similar to: Legacy PBX integration

Most people seem quite positive about Snom phones, I cannot share this opinion. The displays are dying quite often, and firmware is buggy. I have tried every firmware from 4.5 up to 5.x and 6.04 but keep having problems with phones locking up or rebooting during an ongoing conversation. REALLY annoying for a phone that is advertised / targeted as a business class phone

Hi list! I'm sure the topic has been discussed but I could not find what I was looking for. What would be the best / easiest VPN software solution. I would like to install vpn software on the * server for roadwarriors to connect to with laptops running windows. Ideally the vpn solution will not require any additional software on the client side but will use IPSEC. (Ofcourse call quality

Hi list! I have some sip phones and Sipura ATA 2000's. However after dialling a number I need to dial a # to control a device. When I dial # Asterisk kicks in and puts the call on hold. How can I change this? Thx!! Remco

Is it possible in any way to use an Outlook contacts database as the source for the internal Asterisk database that is used for callerid lookups? Thanks!

Hi list ! Is it possible to show the used Useragent of a peer that registered with Asterisk? It's being saved obviously because the console says so when a phone is registering but sip show peers doesn't show it? Is there any other way to view it? Thanks!

Hi! I'm trying to setup a Wildcard TE110P with a PRI in The Netherlands. I get a Red Alarm on the line. Is there any way of debugging this? I've tried some configs that should work but without success. Is there any way of telling if the cabling is correct or what else the problem could be? Thanks!! Remco

Hi list! What exactly is the meaning / function of the pridialplan & prilocaldialplan? I've been trying to find out what the different possibilities for these settings are but couldn't find a clear answer. The possible parameters I could find are are : local,unknown,dynamic,national,international and maybe there are more? Thanks!

I installed bristuff0.20-RC3 (which includes * 1.0.3 stable) It works fine until I disconnect the phone jack for the ISDN line. Even after plug it back in asterisk still reports that it could not create a zap channel when I try to dial out and the line gives an engaged tone when I try to dial. Re-starting asterisk doesn't solve this, I have to stop asterisk, unload the modules, reload

Hi list! While looking for the Snom 190 I found another phone, the Elmeg IP 290 (www.elmeg.de). Looking at the pictures & the specs they seem to be very similar beasts but the firmware is supposedly not interchangeable. Does anyone know the difference between the 2, do they work with Asterisk? The weird thing is that Elmeg has similar phones with the Snom look but they are ISDN only (no

Hi List! I installed Asterisk 1.0.3 stable on a RHEL rebuild. Due to problems with * modules refusing to build I replaced the RHEL kernel with stock 2.6.10. Asterisk seems to be working but when I dial voicemail I hear nothing. When I hangup I see a message on the console that the calller did not specify a mailbox number so I guess voicemail app is working. The phone(Grandstream BT100) is

Hi list! Sorry for this slightly off-topic message but does anybody know if the standard for ISDN BRI is the same in Spain as it is in the rest of Europe (or the Netherlands). Will a standard HFC-S card work?

Hi list! I have some strange problems with Asterisk 1.0.5-BRIstuffed-0.2.0-RC5. Very regularly asterisk seems to lose connectivity with the ISDN line. If you try to call in you get the information tone that the number is not in use. Outbound calls do stil work however. Unloading the modules and reloading them and start/stop asterisk will solve the problem. Another problem that occurs

Hi, Snom phones firmware 5.0 is now out. Try it if you like: http://www.snom.com/wiki/index.php/Main_Page. Regards, --------------------------------------------------------------------- Usman Tahir snom technology AG www.snom.com --------------------------------------------------------------------- -------------- next part -------------- An HTML attachment was scrubbed... URL:

Is it possible to rewrite caller id's? I would like to have sip phones appear by their local cid (like Henk <208>) but when they call out using the PRI I would like their full DID (MSN) to appear (like 0031201234567) I could ofcourse set callerid to the main phonenumber but surely there must be a better solution? Thanks!! Remco

I tried to get callerid working the normal way but the cid is never passed to the phone. It doesn't work untill I set SetCIDNum(0${PRI_NETWORK_CID}) in extensions.conf which I found in the wiki: http://www.voip-info.org/tiki-print.php?page=Asterisk+zaphfc Is this intended behaviour, or still a bug? It does work but it only shows one zero even though I have nationalprefix = 0

Hi list! I'm using Asterisk 1.2.7.1. with FreePBX 2.0.1 on a CentOS 3.7 box. On the * box I also have a samba share where our CRM app can dump call files and a cron script is moving the call files every second to the asterisk directory. Everything goes really quickly, the call file is placed on the samba share and very quickly moved to the asterisk dir, so far so good. But then the call

Hi list! I'm currently using a HFC-S card for my ISDN BRI line with bristuff. The instability is driving me crazy however. I'm having continuous problems where inbound calls will not work after some time of operation (the number then appears as not in use to the caller) or also outbound calls do not work. The solution is to unload the modules, stop asterisk, re-load the modules and

Hi list! I am installing an * box that will be installed on a site with KPN BRI ISDN in The Netherlands. I am using bristuff fron Junghanns. Does anybody know the correct settings for this? I will not have internet access there which makes it harder to google around on location. switchtype = euroisdn is pretty obvious but what about these settings: signalling = bri_cpe_ptmp ; p2p TE mode

Hi list! I have a strange echo problem. Two days ago I setup * 1.0.6. at a friend of mine. Just an * server and for outbound calls wengo.fr was used to place calls via sip. He had a strange echo on the line I didn't experience on my setup. Today I upgraded my asterisk 1.0.5 to 1.0.6 and suddenly I have an echo too on sip calls thru wengo!! I already verified wengo was not the source of

Hi list! I'm still trying to figure out about the groups in asterisk. If I understand correctly, if you assign a certain group number and you assign the same call group number to a sip device the device will reing even though you did not specifically specify it in extension.conf? How will this work for ISDN BRI/PRI? I don't want some extensions to get all calls from the BRI/PRI, just