similar to: lost packets when bridging zap and iax

asterisk-users Any help will be appreciated. This card did not connect with E1 line how to loop E400P card to test ? now I loop the card. span 1 ---span2 RJ45 pins 1--4 2--5 but show : When calling ,showing error: app_dial.c:764 dial_exec: Unable to create channel of type 'Zap' Asterisk Ready. *CLI> -- Registered SIP '2002' at 192.168.139.59 port 3289 expires 120

Hi Just received my spanky new TE405P today to replace my Cisco gateway... After much fiddling (I forgot to switch it to E1) I got it to work and everything "seems" to work perfectly on our ISDN PRI. If I dial-in from the PSTN to a SIP phone, the call goes through and if I hangup either the SIP phone or the remote end, the call gets disconnected and destroyed However, if I dial-in

Hello, I have a problem with Asterisk, on 10% of incoming calls the IP Phone ring but I don't hear the caller and the caller doesn't hear me (all IP Phones have the same problem). This problem appear also if the call is directly send to the second E1 of the digium card who is connected to an IVR. It does not depand on the charge of the server (I have the problem with only one call).

Hi all I have a server that has two TE412P (T1/E1+DSP) cards installed. One of them configured as an E1 PRI connected to PSTN and another one configured as a T1 E&M connected to Avaya PBX. Each card only uses two ports, so there are 2 E1 lines and 2 T1 lines connecting to this server. The purpose of this server is as a TDM trunk gateway that gets call from E1/T1 and then forward to an IP-PBX

Hello, There are 3 PRI's connected to the card each from different operators. Especially echo occured on span 3 is really annoying. Configuration files are as follows. Is there something wrong in conf ? Zapata.conf -------------------------- [channels] context=default switchtype=euroisdn usecallerid=yes hidecallerid=no callwaiting=yes usecallingpres=yes callwaitingcallerid=yes

Hi all, Does somebody know how I have to setup my TE405P ? Is it correct my configuration below ? Otherwise, can somebody help me ? Thanks, Angel. zaptel.conf span=1,1,0,ccs,hdb3 span=2,0,1,ccs,hdb3 span=3,0,1,ccs,hdb3 span=4,0,1,ccs,hdb3 bchan=1-15 dchan=16 bchan=17-31 bchan=1-15 dchan=16 bchan=17-31 bchan=1-15 dchan=16 bchan=17-31

Hi all, I still haven't seen my first post (cry for help) so I'm not sure if these are going through or not ... I've played with the box all day today ... I got it to quit seg faulting finally by playing with the config files. Currently I have 4 spans configured for a Digium TE420B (With Octastic DSP) Here is my zaptel.conf: (I know the device connected to spans 1-3 are providing

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello List, since some days i run into the problem that one span on a TE407P is not comming up correctly. With intense debug on that span i get: < [ 02 01 7f ] < Unnumbered frame: < SAPI: 00 C/R: 1 EA: 0 < TEI: 000 EA: 1 < M3: 3 P/F: 1 M2: 3 11: 3 [ SABME (set asynchronous balanced mode extended) ] < 0 bytes of data

Hi, Urgently response would be wonderful, system is a Fedora Core 2. I have a Ericsson BP250 connected to 1 port on the TE405P and another connected to a local telco ISDN30. I have been running CVS-HEAD from about a 2 months ago and upgraded it again just in cause it was a version issue (didn't fix it) but this is what I am getting. When a person calls out from an extension on the BP250 to

Hi All, This posting regarding PRI voice optimization, on dahdi 2.1.0.4. we have more than 4 machine running on 4 port PRI card with echo cancellation hardware based. i have enabled echo cancel from chan_dahdi.conf using echocancel=yes, now more than 70% of call get good voice but some of calls having issue for callquality and other voice related issues. now my question is that is there any

hello list, i have installed 2 diguim cards in my server using asterisk 1.4 (i use the old version with zapata.conf and zaptel.conf) i want to use the span 1 for group 1 and span 2-span 6 for the group 2 (i want to active the round-robin for span 2 and 6) in order to activate the WIMAX and FH please see the configuration below and tell me if there is anything wrong question 2: what is

Quoth Jon Morgan <jon.morgan at motors.co.uk> > >We have a 2 port Digium TE220P card, one span is configured to connect to our ISDN30 provider (British Telecom), the other span connects to our internal PBX. Here's the zaptel.conf snip: > >span=1,1,0,ccs,hdb3,crc4 >bchan=1-15 >dchan=16 >bchan=17-31 > >span=2,0,0,ccs,hdb3,crc4 >bchan=32-46 >dchan=47

Hi, I have two E100P boards connected to my PC. I wish to setup two E1-ISDN-PRI lines, the first SPAN with 15 channels and the second one with 30 channels. When I try to load zaptel modules, I get an error message: "Loading zaptel framework: Loading zaptel hardware modules: wct1xxp wcusb Running ztcfg: ZT_CHANCONFIG failed on channel 63: No such device" Follows my zaptel.conf:

We have a te410p, with the following connections: span 1 connected to a 32 Channel EuroISDN span 2 connected to a card in a legacy pbx (Meridian) span 3 connected to a 10 Channel EuroISDN span 4 connected to a card in a legacy pbx (Meridian) We have no need for the meridian now, and decided to turn it off. I did not change the zaptel.conf settings, nor the zapata.conf settings. When the

Does anyone have any experience ith configureing the sangoma A102 card for testing using a e1 cross cable i've configured and installed the cards properly even the lights on the card are green which proves that my cross cable is properly built too. my problem is with asterisk which gives me these errors PRI got event: HDLC Abort (6)on Primary D-channel of span 1 PRI got event: HDLC Bad FCS

hi, I'm trying to configure my newly acquired TE410P card to work as 4 E1 spans. This is supposed to be a drop-in replacement to the earlier E100P card. However, on loading the zaptel module it gets configured as T1 spans basically doing a 'cat' on /proc/zaptel/1 thru 4, it shows 24 channels per span. After this ztcfg fails saying 'ZT_CHANCONFIG failed for channel 97'.

Dear all I have now install TE210P 2 port E1 card on asterisk 1.4.10 on centOS 5 but thing is that i have connect 1 E1 port with avaya E1 back 2 back and second E1 card on Direct Telcom for outgoing for outside now i got this error when i call on avaya PRI asterisk think PRI_CPE and remote end also CPE i have configure /etc/zaptel.conf span=1,1,0,ccs,hdb3

hi, i'm having problems getting asterisk spliced between an E1 PRI (german Telco Arcor) and an Ericsson Business Phone 250 digital PBX. The Asterisk Server has a TE405P with it's port 1 connected to the E1 PRI provided by our telecommunications provider Arcor and port 2 connected to the E1 PRI of our Ericsson BP250. the setup before: Arcor TelCo PRI(E1)

Hello! I am trying to install a TN405P on a P4-3GHz-HT machine running Debian Sarge with kernel 2.4.27. When I start Asterisk in -vvvvc mode it always shows == D-Channel on span 1 up == Restart on requested on entire span 1 == D-Channel on span 3 up == D-Channel on span 2 up == Restart on requested on entire span 3 == Restart on requested on entire span 2 == D-Channel on span 4 up == Restart

I've been running Asterisk for months with no problems. I have grown to the point where I need an aditional TE cards. After many attempts I was able to add the second card without affecting the performance of the first. However, the second card is not working properly. Setup ===== - Running on a Dell Server. - RedHat 8 - Asterisk 1.0 - I have two TE410Ps on that box, card 0 assigned to