similar to: AW: Eicon Diva Server with v3.0 drivers

Hi, I'm trying to get an Eicon Diva Server4BRI card running under Ubuntu 6.06 - by downloading the v3 driver package from Melware and compiling everything. Yet, after activating the necessary modules (divas and divadidd) and interactively configuring the card (/usr/lib/divas/Config), starting up the adapter fails! The error "/usr/lib/divas/divactrl load -c 1 -Debug" produces

Hi; I've got an AAH installation where a customer wants to install an active Eicon DIVA BRI card. AAH is built on Centos 3.5 which is currently at kernel 2.4.21.37. Support for Eicon active cards is built-in. I've debugged and run the A@H install-Eicondiva script but when I try to run divactrl load -c 1 -f ETSI -Debug I get a response : A: can't get card type for DIVA adapter

Hi (Armin?) ! Today I had a problem with Diva Server 4BRI-8M 2.0. Asterisk 1.2.12.1 chan_capi-cm-0.6.5 divas4linux-melware-3.0.f-106.622-1 Asterisk could not receive and make calls on the BRI ports, although the ports looked fine within Asterisk. I usually use "/usr/lib/divas/divactrl dchannel -c 1" to test line activity. This time there was no activity (cryptic log

Hello, I have an issue getting the chan_capi module to load in asterisk cvs from today. Plain 2.4.20 kernel with melware patches for the Eicon Diva Server Bri card. I load the modules with: modprobe -v divas divacapi I load the firmware with: divactrl load -c 1 -f ETSI -vd6 Output in /var/log/messages is: Nov 9 19:26:26 voice kernel: Eicon DIVA - DIDD table (http://www.melware.net) Nov 9

Hi (Armin)! Does someone knows how to identify the type of the card? The delivery note says it is a V-4BRI-8M, whereas lspci reports a 4BRI-8M. What is it really? Are there any Eicon tools to identify the card type? thanks klaus 0000:0a:03.0 Network controller: Eicon Networks Corporation Diva Server 4BRI-8M Rev 2 (rev 01) Subsystem: Eicon Networks Corporation Diva Server 4BRI-8M Rev

Hi Everybody, Has anybody tried the above (or indeed any other 4XBRI cards) successfully with Asterisk. As far as I can see the above mentioned card is an active ISDN card but supported by it's own I4L driver. This leads to interesting questions particularly regarding echo cancellations (which usually doesn't work on the cheap passive cards with one exception as far as I can see).

Hello, I just received a couple SX440isdn phones and was wondering if they can be plugged into a Diva 4BRI port in NT mode and work with asterisk+chan_capi? I know they probably work fine with mutliHFC cards with either bristuff of chan_misdn but since I have some spare Divas, I was curious about their potential as phone ports. The Diva's 3 and 4 ports are already set to NT mode at boot

Are there any step by step instrunctions on how to install drivers and I guess bristuff for this card? Just need to use it to handle voice on 2 BRI circuits (UK) then utilise with Asterisk and some Digium cards handling POTS phones (and some VoIP out the back). It's the EICON card stuff and how to make it all work I'm finding confusing? Steve -- NetTek Ltd UK mob +44-(0)7775 755503

Hello! I finally found a working solution. calling divactrl with the parameter -n [0..20] gives the DID-length means, if you wanna have 123-XXX in digit-wise mode, then call divactrl load -c 1 -n 3 -f ETSI and the card will wait for n digits. regards, Sebastian -----Urspr?ngliche Nachricht----- Von: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com]

Hello all, I'm having problems getting chan_capi 0.3.5 to work well with an Eicon Diva Server card using using the driver from linux kernel both 2.6.10 and 2.6.12 (vanilla versions). I have a (really two) producci?n system(s) running chan_capi in another identical Eicon Card using kernel 2.4.27 and the Diva Server drivers from Eicon. I installed an compiled the source level rpm

Hello everyone, I'm having some errors while compiling the source code for an Eicon Diva BRI card. I am using Fedora Core 6 with a compiled from source Linux kernel 2.6.19. I have downloaded the Eicon Diva source RPM (divas4linux_EICON-106.12-1.i386.rpm) and installed it already. When I go to /usr/lib/eicon/divas/src/ and run ./Build, everything starts correctly until that part where it has

Hi Armin! I want to backup my Eicon Diva configuration (I'm using melware v3 drivers), but I could not find them. Where does Config Wizard stores the configuration? thanks klaus

Hi! This weekend we had a problem with our Asterisk Box which ran flawlessly for nearly 4 weeks. The Asterisk server sits between the PSTN and a Siemens PBX and bridges 2 BRI lines. No calls, not incoming, not outgoing. The admin rebooted the Dell Box and then everything worked fine again. Now, I'm analyzing log files to find the cause. During the Asterisk outage the logfiles only show

Hi I have installed 2 x Eicon BRI ISDN cards into a Suse 9.2 server. We can use all 4 lines for out going calls fine, but on incoming we can only use 2. On calling in using the main msn, the 3rd line gives a an engaged signal. I have unplugged 1 of the cards, and the other card takes the 2 calls. I then swapped this around, and this also works fine. But when using both cards, we can only use

Hi! I have some (short) question about the Eicon DIVA (V-)4BRI cards I want to have (short) answered before buying the DIVA card. I know there are several Eicon guys active on the list, thus I ask on the list instead of directly to Eicon so that all other will benefit as well. 1. Do Eicon DIVA (V-)4BRI cards support TE and NT mode? 2. Can the clock (master/slave) be configured independent

I am trying to understand the difference between the divas4linux available from the Eicom/Dialogic website and the melware version. Am I right in thinking that the melware version is for Trixbox or Asterisk but the Dialogic version is for Asterisk only (i.e. will not work with Trixbox?). I've noticed that some of the things mentioned on the Dialogic web site as included with Divas e.g.

I just wanted to let you know that it's possible to use Eicon DIVA PCI 2.01 ISDN cards (not "server" divas) with asterisk. First thing to do is to load the module. If you have two of these cards, you should do it like that: modprobe -v hisax protocol=2,2 type=11,11 And now you can have up to 4 incoming calls with two cards (try calling yourself and see if anything gets into

Hello, I want to use a 4 port ISDN card from EICON/DIALOGIC in our asterisk server. The system is a Ubuntu 7.10 with kernel 2.6.23.1. The compilation of the kernel finishes without any problems. I have downloaded and installed the deb-source package that EICON/DIALOGIC offers. Th installation script crashes with the following error messages: # LOG ---- START SECTION read kernel version

the interesting fact is, it works. I dunno why. but it works :o -----Urspr?ngliche Nachricht----- Von: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] Im Auftrag von bladerunner Gesendet: Freitag, 6. Mai 2005 15:56 An: Asterisk Users Mailing List - Non-Commercial Discussion Betreff: Re: [Asterisk-Users] CAPI on ptp with variable length digits

Hi list, Does chan_capi work with kernel 2.6? The Eicon Diva server card loads fine judging from /var/log/messages but Asterisk gives an error when trying to load the chan_capi module. I'm using chan_capi-0.3.5, zaptel-1.0.0, libpri-1.0.0 and asterisk-1.0.0 on a Fedora box with kernel 2.6.8-1.584. Zaptel and ilbpri work fine as does *. I have seen a msg that may be related and don't know