similar to: Australian E1 from Optus still not working

Displaying 20 results from an estimated 1000 matches similar to: "Australian E1 from Optus still not working"

2006 Feb 28
2
incoming calls dropout on PRI over TE110p
I am running Asterisk 1.0.9 and have been running all my calls through a VSP over a IAX2 trunk however we have recently purchased and connected a TE110p to a PRI ( E1 with 16 voice channels ) through Optus. I can make outgoing calls via it fine, however incoming calls are dropped after a few seconds ( or as soon as a command like Playback, or the call is picked up if forwarded to a SIP
2004 Sep 22
3
Optus Australia Multiline SHDSL service
Hi, I am currently trying to find a replacement for a dinosaur PBX and want to replace it with a VoIP solution. We have just moved our lines over to an Optus Multiline from a Telstra ISDN Onramp 30 service with 100 lines. My question for you good people is what sort of hardware do I need to interface Asterix into the Optus Multiline? The Optus service is terminated in my office to a SHDSL
2008 Mar 05
1
Newbie dialplan: dial 0 for outside line
I just managed to put in a TE410 card in an Asterisk box to work with OnRamp 20(E1 downunder). I am able to dial in but was not able to dial out. Can anyone offer me some advice please? In my extensions.conf, I just put in: [default] ... exten => 0,1,Dial(Zap/g1) and I get this on the console when I dialled 0. -- Executing [0 at default:1] Dial("SIP/5166-b76004f8",
2014 Feb 09
0
How to Busy signals on DAHDI [SOLVED]
2014-02-06 11:09 GMT+01:00 giovanni.v <iax at keybits.org>: > Il 05/02/2014 8.42, Olivier ha scritto: > > channel then it depends upon what you have the priindication option >> set to. With >> priindication=outofband then a busy cause code is sent to the >> network and the call >> is hung up. With priindication=inband then a busy tone
2009 Jul 03
0
DAHDI CDR problem
Hello gang, We just got MaBell to turn on our callerid. I tested the capability with a southwest bell box and a plain phone, so I know the line is sending the signal. I'm running Asterisk SVN-branch-1.4-r204834 using a TDM400P card. Here is my dahdi_cfg -vv output: dahdi_cfg -vv DAHDI Tools Version - 2.1.0.2 DAHDI Version: 2.1.0.3 Echo Canceller(s): MG2
2007 Jul 23
0
CAS signalling and FAX solution
I am trying to solve the fax problem by installing an E1 channelbank (Megaplex MP-104) It's a box that has 8 x FXS ports and a single E1 port. The plan was to use one of my 4 E1 ports to connect to the Telstra onramp and one to the MP104. I have since discovered however that the MP104 only supports CAS signalling and I am having trouble getting asterisk to work in this mode. Currently we
2004 Aug 13
2
te410p and Telstra Onramp 10
Hi, now that these cards have approval in Australia, has anyone had any luck in connecting them to a Telstra Onramp 10 service? Are these configured as a PRI, bchan=1-10, dchan=16 in zaptel.conf and switchtype=euroisdn in zapata.conf? Better yet anyone have any of the above .conf files they could share? Is an onramp 10 what is referred to as a 'channel bank'? Craig
2005 Mar 15
1
Unknown signalling 896?
I've been beating my head a bit against the 1.0.6 Debian builds of Asterisk, using an E100P (E1, single span) board. In machines I've built in the past (back in 1.0.0 days), config I'm using and that card and 1.0.0 driver combo worked fine. ztcfg reports no problems: SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1) 31 channels configured. And zttool sees the card, and
2006 May 22
0
Asterisk Nortel Legacy Integration
Hi Srs. we have to integrate a Nortel MATRA M6501-L with Asterisk with a TE410P. All call from outside get into asterisk and asterisk send to Nortel in a correct way. My problem is when a call is made from Nortel to Asterisk. If we digit a national Number in Spain([98]ZXXXXXXX or 6XXXXXXXX) all work find. But if we digit an international number call doesn't progress. I Have seen in
2005 Mar 28
0
Re: Asterisk-Users Digest, Vol 8, Issue 229
> On Sun, 27 Mar 2005, Nenad Radosavljevic wrote: >> Only way I have managed to get Zap channel to reject a call on TE110P >> without answering it, is to dial number that is not handled in dialplan >> (I >> have a ISDN PRI with 100 number DID service, and about 30 of them are >> handled by dialplan). So far I didn't manage to reject call that are >>
2011 Feb 18
1
Asterisk with TE 121 DADHI incoming calls fail
Dear Customer Support, i connected the asterisk to a e1 interface of our hipath4000. outgoing calls from a sip peer of my asterisk to an up0 telephone which iss connected to the hipath4000 are working. If you want to dial from an up0 device to the e1 interface where asterisk is connected to, you have to use the prefix 83. But when you enter the 3rd cipher this error appears at the cli
2005 Aug 23
1
Asterisk 1.0.9: TE411P replacement for TE410P 1stgen causes crashes
Hi all, I replaced a TE410P Rev C 1st Generation Firmware with a TE411P without any cfg changes (zaptel/zapata). As a result Asterisk crashes on outbound from PRI4 going to PRI1 calls: Aug 23 18:22:00 WARNING[4693]: chan_zap.c:7545 zt_pri_error: PRI: !! Got a UA, but i'm in state 1 Aug 23 18:22:00 WARNING[4693]: chan_zap.c:7545 zt_pri_error: PRI: !! Got a UA, but i'm in state 1
2005 Sep 27
4
BAD echo problems with Sangoma and Telstra
Hello, We have an Asterisk 1.0.9 machine with a Sangoma A101 card fitted, it is connected to a Telstra OnRamp E1 in Melbourne, Australia. The problem we are experiencing is extreme echo and clicking noises. These are only audible to the calling party, e.g. the person calling in from the PSTN to Asterisk via the E1, the person on the SIP handset cannot hear any echo or clicking, only the
2003 Jul 27
3
Australian Options
I would just like to get a refresh of the situation for Australian users. It would seem that the TE400P is currently available and is likely to acheive approval for use in Australia within the next 2 months ? (when is the end of summer?). Once this is done, it will certainly suit larger installations, but it still leaves a number of 'gaps'. Anyone with analog phone lines will need
2010 Sep 15
1
One way audio when overlapdial is set to yes
Hi Group, I am currently facing a dead end and any help will be much appreciated. I have an a104d installed in an asterisk box, two of which is configured on ISDN pri. One is facing pstn and the other one is facing a hipath 300e Siemens. I am getting one way audio when a local on the hipath tries to make a pstn call but no issue on incoming calls from pstn going to the hipath locals. local
2006 May 30
0
no extension from ISDN phone with bristuff
Hello, I have a Gigaset S44 connected to a quadBRI NT port. Receiving calls works phone, however when dialing out from the phone the call is dropped to the 's' extension, as if no extension had been dialed: -- Accepting voice call from '492389990' to 's' on channel 0/2, span 4 -- Executing Directory("Zap/11-1", "default") in new stack --
2008 Mar 11
1
WARNING[4294]: chan_zap.c:8851 zt_pri_error: 1 copying 5 bytes LLC
Hi I have recently upgraded my Asterisk system (from 1.2 to 1.4) and I have started to notice the following messages when I recieve a call on my Zap channel :- [Mar 11 09:20:17] WARNING[4294]: chan_zap.c:8851 zt_pri_error: 1 copying 5 bytes LLC I have a single PRI ISDN 30 link to a Siemens Realitis DX. Here is my zapata.conf :- [channels] echocancel=no echocancelwhenbridged=no rxgain=-5.0
2006 Mar 01
2
GXP-2000 Volume Issue
Is anyone else having an issue with GXP-2000s and transmit gain? All my other phones are fine on my TDM400P with txgain set at 0, but the GXP-2000 caps at about a third of the scale in ztmonitor. I'm getting people complaining they can't hear me on my GXP-2000s, whereas my Snom 320 and Polycom 301 are great, and my Budgetones are overmodulating. Is there any conceivable fix on the
2003 Dec 11
2
* CVS checkout does not work on one box
Hi, I have a strange problem trying to update Asterik on one of my boxes. I have done the following: - delete all the old source files - download the new file using: cvs checkout zaptel zapata libpri asterisk - compiling the new source file using: make clean ; make install Everything is compiled fine, except.... when I stop and start Asterisk server, it is still the old CVS version:
2005 Jun 20
1
Looking for PRI Outbound Caller ID Configuration
I'm having trouble setting the outbound caller ID on calls I make from my PRI trunk group. The PRIs are served out of a 5ESS. Telco has set the PRIs up for user provided caller id information, so I believe I just don't have it set up right in my dialplan or something. I can't seem to find an example of setting the outbound caller ID specifically for a 5ESS. Does anyone have an