similar to: TE410P <=> Dialogic D/240SC-T1

We have (10) Dialogic D/240SC-T1 REV 2 voice boards. Prefer single buyer, take all (10) for $675/ea Cory Andrews ***************** b2 Technologies 454 Sonwill Drive Buffalo, NY 14225 ***************** voice: 866-44-B2TECH X22 fax: 716.630.1548 email: sales@b2llc.com

Maybe of you guys know the answer to this: We have T1's that come from both MCI and Global Crossing as channelized (24 Ports per T) with inband (DTMF) delivery of ANI and DNIS (format = *DNIS*ANI*). My old equipment was set for D4, AMI, SF and Wink Start and so is Asterisk. I've moved these T's to Asterisk TE410P and inbound calls are arriving to external voice mail system

I'm a bit confused about how to handle this. I have Asterisk sitting in the middle between a Qwest Long Distance T1 (Voice T1, D4, SF, AMI) and an external voice mail PC using a Dialogic D/240SC-T1 card. The Qwest T1 originally was connected to the Dialogic card directly. The signaling was set to E&M Wink Start because Dialogic used this as its default settings, so it just worked

Hi, I'm trying to connect a PC with a TE410P to an E1/IP equipment. Unfortunately I keep getting a yellow alarm from zaptel (in zttool) and a Loss of Framing alarm on the remote equipment. The E1/IP is connected on the other side to a PRI interface on a GSM MSC. I have configured the span as: span=1,1,0,ccs,hdb3 (also tried span=1,0,0,ccs,hdb3) and the channels as: bchan=1-15,17-31

I'm trying to install a TE410P this is what happens with compiled zaptel 1.0.9, 1.2-beta and 1.0.9 from http://updates.xorcom.com/iso/ this is my zaptel.conf (checked with the provider the values): span=1,1,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 loadzone=it defaultzone=it then I modprobe wct4xxp debug=1 t1e1override=15 and the kernel says : Sep 30 16:12:40 localhost kernel: Zapata

Hello I've got small PBX (30 simultaneous connections) based on asterisk (1.6.2.6), which uses Stargate 2N ISDN to GSM gate. It runs ok for day or two, but then I get: dahdi: HDLC Receiver overrun on channel TE4/0/1/16 (master=TE4/0/1/16) in my kernel logs, in asterisk i get: pri show spans PRI span 1/0: Provisioned, Down, Active PRI span 3/0: Provisioned, In Alarm, Down, Active (span 3

Basically, have an old IVR application running under Apex's Omnivox software on a box with 4 old intel dialogic D240SCs, and would like to allow remote clients to gain access to aforementioned IVR application via softphone, 7960, ata, etc via asterisk with a TE410P. Unfortunately, all I know about the dialogics is that they're configured for D4/AMI, which I believe I have configured right

Maybe one of you can help me with this: We have T1's that come from both MCI and Global Crossing as uses channelized (24 Ports per T) with inband (DTMF) ANI and DNIS delivery (format = *DNIS*ANI*). My old equipment was set for D4, AMI, SF and Wink Start and so is Asterisk Server. I've moved these T's to Asterisk TE410P and inbound calls are arriving to external voice mail

Maybe of you guys know the answer to this: We have T1's that come from both MCI and Global Crossing as channelized (24 Ports per T) with inband (DTMF) delivery of ANI and DNIS (format = *DNIS*ANI*). My old equipment was set for D4, AMI, SF and Wink Start and so is Asterisk. I've moved these T's to Asterisk TE410P and inbound calls are arriving to external voice mail system correctly

TE410P card down. I have three (3) TE410P in one machine running asterisk with SS7. My problems started last week when one of my cards started switching to E1 every time after reboot. I set the following in dahdi.conf and that solve the problem. /etc/modprobe.d/ options wct4xxp t1e1override=0x00 Now all 4 ports on that card is down with Red Alarm. I tried rebooting the machine and

Hello all Asterisk Users, This is my first post here. We are in a process of moving Dialogic 240/JCT-T1 from old voicemail server to Asterisk box. Which card drivers do we need? Please share experience if anyone have successfully configured Dialogic JCT-T1 card with asterisk? Only source proves that this card work with * http://lists.digium.com/pipermail/asterisk-dev/2003-April/000244.html

I'm a bit confused on how to setup Zaptel.conf and Zapata.conf when there is a TDM400P and a TE410P installed after upgrade. The TDM400P has 2 FXS in position 1 & 2 and 1 FXO in the fourth position. I see boot, WCT4xxP loading first and WCFXS loading second. According to my understanding, given above, the TE410P should be configured first, then the TDM400P. However, I'm not sure

I have a box with 12 T1s (4 Te410P cards). The PSTN provider is reporting slips and ask me to update the clock source. I have my system.conf set as the following but when I run dahdi_scan only the ports on Card 1 are showing up with syncsrc=1 system.conf : span=1,1,0,esf,b8zs bchan=2-24 mtp2=1 span=2,2,0,esf,b8zs bchan=26-48 mtp2=25 span=3,3,0,esf,b8zs bchan=49-72

Hi, after loading the zaptel driver wct4xxp I have strange log lines in the syslog: Out of storage space. free tells, that more than 900 MB are still free. Disk space is also available. I'm using a dual opteron in 64 bit mode. Any ideas? Roger. Syslog: Dec 1 02:18:37 ipphone4 kernel: TE410P: Launching card: 0 Dec 1 02:18:37 ipphone4 kernel: TE410P: Setting up global serial

Dear All, we have installed a TE410P card on a Dell Poweredge 1750 running a slackware 10 with 2.4.26 Kernel. Then we have made two loops on the card and we have configurated all the 120 channels. Our goals was to perform some stess tests even if in this scenario we used the same box as generator and target. The stress test comprised to generate up to 60 calls at the same time by placing a file

Hi, I am about to pull my hair out after trying to get our PRI up and working. We are switching from a Cisco gateway to an Asterisk box which provides the 23 phone lines for our office. So, because the Cisco gateway is working I can assume I have all the settings right (b8zs, esf, dms100, etc) and the PRI is live (because we are switching over). When dialing from PSTN, I get busy signal. When

Hi, I'm trying to bring up two PRIs from qwest with asterisk and dahdi. I'm using an OpenVox D410E and the drivers are loaded. My system.conf looks like this: # Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" B8ZS/ESF RED span=1,2,0,esf,b8zs bchan=1-24 # Span 2: TE4/0/2 "T4XXP (PCI) Card 0 Span 2" (MASTER) B8ZS/ESF RED span=2,1,0,esf,b8zs bchan=25-47 dchan=48 These

Dear members of the list, I have difficulties to obtain sync with a Digium TE420 PCI Express For four entries E1, In my case I am with only 3 E1s available to configure. The telephony operator is BrasilTelecom and Signaling is R2 Digital. The information I have is that are E1s with 32 channels, not have sure. My settings Have been based on the link reference:

I keep getting a red alarm when trying to setup asterisk to use my TE420B EC. I only have a blank context setup in my extensions.conf as I haven't started to config that until I can clear this red alarm. I don't have physical access to the server, so I can't go reseat the modules/card/ethernet cable, though I have hands on location that have done this a couple times

My telco used cat5 as well for the demarc to CPE. It's also with noting that many channel banks, such as my Atlas, and zapata.conf itself also have parameters to allow you to tune the gains to compensate for cable signal loss. I've never had to touch them, and my CPE is about 300 feet from the PRI demarc (with an ordinary Cat5 cable connecting them)