similar to: TE110P errors

Hi, This error I got it just when I gonfigure zaptel support isdneuro 31 channels. But if I configure zaptel to support T1 and just 24 channels I have no problem. ######################################################################## #### # # Zaptel Configuration File # # This file is parsed by the Zaptel Configurator, ztcfg # # loadzone = it span=1,1,0,ccs,hdb3,crc4 bchan=1-23 dchan=16

Hello, I am trying to get a Wildcard TE110P to work in a relatively modern HP Proliant DL385p Gen8 server. Being a potent 12 core Opteron server I expected no problems. Much to my dismay the dahdi_test results are constantly terrible: # dahdi_test Opened pseudo dahdi interface, measuring accuracy... 89.101% 89.195% 89.142% 88.957% 88.953% 89.115% 89.089% 89.134% 89.066% 89.021% 88.933% 89.044%

i get this message with a red signal on TE110P card: ***************** TE110P: span configured for... Calling startuo (flug is 4099) wcte1xxp: Setting yellow alarm ***************** what does mean ? thank you :)

Hi, I am struggling to get rid of a conflict on DELL 2800 : PCI Parity error (EB113 on the display) I am learning linux and asterisk as I go along, there might be obvious things I should know, but bear with me. >From demsg below my 2 digium cards installed are listed (no config or connections done to digium cards yet), the conflict is with the TDM400P card, without that card, in any slot, no

Hi all, I?ve ran into a problem regarding D-channels. I have setup Asterisk (CVS-HEAD-03/21/05-16:41:57) on RH Fedora Core 3(2.6.10-1.770_FC3) I also have a digium wcte11xp card for connetivity to the PSTN(E1). When I start zttool i see that Current Alarms changes between Recovering and Blue Alarm/Recovering. I started to see these problems after i moved the digiumcard from one PCI slot to

Hi everyone I have a Digium card TE110P and after plug it, turn on the computer and configure, the LEDs don't light up in spite of what Digium FAQ says about the LEDs: When will the LED's light up on my TDM400P/TE110P/TE2XXP/TE4XXP? ... The TE110P LED's will light up RED when the span is configured and kernel module is loaded. If configured correctly and a circuit or channel bank is

Hi I'm having difficulties getting up my TE110P (running as a E1) when I connect it to the PRI. If I start the server with a loopback connector everything seems fine and the led is green but when I connect it to the PRI the flashing starts .... I can't seem to find anything in the log that suggests what could be wrong .....Aug 8 11:33:00 DEBUG[1369]: Updated conferencing on 31,

Hi all, I'm sure something similar has been discussed, but one can only wade through the archives for so long. I'm setting up a T1 and my telco has a bunch of questions it wants me to answer. I know much of the TE110p is configurable to do any of this, but I wanted to know if there is an optimal or preferred setup. Any help would be appreciated. Here is the quiz my telco is giving me:

Hey there, What recommendations does anybody have as to motherboards known to work well with the Digium TE110P T1 interface cards and the TDM400P analog POTS interface cards? We currently make use of the TE110P for our T1 (esf w/ b8zs - not a PRI) and have experienced many issues caused by our PBX's motherboard. Additionally, we built a server to become our new PBX, but that machine runs

Hi all, I'm sure something similar has been discussed, but one can only wade through the archives for so long. I'm setting up a T1 and my telco has a bunch of questions it wants me to answer. I know much of the TE110p is configurable to do any of this, but I wanted to know if there is an optimal or preferred setup. Any help would be appreciated. Here is the quiz my telco is giving me:

Hi, I have some problem to get this setup working. I have a CAC Channel Banl I, with FXO and an Asterisk box ( I am using Asterisk@Home 1.2) and I have a TE110p installed in this box. What I want to do is, just to be able to dial one of those lines that already are connected to the channel bank, and transfer that call through TE110p and Asterisk to a user agent somewhere through Internet.

Im using a TE110P as a trunk to a Panasonic KD-500 everything works well.....but Im having this problem where one of the channels becomes blocked with a partial phone number after about two days. So if the channel that becomes blocked is channels 23 no calls can get in. If the channel that gets blocked is 22 then one call can get in. The only way to clear this is to reboot the server. This

We are currently working to trunk from a Nortel 81C to an Asterisk Server 1.4 running on Red Hat Linux. We have two PRI trunks which work with the exception of the clock slips, which is causing the Nortel to reset the PRIs once a hour. Thanks for any suggestions. 81C MSDL Asterisk Digium TE110P REQ prt TYPE adan dch 10

My TE110P reset some times in the day. E this cause an interruption in the service. How I decide this problem? my zaptel.conf span=1,1,0,esf,b8zs bchan=1-23 # set this to 1-15,17-31 for E1 dchan=24 # set this to 16 for E1 defaultzone=us loadzone=us my zapata.conf [channels] language=en signalling=pri_cpe switchtype=national echocancel=yes echocancelwhenbridged=yes echotraining=200 ; Asterisk

Running Asterisk 1.2.9. I just installed a TE110P card and configured zaptel.conf & zapata.conf. The config files look right to me but I'm getting the following error when trying to start asterisk: Asterisk died with code 1. Automatically restarting Asterisk. Does anyone have any idea what is wrong with this configuration?? Thanks in advance!!! Here's my config files: zaptel.conf

Hi All, I have configure my Asterisk as follow (using Asterisk@home): [zaptel.conf] span=1,1,0,ccs,hdb3,yellow bchan=1-15,17-31 dchan=16 loadzone = uk defaultzone=uk [zapata.conf] [channels] switchtype=euroisdn pridialplan=local prilocaldialplan=local internationalprefix=00 nationalprefix=0 usecallingpres=yes busydetect=no ; not need on pri callprogress=no ; was yes but wiki says experimatley

I'm installing TE405P card. This is my zaptel.conf. -------------------------------------- span=1,0,0,ccs,hdb3,crc4 span=2,1,0,ccs,hdb3,crc4 span=3,0,0,ccs,hdb3,crc4 span=4,0,0,ccs,hdb3,crc4 loadzone = us defaultzone= us -------------------------------------- When i modprobe wct4xxp, -------------------------------------- PCI: Found IRQ 11 for device 02:0b.0 PCI: Sharing IRQ 11 with

I guess it is possible to have an HFC-S card and a Digium TE110P card working at the same time? The TE110P will work in E1 mode. I think the zaptel.conf is probably right but the zapata.conf not (I just tacked on another group at the end but I don't really know what I am doing). Can anyone help? ----------------------------------------- My zaptel.conf looks like this: # hfc-s pci a span

Dear users. My current setup uses a euroISDN E1 with 8 cahnnels for incoming and outgoing calls from a digium te110p. Currently all phones use SIP. However, I need to add some faxes lines and some POS credit card machines. These will require POTS lines with a fixed DDI. I have purchased the tdm400p and 4 FXS modules. My problem is with the zaptel.conf and zapata.conf. I am a little confused as

Hello, I'm using asterisk for a while, fully ip, and i'm now moving to ISDN, so i got a TE110P. The first problem is the "Unexpected Channel selection 3" message. I'm unable to find, on the web, the meaning of such message. Can somebody explain me? My second problem is when a call come in, and hang up. Asterisk shows " -- B-channel 0/31 successfully restarted on