48 pbxacura last message repeated 30946 times It is using Wanpipe 3.5.6 and Zaptel

Newest wanpipe (3.3.16) beta drivers do not compile against dahdi-linux 2.2.0-rc2 which is what you get when you get dahdi-linux-current.tar.gz Anyone have a workaround or patch? Error below ==================== Building modules, stage 2. MODPOST CC /usr/src/wanpipe-3.3.16/patches/kdrivers/wanec/wanec.mod.o LD [M] /usr/src/wanpipe-3.3.16/patches/kdrivers/wanec/wanec.ko make[1]:

Hello my friends, I want to make upgrades for all my software, currently i have the following versions: Asterisk 1.4.21.2 Zaptel Version: 1.4.11 WANPIPE Release: 3.4.7 libpri version: 1.4.5 I want to make upgrade for the last version of Asterisk 1.4, the last version of Zaptel (dahdi will be nice!), the newest libpri version and wanpipe What should i do? this is a production server and i

Hi, using Sangoma drivers: - doing 'lsmod', I see: zaptel ... wanpipe,wctdm24xxp,wctdm,wcfxo,wcte11xp,wct1xxp,wct4xxp,tor2 I'd like to avoid loading all these modules. What have I to do? - do I need to have 'zaptel' startup script under /etc/init.d ? Thanks -- Domenico Viggiani

Hi, We've exhausted our internal capabilities as well as Sangoma tech support and were hoping someone with some expertise could help us with a pointer. Briefly, our issue is as follows. Periodically (several times an hour), we get either of the following error messages in our asterisk messages log. These correspond with dropped outbound calls on a one-to-one basis when the second error

Hi all, I am having a very strange problem. I am terminating a PRI (5ESS switch type, national plan, 23B+1D (24)) into a Sangoma A104 and am not able to produce any audio heard on the PSTN end of the call. Not sure what's wrong - the card worked before under a Trixbox setup. I'm running kernel 2.6.19 (tried 2.6.24.3 but had to downgrade as wanpipe stuff would not compile), zaptel

Trying to install wanpipe 3.5.18. No errors during compile. But when I reach the point where wanpipe and dahdi_cfg is started, I encountered an error. Starting WAN Router... Loading WAN drivers: wanpipe done. Starting up device: wanpipe1 wanconfig: WAN device wanpipe1 driver load failed !! : ioctl(wanpipe1,ROUTER_SETUP) failed: : 22 - Invalid

Hi, I'm trying to install asterisk(v1.2.22) with FreepBX(v2.2.3) with a 4-Port FXO Sangoma card A200. I'm using Fedora 7 (x86_64) kernel version 2.6.22.1-27.fc7, but i'm having these errors: $ ztcfg -vvvv Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) Channel 03: FXS Kewlstart (Default) (Slaves: 03) Channel 04: FXS

Hi all, My problem boils down to these errors: ... Unable to create channel of type 'ZAP' (cause 34 - Circuit/channel congestion) == Everyone is busy/congested at this time This is triggered by lines in extentions.conf such as: exten => _X.,1,Dial(ZAP/g1/${EXTEN},,W) The system is CentOS v5.2 with Asterisk 1.4.23 (druid-asterisk-1.4.23.1-2), a Sangoma A104