similar to: Rough Two Days

Hello, I would like to know if voicetronix card (specially openswitch6 and 12) can be used with asterisk. Is there any driver for this card? Best regards, Daniel -- Daniel ANDRE (mailto:dandre@iris-tech.fr) IRIS Technologies - http://www.iris-tech.com Serveur kwartz - http://www.kwartz.com

Hello. Has anyone been able to successfully make data (dialup modem) calls through a TDM2400E? We're able to make fax and credit card calls fine, but cannot successfully make modem calls using a 56K modem connected to a patch panel connected to an FXS port which then gets bridged to an FXO port connected directly to a phone line. We have 'echocancelwhenbridged=no' set in

hello: thanks for Tzafrir Cohen for dahdi testing. I installed dahdi-2.1-r3c svn code and asterisk1-6 for testing OpenVox B400P and junghans card. i fund that there is bug (i think) to dectect NT or TE mode. actually on the board, i set it as TE mode, but after start wcb4xxp, but it show the port is NT mode. to detect the TE mode, I modefy the code in base.c

Seems strange to me that I should be having this problem but I'm stumped. I'm still playing with a Voicetronix OpenSwitch6 card and Asterisk (development CVS). I using a dialplan that's derived from one on another running installation that's using Digium FXS/FXO interfaces instead of the OpenSwitch card. It seems that as soon as a user on an FXS interface dials 7 digits, a call

Hi - I had a client recently move their asterisk system (asterisk 1.4.26, dahdi 2.2.0.1, aex800 w/vpm module) to a "new" location, a building that's nearly 150 years old. I was not personally able to go there, but the person who did the move said the building's demarc room was "scary"-- water leaks, jumbled and frayed wiring, and all sorts of other fun. The echo on

I just implemented a system using a TE411P hardware echo cancellation card. Per Digium, I setup zaptel.conf, and zapata.conf the same way as I always have. To my surprise calls out to the PSTN had a terrible echo. 1 - 2 second delay, and quite clear. The echo was so bad that I had to remove the hardware echo cancellation module from the card. We are only using the 1st span of this card right

Hi all, I have TDM2406E with 24FXO ports connecting to 10 POTS line sitting in my office. the out going calls symptom like when called party pickup the phone but the calling party still hearing the ring tone from the IP phone. Please light me up. it been many sleepless night by googling around trying to get the right answers. The digium card running on Intel 915G chipset. Below are my zaptel

I installed TDM400P and X100P pci cards in a system running mandrake 10.1 official, kernel 2.6.8.1-12mdksmp. I can compile zaptel, libpri, asterisk and modprobe (zaptel, wcfxs, wcfxo) without errors. Except that running ztcfg and asterisk fails. [root@asterisk asterisk]# ztcfg Notice: Configuration file is /etc/zaptel.conf line 3: Unable to open master device '/dev/zap/ctl'

Hi All, I have installed asterisk 1.6.2.8 Dahdi: 2.4.0 Digium card: Digium, Inc. Wildcard AEX800 8-port analog card I have configured this card properly and it is working for calls too, But there is issue of one way audio on this outbound routes only, My voice is going to outside pstn number but i am not able to get their audio, I have disabled firewall, selinux is also off. If I am applying

Hi, 1. Has someone met any success at all, connecting a Digium B410P to a Patton Smartnode 4638 (with latest 5.3 firmware) ? 2. If positive, then, which signalling was used on both sides ? My project's goal is use a Patton Smartnode 4638 to act as telco BRI lines, from a B410P-enabled asterisk box. In my testings, I can see channel is respectively up (with patton web server status page)

Does anyone know how to disable the VPM in software rather than removing the card altogether? The canceler isn't working as well as the software cancelers were. Aaron

Hi, I running into the following problem on my Asterisk setup: --snip-- [Sep 3 01:40:59] NOTICE[9170] chan_dahdi.c: PRI got event: HDLC Abort (6) on Primary D-channel of span 3 [Sep 3 01:47:07] ERROR[9170] chan_dahdi.c: No more room in scheduler [Sep 3 01:47:07] ERROR[9170] chan_dahdi.c: Asked to delete sched id -1??? [Sep 3 01:47:07] ERROR[9170] chan_dahdi.c: No more room in scheduler [Sep

Hello all - I'm trying to get Asterisk working with an Openswitch/6 card with all ports set to FXO for PSTN in/out, and 10 SIP phones on the LAN with the Asterisk server. The SIP phones are working properly to dial one another, but I can't seem to get a call to go out to the PSTN through the voicetronix, and I similarly can't get incoming calls to the lines hooked up to the

I'm working on putting together some Ideas about using Asterisk in our environment, one of the things I want to consider is DID trunks (analog), what hardware do I need to terminate these trunks? I'm looking at the voicetronix openswitch6 or openswitch12. On the openswitch, I'd like to use some of the lines for analog sets for the breakroom, kitchen, etc where they don't need all

Hi, I have a box with Debian Sarge, Asterisk 1.2.1 (and zaptel 1.2.1) and a TDM2400P with echo canceller. I installed the card but no echo cancellation is being made...seems like the echo canceller module does not work, infact the software cancellation is working. My zapata.conf has echocancel = 128 and echocancelwhenbridged = yes but no echotraining parameter which gives a warning. I found

Hi, I just read a pressrelease from VON that Digium will soon be releaseing a couple of new cards. What got me interested was: "The TE420P and TE415P support 128ms of G.168 (2002)-compliant echo cancellation across their entire 128 channels." Does anyone know when thease will be released and what they will cost when released? Thanks!

Ok, but is there a way to check if echo cancellation is active on a call in progress ? Thanks Giordano -----Messaggio originale----- Da: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] Per conto di Steve Davies Inviato: marted? 28 marzo 2006 16.43 A: Asterisk Users Mailing List - Non-Commercial Discussion Oggetto: Re: [Asterisk-Users] Echo cancellation

Hello all, I hope this is not off-topic, if it is please let me know. I'm currently playing with an Asterisk at home, in order to get to know it's ins and outs. Very very impressive indeed. I've got it hooked up to my home phone line via a Wildcard clone board (Intel modem with Ambient chipset), and it works like a charm. Zaptel picks up the card as a generic clone, and works with it

Hi all, In my Asterisk setup, incoming calls through Cisco PSTN gateway to Asterisk extensions sounds work fine. All calls can be terminated properly after hangup. However, when calls were forwarded to voicemail, after recording & hangup the PSTN calls and cisco FXO port remained connected unless cisco port was manually shut/no shut. # key used to hang up the call did NOT help. Did anyone

Hi all, I am having problems detecting fax on a client site using the TE406P (card with echo cancellation module) under 1.2 and was wondering if anybody was having or has had similar problems? Currently I can not get the system to detect fax for love nor money, in zapata.conf the relevant entries are set to: faxdetect=outgoing and I have a fax extension in the necessary context. I have taken