similar to: S100U and TigerJet

When I try to start up zaptel, whilst running ztcfg, I get the following error: Jan 1 10:48:18 bu ztcfg: ZT_CHANCONFIG failed on channel 2: No such device or address (6) My /etc/zaptel.conf is: fxsks=1 fxoks=2 loadzone = au defaultzone=au Channel 1 is a X101P card connected to the PSTN and channel 2 is a S100U box driving an analogue phone. The zaptel kernel module gets loaded OK as does the

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I've tested the S100U unit in two different computers both with different USB subsystems. The one it worked the best in used the usb-uhci USB driver. The other system uses the usb-ohci USB driver. To make sure it was not the installation, I used the same hard drive that had asterisk in both systems. And I moved the X101P and S100U between both

Hi all, I am trying to add a TigerJet usb adapter to my asterisk installation I have the 1.2.4 asterisk bristuffed version, holding two zaphfc (ISDN) cards If I connect the TigerJet adapter to my linux box (Suse 10) i see: Bus 005 Device 001: ID 0000:0000 Bus 004 Device 003: ID 06e6:831c Tiger Jet Network, Inc. Bus 004 Device 001: ID 0000:0000 Bus 003 Device 001: ID 0000:0000 Bus 002 Device

Hi Everyone, I've been using Asterisk now for a few months for my small office (which is mostly just me while other guys are always on the road so we rely heavily on telephones) - I'm very excited with Asterisk as it can do everything I've ever wanted to do with a PBX. I'm having a problem with an S100U USB --> Telephone interface. I haven't actually made it work yet

Hi, I have been trying to figure out why the S100U is not performing very well on RH9.. Here is my thinking..( may be totally wide of the mark but here goes anyway) I remember reading somwhere that the sound system used by RH has changed... Does the S100U not depend on the sound subsystem?? So what I think is that the sound subsystem in RH9 and the S100U are not happy working together.. Does

Hi, I'm trying to get an S100U that came as part of the dev kit light working. I have tried compiled EHCI as modules or directly into the kernel but the same problem happens both times: I connect the S100U and run modprobe wcusb - initially nothing happens (great - no errors, etc). Fairly soon the server will die. It seem to be related to communications with the S100U. For example if I

Installing DevkitLite hardware (Very similar to John Lange's post on Tue Oct 08 2002) I cannot get anything to work on the phone connected to the s100u. I dont know what to do. Can someone please help me? I used the sample configuration files from digium documentaion that was supposed to be "sane" defaults for the kit. Very similar to John Lange's post on Tue Oct 08 2002 Here

Hi, I'm cutting my teeth setting up a home asterisk server, but having some trouble getting Zaptel to recognize a X100P clone PCI (Motorola SM56 which should work according to various wiki's). What struck me was that the "/proc/interrupts" do not include IRQ 11 as the "lpcpi -v" is reporting. Am I missing something fundamental here? Any hint is greatly

Hello people, Went to IRC and zoa helped a bit by saying me to Do a insmod zaptel and insmod wcusb When I did the insmod zaptel it worked fine, but when I did the wcusb it said asterisk:/usr/src/zaptel# insmod wcusb Using /lib/modules/2.4.24/misc/wcusb.o /lib/modules/2.4.24/misc/wcusb.o: unresolved symbol usb_submit_urb_R3d6f870e /lib/modules/2.4.24/misc/wcusb.o: unresolved

Hi All, I'm compiling zaptel. Did the usual ./configure, then make. Compile breaks saying: ---------------------------- /usr/src/zaptel-1.4.5.1/wcusb.c:1451: error: unknown field ?owner? specified in initializer /usr/src/zaptel-1.4.5.1/wcusb.c:1451: warning: initialization from incompatible pointer type make[3]: *** [/usr/src/zaptel-1.4.5.1/wcusb.o] Error 1 make[2]: ***

I have the dev kit lite installed, and after compiling and installing asterisk, I've become a little confused about how and when wcfxo and wcusb are loaded. When ever my box is done booting, the wcusb module is loaded, but the wcfxo module is not. Further, even though my startup notices say that asterisk started OK, it is not running by the time I log in and do a ps. First, where are the

>From - Received: from rwcrmhc12.comcast.net ([216.148.227.85]) by sccrmxc11.comcast.net (sccrmxc11) with ESMTP id <20031014185753s1100nos46e>; Tue, 14 Oct 2003 18:57:53 +0000 Received: from rwcrmhc12.comcast.net (localhost[127.0.0.1]) by comcast.net (rwcrmhc12) with ESMTP id <20031014185753014006qmtie>; Tue, 14 Oct 2003 18:57:53 +0000 From: Mail Delivery Subsystem

Any thoughts on the following? I am running asterisk from CVS (downloaded yesterday's version, just to be sure) on a test system with no digium cards in it, so I have installed ztdummy (see logs and screenshots below) as a timing source. When I call the music on hold extension from a Sipura Sip connected analog phone, I hear nothing and start getting Warning[98310]: chan_sip.c:674

I'm having a bad time getting 3 TE410P's and one TDM400 working in the same box. At some point during the install of second card, wcusb starts loading. I believe this is one of the TE410 Cards causing this as there is no usb enabled. Module Size Used by Not tainted audit 89880 2 (autoclean) usbserial 23420 0 (autoclean) (unused)

Hi, I am struggling to get rid of a conflict on DELL 2800 : PCI Parity error (EB113 on the display) I am learning linux and asterisk as I go along, there might be obvious things I should know, but bear with me. >From demsg below my 2 digium cards installed are listed (no config or connections done to digium cards yet), the conflict is with the TDM400P card, without that card, in any slot, no

Hi list, We have been trying to configure a Quad Span T1 card in a system running RH9. We have followed the instructions in the Wiki and searched the mailing lists, but so far havent got any success. Cable is connected to the first span, and module is loaded. Without loading the module the LED glows in red colour, but the moment we load module, it goes off. (No red or green) . We ran zttool

I try to use meetme app after reading manual i compile and install zaptel with ztdummy when i make lsmod i have ztdummy 2532 0 (unused) wcusb 20064 0 (unused) zaptel 179168 4 [ztdummy wcusb] usb-uhci 26348 0 [ztdummy] usbcore 51616 0 [wcusb usb-uhci] after it i recompile asterisk and after it i have

I'm trying to install on a 233Mz PII running RH7.1 kernel 2.4.2 The "astinstall" script pulled files from CVS ok and compiled with no warnings. When I try to run "modprobe wcfxo" and "modprobe wcusb" I get the following identical set of error messages: 15. Creating sample environment...SKIPPED ================= Installation Completed! ====================

i'm having problems with s100u (wcusb) on Via EPIA-V-8000 running RedHat Linux 9 (2.4.20-31.9). when i try to dial, asterisk won't respond (still hear dialtone) or get a fast busy. seldom asterisk would process the dialed number. i was able to dial to echo test and i noticed that the line is noisy (like chirping). anyone encounter this? i have no other s100u to check if this is a

Hi, I'm curious what chip Digium is using in the latest TDM400 cards. Specifically, to my recollection, they used to use the TigerJet 320G, however somewhat recently, Tigerjet was bought out, and now the 320G is no longer produced. Maybe a better question is: is there a way I can take the latest DAHDI source and get a list of supported chipsets from it? Thanks. MCH -------------- next part