similar to: GXP-2000 MultiPurpose Keys

I'm communicating a softphone (SJPhone) to a Grandstream phone GXP-2000. The codec order on each one is the next: SJPhone: GSM - iLBC - PCMA - PCMU GXP2000: G729 - GSM - PCMA - PCMU (I have a G729 license, so there's no problem with transcoding G729) In my sip.conf, I've defined the following codec order: disallow=all allow=g729 allow=gsm allow=g726 allow=alaw allow=ulaw And my

Hello list, this is the communication between an Aastra 5000 PBX and Asterisk, where the Aastra makes a call to Asterisk. For some reason, Asterisk responds with 401-Unauthorized and I don't know why. Calls go well with Panasonic PBX, Avaya PBX, Alcatel-Lucent PBX but NOT with this Aastra. A1.A1.A1.A1 = IP-address Asterisk PBX AS.AS.AS.AS = IP-address Aastra PBX Aastra PBX makes a call

Hello, I have some problems to use G722, when my client sent an invite request to asterisk using G722/16000 codec asterisk respond with G722/8000 codec. I dont know exactly if Asterisk supports G722/16000 codec?? If yes how can I activate It?? Thanks. Rachid. Below wireshak trace:

Hello, a person trying to call me by my phone number is getting the error 488 Not acceptable here. I googled that error, seems like this error is normally caused by a failed codec negotation, though I have no clue how I could have read this out of the logs. Anyway, my setup is as follows: Asterisk 1.8.13.0 - NAT - Sipgate SIP Provider The user calling me is also using Sipgate and is calling my

I thought - what about the software - maybe it needs updated. After doing so I get a list: Audio codecs PCMU (8000 Hz) PCMA (8000 Hz) opus (48000 Hz) L16/16000 (16000 Hz) G.726-32 (8000 Hz) L16/8000 (8000 Hz) speex/16000 (16000 Hz) speex/8000 (8000 Hz) -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello: I have this situation: I can make calls internally, I can make inbound calls but I can't make outbound calls. Thanks in advance. These are my devices: * asterisk 11.8.1 = 192.168.1.22 * sipphone grandstream gxp2160 = 192.168.1.5 * gateway audiocodes mp-114 2fxs-2fxo = 192.168.1.4 port 1 (FXS) connected to an analog phone port 3 (FXO) connected to the PSTN These are my

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, I'm setting up an Asterisk system which is connected to an Alcatel 4400 PBX. On the * I permit g729 and gsm as codecs. If I try to transfer a call by hitting the # key, I get this messages and nothing happens on the phone: WARNING[30110]: codec_ilbc.c:175 ilbctolin_framein: Huh? An ilbc frame that isn't a multiple of 50 bytes long from

OK, it stopped working. It turns out the transport and endpoints in PJSIP are ok. I can send an invite from my unregistered snom phone and I can see some activity in the CLI. However, when I dial from my snom to Kamailio and have it pass the message to asterisk, PJSIP seems to ignore the sip messages even though they are there. Is there something wrong in the invite that I'm missing? U

I have the following scenario: PSTN gateway (202.180.nnn.nnn) -> OpenSER 1.0.1 (147.202.nnn.nnn) -> Asterisk 1.2.16 (203.89.nnn.nnn) When an incoming call is received, often (but not always) Asterisk repeatedly sends a SIP 200 OK message and eventually hangs up the call. sip.conf [general] port = 5060 ; Port to bind to (SIP is 5060) bindaddr = 0.0.0.0 ; Address to bind to (all

Hello, I am trying to setup a Grandstream GXP2160 IP-phone with secure calling (SRTP). Secure signaling SSIP for registration is working great ! I follow this guide : https://wiki.asterisk.org/wiki/display/AST/Secure+Calling+Tutorial But when I try to make a call with SRTP, I get stuck. There is an initial INVITE which is anwered with a 401. There should follow a new INVITE with a nonce,

im having a strange problem related to call-limit for peers. well im not sure if its related to call-limmit or not. Bottom line is: I call a user A, from user B. user B hears silence, untill it goes to voicemail. when user B hangsup. user B's call limit is reset to 0 but user A's call limit is not reset.strange thing is user A's status on cli is shown as NOANSWER, while user B did not

I have spent the morning on this project, still without success. Summary: Yesterday I inadvertently unplugged my Grandstream phone. I might add I did a rebuild of my s/w from CVS at the same time. Since then, the Budgetone seems to talk SIP just fine, but the RTP being sent to it by asterisk "doesn't make any sound." It was suggested I do a factory reset of the phone, which I

We have a system where calls are coming in from telcos via an opensips server and then being redirected out to a regular sip destination. There is no NAT, DTMF features, call recording, or codec translation being performed so I would expect asterisk to issue a reinvite after the call is answered and switch the audio however it is not happening. Here is the sip peer information for the call

I see this device : Axis C8033 Audio Bridge Quick Specs: Communications Protocol: SIP. Ethernet Ports: 1x 10/100. PoE: 802.3af/at Type 1 Class 2. Additional Interfaces: Audio: one-way/two-way, mono. Audio Codecs: G.711, G.726, WAV, MP3. Edge Storage: microSD, microSDHC, microSDXC. Operating Temperature: 4°F - 122°F. What is Codec WAV and MP3 to asterisk ??? Jerry -------------- next part

Hi! I'm trying to set up a SIP trunk so that I can test calls, etc., between a new Asterisk box, and an old 1.4 box. --------------------------------------------------------------------------- New box: root at asterisk1:/etc/asterisk# head -1 sip.conf #include siptrunk.conf siptrunk.conf: [box1] ; All box1 extensions; see extensions.conf type=peer context=adhearsion host=172.17.0.17 ; IP

Thank you Melissa. I love the phone but the dial keypad is a little bouncy. I was hoping for a more solid feel like on the analog PT390's or my quality standard, the Nortel 9417CW. Other than the MWI problem, I'd like more documentation on the configuration paramters. I have found little online configuration documentation other than very basic stuff on the Sayson website. I'd

Hi All, I posted this a couple weeks ago with no response, I'm hoping that someone will see it this time around and be so kind as to offer advice for resolving this issue (or point me in the direction of a better place to ask) "Some" (but not all) calls on one of our Asterisk boxes are being dropped in Voicemail -- only in voicemail -- after about 20 seconds with the error logged

Hello all, I HAD video working before I upgraded to 1.08 (latest stable with Gentoo) and now it won't work. I just see noise bars and not the video. I know the camera works as I can use it in other programs such as AIM & Yahoo. I have the following setup: sip.conf [general] videosupport = yes port = 5060 ; Port to bind to (SIP is 5060) bindaddr = 0.0.0.0 ; Address to bind

I am having a problem with one of my callers who is using either g729 or alaw.  I can do alaw but not g729 so asterisk should negotiate alaw right?  In fact from the sip debug it looks like it does, but then I get the dreaded "channel.c:5630 set_format: Unable to find a codec translation path: (g729) -> (alaw)" and the call hangs up.  Why? Last minute thought: Is it possible that

Folks! I would appreciate if someone could send me a simple working h323 configuration file oh323.conf that is part of asterisk@home installation. I have tried to use the oh323.conf content listed on WIKI but it is just not working as my H323 endpoint ( PA168 based ATCOM Phone) cannot register. I need a working example of this file for similar phone. Seshu