similar to: FXO without answer supervision

Hi all, i've installed AMP and Asterisk following the INSTALL file and i have a problem with the TDM04B with 4 FXO: [root@srvoip ~]# ztcfg -vv Zaptel Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Slaves: 01) Channel 02: FXO Kewlstart (Default) (Slaves: 02) Channel 03: FXO Kewlstart (Default) (Slaves: 03) Channel 04: FXO Kewlstart (Default)

Hi I have been having a rough time getting a Sangoma A200/Remora FXO/ FXS Analog AFT card set up properly. The main issue is that the card has four ports and as far as I can tell Asterisk is only seeing two. On the two that it recognizes the "Green" FXS ports are not green, they just are not lit. The "RED" FXO ports are indeed red, but from what I have read your not

Hi everyone, I've just got my X100P card installed and working but there seems to be an issue with hang-up supervision. If I stuff a call out over the X100P card onto the PSTN that's fine. When I hang up the SIP phone the PSTN call ends. If I receive a call from the PSTN, it's answered and everything is ok until the remote party hangs up. Asterisk thinks the call is still active and

Hi: I had an fxo card from Digitnetworks and it was working fine on my Asterisk box. I then replaced it with TDM04B. I changed the zaptel and zapata to include the four channels. When I run ztcfg, I get configuration errors: Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) Channel 03: FXS Kewlstart (Default) (Slaves: 03) Channel 04:

I just purchased a T100p from digium and a Carrier Access Access Bank 1 channel bank (12fxs/12fxo). I have the setup partially working thanks to some help from IRC. However I still have the following issues I can't seem to resolve 1. When calling into the system from the PSTN call hangup is not detected. * leaves line in use until it is shutdown. 2. When calling an analog phone connected to

Hi all, I bought a Sangoma A200 card from an online supplier and explained exactly what I wanted, 3 incoming phone lines to PBX and a life line (some where to connect a standard BT phone to the PBX incase the power goes, making the BT phone ring). I was told to order 1 x FXS module (2 FXS ports) 2 x FXO modules (4 FXO ports) However being a complete noob, I have connected the 3 lines to the

As far as I can tell, after discussing this matter with other asterisk users in my area, my telco _does_ provide disconnect supervision.. It seems that the problem is actually related to the Sangoma A200 card I'm using, as two other people both using this same card have expressed the same problem.. Are there any other users on this list using the Sangoma A200 FXO port card, and experiencing

Hi, I am using TDM400 card with 3 fxs and 1 fxo. I am struggling to detect hangup tone or disconnect supervision tone from my CO. I attached the recorded wav file which contains my telco's disconnect supervision. I am using , asterisk-1.4.33.1 dahdi-linux-complete-2.3.0.1+ 2.3.0 OS => Debian-lenny 5 users.conf ------------- [trunk_1] trunkname = pstn ; GUI

Does anyone have disconnect supervision working on their TDM400P or X101P cards (to/from the telco)? Googling "telco disconnect supervision," I found the following description: http://mirror.lcs.mit.edu/telecom-archives/telecom-archives/TELECOM_Digest_Online/1559.html [cut] Re: How Do I Get "Kewlstart" From my Phone Company? Paul A Lee Tue, 24 Aug 2004 16:58:16 -0400 ... It

I had a working Asterisk 1.4.24.1 installation on SUSE 9 Linux but SIP only. I then downloaded and installed latest Zaptel and could not get Zaptel working. So I downloaded Asterisk again and re-installed. But still problems: Here is my ztcfg output: asterisk:/etc/asterisk # ztcfg -vvvvv Notice: Configuration file is /etc/zaptel.conf line 4: Unable to read Zaptel version information. Zaptel

Hello, I am trying the setup the TDM01B card. 1 FXO. I connected it to a regular home line. in the /etc/zaptel.conf, I have fxsls=4 In the /etc/asterisk/zapata.conf I have: signaling=fxs_ls language=en group=1 context=default channel => 4 When I start asterisk, I get this error: ERROR[10376]: chan_zap.c:6584 mkintf; Signaling requested on channel 4 is FXO Loopstart but line is in FXS

Been using a few different FXO interfaces (X100P, Voicetronix, and SPA-3000) at a couple sites and they've all run into nasty issues at times. I'm looking at moving one of my offices and am in the market for a solution for connecting 4 FXOs. I got excited about recent offerings from Digium and Sangoma in the way of new cards but I hear they're causing troubles for more than a few.

Hi all, I have a problem with the cvs head zaptel library: I cannot update my zapata.conf into asterisk when I issue the reload command from the CLI prompt; only when I stop and restart the asterisk service. The system sends the following message: Jun 20 09:49:14 WARNING[3754]: chan_zap.c:10364 setup_zap: Ignoring switchtype Jun 20 09:49:14 WARNING[3754]: chan_zap.c:10364

*** Now you just need a "phone" or "station" (FXS) device and a method of connecting it. *** So... essentially I need to spend another $125 US on a Wildcard TDM400P so I can plug in an analog phone? On the X100P description it says: "The X100P supports FXS Loopstart and "Kewlstart" (Loopstart with far end disconnection supervision). It can detect ringing and

Ok so this is officially driving me crazy. I have an Asterisk 1.6.1.6 install with DAHDI/DAHDI tools (latest) and an OpenVOX TDM400 card with 1 FXO port and 1 FXS port. I have a POTS line from my phone company attached to the POTS line. I have asked for "disconnect supervision" to be provisioned on my line and they claim to have added it. However, my scenario is as follows: I receive a

FYI... Just installed one of the new Sangoma A200D analog pstn cards with the hardware echo canceller on a trial basis. The card has four fxo interfaces. Excellent audio quality, excellent echo cancelling, and excellent audio levels. The four pstn lines at this location are rather long analog loops that have rather long echo trails. I started with a pair of x100p's a couple of years ago,

Hello All, I've mostly solved my DID problem from a few days ago. Apparenly the lines weren't configured properly. Now heres the next question. 12 E&M wink lines from telco. I have them all plugging into an Adtran 750 with FXS cards. The Adtran ports are configured DPO. How do I signal this from Zaptel. I have them setup E&M in zaptel.conf and EM_W in zapata.conf. They

Can anyone help me with the term that SBC uses to refer to disconnect supervision? I have an Adit 600 channel bank which has helped improve the disconnect detection time down to about 8 seconds. This is still causing some issues in particular with call progress enabled in * we are having a few disconnects while calls are in session (about 2 reported in first 5 days of use). I have talked both to

so i have been running v1-0 on all of my test boxes for about a month now testing iax/sip/res_xxx. I decided to put it into production so I updated a box that was running 0.9.? that had been working perfectly for months and low and behold the inbound line from telco now intermittantly doesn't clear and none of the other channels can dial out on that line. I have tested the line in this

I have a bit of a weird problem that I'm having great trouble debugging. I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID, which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS. Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls. My