similar to: Connect 2 Asterisk Servers via PRI

Hi, I am getting this message on the * console on my first pri span. Pri show span show it is down, and I can't make any calls from the span. Apr 27 07:40:23 NOTICE[23988]: chan_zap.c:8202 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Apr 27 07:40:23 NOTICE[23988]: chan_zap.c:8202 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Apr 27

I receive this error on the asterisk console and it is pretty much ALWAYS coming up. Sometimes there will be a break where it does not display. We had our PRI provider test the lines and they claim that there is no signalling problem. It doesn't matter if there are no calls or if there are 10 calls in progress the error is still displayed. I also get an annoying popping or clicking sound

I have been getting quite a bit of PRI Resets using my Quad PRI Digium card. Prior to the resets I am getting similar notices to the following chan_zap.c:7482 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 3 Telco claims the PRI's are fine on their end and that it is my unit. Is this timing? (google somewhat leads to this) I am running 1.08 asterisk zaptel

Hi fellow asterisk users, I am running Asterisk 1.4.29 with an Digium TE121 card (wcte12xp kernel module) an approx. 100 snom320. The whole installation is running without issues since 5 months. Without having changed anything on the asterisk server for at least 2 months, i noticed "clicking sounds" at external calls over the PRI. Asterisk constantly throws the following messages: ...

Hello, I have following problem with Sangoma A104 card: CLI> pri show span 1 Primary D-channel: 16 Status: Provisioned, Down, Active Switchtype: EuroISDN Type: CPE Window Length: 0/7 Sentrej: 0 SolicitFbit: 0 Retrans: 0 Busy: 0 Overlap Dial: 0 T200 Timer: 1000 T203 Timer: 10000 T305 Timer: 30000 T308 Timer: 4000 T313 Timer: 4000 N200 Counter: 3 NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI

Hi all, Last night I went to replace an Asterisk 1.4 + mISDN + b410p box with Asterisk 1.6.2 and DAHDI BRI - to no avail. I had two servers so copied network setting etc from the working one, moved the card across, ran dahdi_genconf etc and it didn't work. Here's the console output with notices disabled: lucas*CLI> pri intense debug span 1 Enabled debugging on span 1 [Dec 16

Hi all, as good? I am trying to go up a board TE110P with link E1 ISDN PRI to establish connection with a central office Siemens HiPath 4000. But I am having the following errors: Server1:~ # asterisk -r Asterisk 1.2.10, Copyright (C) 1999 - 2006 Digium, Inc. and others. Created by Mark Spencer <markster@digium.com> Asterisk comes with ABSOLUTELY NO WARRANTY; type 'show warranty'

hello all, i'm using TE110P and all configuration prosess is done. but after i do the 'modprobe' for zaptel and wcte11xp, follow by ztcfg -vv and asterisk -vvvgc i have this error. *CLI> May 27 14:44:33 WARNING[3059]: chan_zap.c:8534 pri_dchannel: PRI Error: We think we're the network, but they think they're the network, too. May 27 14:44:34 WARNING[3059]: chan_zap.c:8534

Hi!, this issue makes me crazy. I read a lot of docs, also * mailling list and I try a lot of things without success. Any help will be appreciated. Here is the info: Hardware: -------------------------------------------- Supermicro Server with motherboard X7DB8, chipset Intel 5000P, Xeon 5050 Digium TE110P Software --------------------------------------------- Asterisk version 1.2.12.1

I've read as much as I can on this error and still can't seem to figure out what's causing this error: Jun 23 20:54:58 NOTICE[7483]: chan_zap.c:7395 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Jun 23 20:55:03 NOTICE[7483]: chan_zap.c:7395 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Jun 23 20:55:03 NOTICE[7483]:

Hi, I am facing problem in configuring D-channel. I did the following configuration for TE-120P card /etc/zaptel.conf span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 /etc/asterisk/zaptel.conf group=1 signalling=pri_cpe switchtype=euroisdn context=incoming channel=1-15,17-31 DIGIUM card is connected through cable to another end.On placing call from other end to

Hello I just installed a TE110P in a Dell Poweredge 750 (rackmount), which is connected via crossover T1 cable to a adit 600. Anyway, I've encountered an array of errors, which I believe I have narrowed down to the 22 IRQ misses I encounter on zttool. I've noticed that the te110p and the usb device share an IRQ. Could that be the source of my woes? Would disabling the usb device in the

Just upgraded to most recent CVS and now I get this: pri_dchannel: PRI Error: We think we're the CPE, but they think they're the CPE too. when starting asterisk. Needless to say, I can't run asterisk without my PRI. Guess I'll start reverting code backwards day by day until I find the code that works. -Matthew

I am trying to connect two machines to each other with an T1 crossover cable. The first machine has two TE120P cards - one connecting to the telco on an ISDN PRI. The second to a crossover T1 cable to a second machine which has one TE120P card. Telco <-cA-> Machine1 <-cB-> Machine2 Machine1: Two TE120P cards Machine2: One TE120P card cA: Standard T1 Cable cB: Crossover T1

Greetings to all, I am getting the following error on my PRI-connected Asterisk box, and am just wondering if anyone else has seen this, and if so how they solved it. Jan 18 10:10:23 NOTICE[6070]: chan_zap.c:7428 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 Jan 18 10:10:24 NOTICE[6070]: chan_zap.c:7428 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary

Hi all, So, we reverted the LibPRI version and tested it, and then tried with the latest version of everything. Still no changes. The BRI line is in PTMP. If we set the configs to PTMP in the genconf_parameters and try it, we get the following: [Jan 21 17:32:20] ERROR[20341]: chan_dahdi.c:12645 dahdi_pri_error: Unable to receive TEI from network! If we set it to PTP (which it is not) we

Does anyone have any experience ith configureing the sangoma A102 card for testing using a e1 cross cable i've configured and installed the cards properly even the lights on the card are green which proves that my cross cable is properly built too. my problem is with asterisk which gives me these errors PRI got event: HDLC Abort (6)on Primary D-channel of span 1 PRI got event: HDLC Bad FCS

Hello everyone, We have recently turned up a new T1 from McLeod (Midwestern CLEC). It is configured like so: /etc/zaptel.conf: loadzone=us defaultzone=us span=1,0,0,esf,b8zs ;(also tried 1,1,0,esf,b8zs) bchan=13-23 nethdlc=1-12 dchan=24 /etc/zapata.conf: switchtype=national context=pri-in signalling=pri_cpe group=1 channel => 13-23 I can get hdlc0 (and pvc0) up just fine after the

Dear All, I'm integrating avaya commuication manager difinity ver 1.0 with asterisk using B2B E1. following are the details of my H/W, zaptel configs and software installed. Digium TE110p asterisk 1.2.19 cent OS 4.4 zaptel 1.2.18 libpri 1.2.4 etc/zaptel.conf span=1,0,0,cas,hdb3 bchan=1-15,17-31 dchan=16 when i ztcfg -vvv im having this error message and the E1 is not getting up. "cas

This afternoon I finally figured out more with regarding to a strange clock-slip problem we have on our asterisk box. We have two TE410s, in E1 mode: TE410P version c01a009b They have their own interrupts: 66: 781648298 783747388 IO-APIC-level t4xxp 233: 253890977 1311504670 IO-APIC-level t4xxp They have their full 31 channels: span=3,0,0,ccs,hdb3,crc4 bchan=63-77,79-93 dchan=78