similar to: PRI and BRI

Hi, I plan to setup an * Server with a TE10P PRI card as E1 and a BN4S0 4 Port BRI card in one box. I tried it first with the bristuff drivers from Junghanns. The BRI card worked fine alone, but as soon as I load the zaptel driver for the TE110P the BRI card says, that the port is down. So I tried it with mISDN. But it seems that this stuff is still unstable (Asterisk refuses to start at first

Previously incorrectly sent to asterisk-dev list, sorry. I tried today while connected to a Jtec QSIG E1 card, with DAHDISendCallreroutingFacility with the following test dialplan: Extension 4888 is on the Fujitsu [incoming] exten => 8688,1,Answer() exten => 8688,n,Playback(connecting) exten => 8688,n,DAHDISendCallreroutingFacility(4888,8688) exten => 8688,n,Playback(goodbye)

Hi I'm having difficulties getting up my TE110P (running as a E1) when I connect it to the PRI. If I start the server with a loopback connector everything seems fine and the led is green but when I connect it to the PRI the flashing starts .... I can't seem to find anything in the log that suggests what could be wrong .....Aug 8 11:33:00 DEBUG[1369]: Updated conferencing on 31,

Hi All, Can anyone recommend any test kit that you can hook up your Pri/Bri cards to without having actual ISDN in your office. For example testing an * system before it goes to a clients office. Thanks, Gavin.

Hi, I configured an asterisk box with 1 Digium Wildcard TE110P T1/E1 Card 0 I setup the jumper in e1 position. my zaptel.conf : defaultzone=it loadzone=it #gestione PRI span=1,0,0,ccs,hdb3,crc4,yellow bchan=1-15 # set this to 1-15,17-31 for E1 dchan=16 # set this to 16 for E1 bchan=17-31 # set this to 1-15,17-31 for E1 # Asterisk starts correctly, I see th 30 channels. Anyway I cannot put

Hi, I wonder if anyone is using Digium's TE110P card on an E1 connection. I have been try to, but so far it wasn't much of a success. It only works more or less in EuroISDN as PRI CPE. And even that config gives me some trouble with channel negotiation. My current config: *zaptel.conf:* span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=be defaultzone=be *zapata.conf:* [trunkgroups]

Hi all, I've setup a PBX in production environment last week but we have immediatly find out drop conversations and lot of errors (in asterisk logs) like: Apr 10 17:30:48 NOTICE[25154] chan_zap.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 2 My configuration is: Motherboard: SuperMicro P8SCT (Intel E7221 chipset) Hypertrading and APIC enabled CPU: P4 3GHz Digium TE205P

Hi, I've connected a TE110P from digium with a 2 E1 to a Siemens PBX using asterisk from ubuntu linux. Everything is working as expected. This box is being used as a H323 gateway to the pstn. There are few complains but it is working pretty well overall. There is one thing that is bothering me. Asterisk says: May 22 05:03:39 WARNING[9360]: PRI: !! No channel map, no channel, and no ds1?

Having seen all the discussions about troubles with faxing I am thinking of another solution, keeping it all digital. I want to put two ISDN BRI cards in a faxserver (not running Linux). The two BRI ports will be connected to a QUAD BRI card in an Asterisk box. The asterisk box will have a single PRI span for communication to the PSTN. Basically the setup will be: Faxserver BRI ->

Hi, I am thinking of starting a project at Work to pilot to use of Astrisk and VOIP, and would like to tie in several projects together. Currently we are looking at purchasing an ISDN and H.323 based video conferencing system from Polycom. It suggests the use of 3-4 BRI lines (ie 6-8 B channels, but in the form of individual BRIs). We need ISDN for the video conferencing to communicate with

Hi!, this issue makes me crazy. I read a lot of docs, also * mailling list and I try a lot of things without success. Any help will be appreciated. Here is the info: Hardware: -------------------------------------------- Supermicro Server with motherboard X7DB8, chipset Intel 5000P, Xeon 5050 Digium TE110P Software --------------------------------------------- Asterisk version 1.2.12.1

Deat all, I am in middle of integrate Asterisk with Toshiba astrata legacy pbx. Following is my setup *Asterisk <-> Digium TE110P <-> E1 card in toshiba pbx <-> Toshiba PBX* A =============================================> B C <============================================ D Asterisk PBX and strata PBX connected using back to back E1 cross cable. Physicall connectivity

hello list, i have a problem regarding the synchronisity (clock source) when using multiple cards. e.g. when having connected one PRI port of our TE410P to the telco, i need to have the analog card like the TDM400P or a B410P synchronous to the clock of our telco provider. otherwise faxing on the analog cards does not work or i get cracking noise or even hangups on my BRI lines, due to bit slips.

Paul, Ah, I see. Our echo is largly under control now. It took me a while to figure out the gains and get them tuned, and now the echo only leaves very small artifacts. Nonetheless, this still provokes the odd complaint here and there. We use VOIP for outgoing calls when our POTS lines are congested, and we find zero echo during those calls. Therefore, I assume that our handsets (Cisco

I am running Asterisk 1.0.9 and have been running all my calls through a VSP over a IAX2 trunk however we have recently purchased and connected a TE110p to a PRI ( E1 with 16 voice channels ) through Optus. I can make outgoing calls via it fine, however incoming calls are dropped after a few seconds ( or as soon as a command like Playback, or the call is picked up if forwarded to a SIP

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all I have already a fully operational Asterisk PBX connected only to the IP world. As a necessary step before smashing our current PBX, I need to install and configure an ISDN card able to take an incoming E1 line provided by Eircom. That's the one and only ISDN line we will ever have, so I am planning to get a single port card similar to

Howdy: Does echo only occur on analogue PSTN lines, or can it also occur on PRI and BRI lines? If so, for the same reasons? This is a part of our consideration to transition to BRI. Sincerely, Brent A. Torrenga brent.torrenga@torrenga.com Torrenga Engineering, Inc. 907 Ridge Road Munster, Indiana 46321-1771 219.836.8918x325 Voice 219.836.1138 Facsimile www.torrenga.com

Helo, I have problem with Digium TE110P connected to CISCO 3640 (port on NM-HDV-2E1-60) wth PRI E1 link. I use CISCO now for testing but when I tried with real PBX problem was exactly same. I have this messages in Asterisk conole and log sometimes: NOTICE[1115] chan_zap.c: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Usually 2-5 such messages in series, can be repeated after 10

Hi All, The link http://www.voip-info.org/wiki-Asterisk+Data+Configuration talks about how a Digium PRI card can be setup for data, and also be used by asterisk to handle voice. Is the same or similar possible with BRI ? There are a few links on the Wiki to BRI cards, and that BRI can be supported through CAPI compatible hardware. That will take care of voice. What I want to do is use a BRI

Perhaps everything isn't as spiffy as I thought When running zttool the card still reports as internally clocked Zaptel.conf: # Global data span=1,1,0,ccs,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 loadzone=se defaultzone=se And as pointed out by Peter I do get a lot of D-channel warnings ... Aug 9 16:21:25 NOTICE[1350]: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 And