Displaying 20 results from an estimated 800 matches similar to: "pstn to asterisk, DVG-3004S, MP104?"
2005 Oct 05
1
DLINK DVG-3004S
Does anyone have any experience using this DLink quad FXO <> SIP
gateway with Asterisk? I'm still looking for an analog interface that I
can live with, having tried X101p, SPA-3000 and TDM400...all with less
than desirable results.
Michael
--
Michael Graves mgraves@pixelpower.com
Sr. Product Specialist www.pixelpower.com
Pixel Power
2006 Mar 19
7
An FXO version of IAXy?
Hello--
In the interest of Symmetry, does anyone else in the world see any need
for a device like the IAXy (or the SIP ones from other manufacturers,
like the ATA186), but one that presents an FXO interface instead, so it
can be connected not to phones, but the PSTN?
murf
2005 May 10
0
Flashing DVG-1120M to DVG-1120S
So, I recently acquired an old DVG-1120M that was previously used with
AT&T CallVantage service. It currently uses MGCP.
I see online that there is a SIP version out there (DVG-1120S), which is
essentially a DVG-1120M reflashed with the SIP firmware and the 'M'
scraped off in favor of an 'S'. I've also seen people on this list
saying that they flashed their M with S
2004 Sep 05
1
need help configuring dlink dvg-1120M
Hi,
I have a dlink dvg-1120M (mgcp) box that i will like to use with
asterisk. Is it possible? has anyone done that?
Here's a link to the product page at dlink.
http://support.dlink.com/products/view.asp?productid=DVG%2D1120M
Also, does anyone has or know where to get the firmware for Dlink
DVG-1120S (sip model)?
thanks.
--
Zahid
2005 Mar 11
1
DVG-1120 questions
I upgraded a DVG-1120M to a DVG-1120S. Everything works great, but I'm
having some caller ID issues on incoming calls sent to the SIP device.
Using debug on the device, the caller ID looks fine - just as I set it in
Asterisk. However, the phone is showing "CID TRANSMISSION ERROR". Should
I check the RX and TX gain levels? Try another phone? Any ideas would be
much appreciated.
2004 Jun 16
0
D-Link DVG-1120M and *.
Thu, 06 May 2004 12:31:33 -0500 there was an e-mail to the list from
Isaac McDonald suggesting to re-flash the DVG-1120M gateway with the
DVG-1120S code to have the gateway login to *.
I have been looking and can seem to find the flash code. D-Link tech
support doesn't know much about the box.
Any sources for the TFTP file would be appreciated.
Once this is running SIP will I need the xml
2004 Oct 05
1
Dlink DVG-1120 Linksys PAP2 any Good?
I had just found a Dlink DVG-1120 on ebay and I'm curious if anyone has
used you it with asterisk. They were only $65. I have tested with the
Linksys Pap2 and found that box to be fairly nice except for a lot of
backgound/white noise. I was wondering if any else had experienced
that? Let me know if I've wasted $65 on the Dlink and also if you had
similar experience with white noise on
2004 Apr 29
2
Dlink DVG-1120s and Asterisk
I friend gave me his DVG-1120s after he realized that AT&Ts callVantage
stuff would not work for him. It appears to be running a SIP version of
firmware, however, it downloads an XML configuration file via SSL from AT&T.
I cannot find a way to manually configure the VOIP portion of the unit via
the GUI.
I contacted D-Link to get an example configuration file so I could get it
working
2005 Mar 19
0
DVG-1120S no call display name and time
Hi,
I am having problems with callerid name and the time with my
dvg-1120S. Every time I receive a call, it reverts the phone to
January 1st 12:00am. I've looked everywhere in the browser and telnet
configuration to change this.
Also, it never shows the name of the caller. I've even tried forcing
the caller id info using SetCallerID, but it still doesn't show the
name.
Any
2005 May 27
0
DVG-1120S does not show callerid Name and resets time
Hi,
I am having problems with callerid name and the time with my
dvg-1120S. Every time I receive a call, it reverts the phone to
January 1st 12:00am. I've looked everywhere in the browser and telnet
configuration to change this.
Also, it never shows the name of the caller. I've even tried forcing
the caller id info using SetCallerID, but it still doesn't show the
name.
Any
2006 Nov 06
0
TrixBox and MP104 FXO (AudioCodes GW)
I'm trying to connect this FXO GW without any success
1) I had to configure the " " to "allow any SIP to connect , so there will be a connection. afte that when I'm dialing I get a noise. I read on the internet that I have to change the impedance (?)
2) I could not find any HOWTO configure this combination - I read that it is a lot of pain to configure the Mp10x but than
2007 Dec 13
3
OpenSSH patches for Mac OS X
OpenSSH Unix Dev,
Mac OS X 10.5 recently shipped with OpenSSH 4.5p1. This build
includes a number of patches, some general bug fixes and some platform-
specific fixes and enhancements. These patches are available from our
open source site (http://www.opensource.apple.com/darwinsource/10.5/OpenSSH-87/
).
Following is a brief description of each patch. We'd be more than
happy to
2007 Jul 23
0
CAS signalling and FAX solution
I am trying to solve the fax problem by installing an E1 channelbank
(Megaplex MP-104)
It's a box that has 8 x FXS ports and a single E1 port.
The plan was to use one of my 4 E1 ports to connect to the Telstra
onramp and one to the MP104. I have since discovered however that the
MP104 only supports CAS signalling and I am having trouble getting
asterisk to work in this mode.
Currently we
2004 Aug 02
1
asterisk call parking + SNOM lighted buttons?
I'm trying to get call parking working with the lighted buttons on the
SNOM 200. I have set the 5 buttons to "Park Orbit", for extensions 700-704.
Pressing the first button (x700) does park the call. However, the
remaining buttons (x701-704) don't allow me to pick up parked calls, or
show parking status via the LEDs. I can only pick up parked calling by
manually dialing the
2009 Nov 24
2
audio cuts out during IVR
Hi all,
I'm running 1.6.2.0-rc6, and I'm running into a problem: sometimes the
audio vanishes in the middle of listening to an IVR background prompt.
This happens with both analog (Digium card) and IAX2 incoming calls.
The prompts are stored in ulaw format (and the IAX2 calls use ulaw).
The asterisk console claims that the IVR prompts are proceeding in the
expected fashion, but I
2006 Jan 19
0
AudioCodes Unreliable DTMF Detection
We're trying to use some AudioCodes MP104 FXO units as gateways to
Asterisk but cannot get them to reliably detect DTMF. Some landline
calls get most digits but some are duplicated. Some cell phone calls get
0% DTMF recognition.
Anyone with experience with these units have any suggestions? ABP
Technical Support has been unable to diagnose the problem and is now
sending random guesses and
2007 Apr 19
1
AudioCodes MP-104 MGCP?
Greetings;
We are trying to get Asterisk up and happy at our site-we tried VOIP
using Sphere about a year ago, spent a *boodle* on expensive hardware
and services from a local "expert", but it never was happy.
I'm brand-spanking new at VOIP, and I've learned a *ton* getting
Asterisk breathing in the last couple of days. I have three Polycom
Soundpoint IP 500 SIP phones, which
2008 Oct 02
2
rebooting snoms in 1.6
With Asterisk 1.4 I could use commands like:
/usr/sbin/asterisk -rx "sip notify reboot-snom mjc_home"
to reboot a snom phone. Now, with 1.6, when I try that, I get:
Unable to find notify type 'reboot-snom'
Command 'sip notify reboot-snom mjc_home' failed.
Do I need to add some magic to sip_notify.conf? I haven't quite figured
out how to make it work.
- Mike
2006 Feb 20
1
call parking "hint"
Hi,
Is it possible to use the hint priority to allow call parking slots to
be monitored on (for example) Snom indicator lamps? How do you refer to
the slots (i.e., what is the "channel") in the hint?
- Mike
2006 Mar 10
2
IAX2 + Sonicwall
Hi all,
I currently have an Asterisk test server behind a TZ170 Sonicwall
firewall / NAT box, with several DIDs.
I've found that inbound IAX2 calls don't work reliably (i.e., I get a
busy tone) unless I enable "Use Consistent NAT" in the Sonicwall. This
feature is poorly documented by Sonicwall, so I thought I'd pass it along.
Has anyone else run into this, or figured