similar to: Waiting for your help...

Hi, I recently got a TDM04B and after installing and getting asterisk up and running I connected a handset to one of the ports. Unfortunately I don't get a dial tone when I lift the handset. What could be the cause of this? Could someone point me in the direction of a proper config for a TDM04B? Thanks.

Hello I am (attempting) to run the astlinux version of Asterisk on a VIA embedded platform. I have a TDM04B and pretty sure zaptel.conf and zapata.conf setup OK. They worked fine with same card in traditional PC anyway. I think need the module wcfxs for a Digium TDM04B card. Is this module not part of astlinux? Do I need to download it? Or is it in opt? I see wctdm - but think that is

I've installed a TDM400. Having a go with AMP. I would like incoming calls to be put throuhg to an extension (at my desk) and a mobile (cell phone) at the same time. Whichever picks up, gets the call.. This should be possible with AMP (call groups, 200|201|0*0408xxxxxx), but it didn't work, so I have created a custom-incoming in extensions-custom.conf What is happening is, The extension

Hi all, Has anyone had experience with installing AMP on a soekris box running Astlinux? Is it possible ? Cheers, Callum

I was searching thru the internet and I found a wide variety of different web interfaces for asterisks I was curious which one is best suited for asterisks. Thanks

Dear list, I was installing Asterisk via the AMP method off the AMP website. There is a portion in there where they want you to use perl-cpan to install telnet. The first time I installed I had no problem. I messed up and trashed the box further down in the install.. This time I made a mistake and put a -jp3 switch for multi processors. This has caused the install of telnet tank. I found

I have asterisk 1.0.5 installed via apt on a debian system. It's a custom distrobution called Voyage Linux that runs from a flash card and I have a hard drive installed with mysql installed on it as well as apache. I have been though the AMP install guide (asterisk management portal) and in the interface it has a place for me to record new IVR menus. I have to dial *77 to begin recording

I am having a problem with a couple servers. They both have a Digium TE110P and a TDM04B card. I have setup the system so the TE110P uses channels 1-31 and the TDM04B 32-35. The problem is that when we reboot the server sometimes the TDM04B is recognized first and the TE110P second so the configuration fails. I do not know why this happens and to solve this I have to do a "service

Skipped content of type multipart/alternative-------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: image/gif Size: 4732 bytes Desc: not available Url : http://lists.digium.com/pipermail/asterisk-users/attachments/20050717/6773439d/attachment.gif

Hi people, I would like to read your suggestions as to where the issue might be. ATA286=Grandstream Budgetone ATA 286 in SIP mode. One Lan Port and one FXS port. TDM04B= 4 FXO signal fxls There is a 8FXO-to-SIP unit in this scenario that works perfectly so i will not make mention of it. PSTN----VOIPprovider---Internet---ATA286------tdm04b---Asterisk1.2.-13 Asterisk is being used as a meetme

Hi, I am just trying to figure out how to setup a TDM04B card for incoming/outgoing calls. I have 4 lines, which are provided as a rotary trunk group, currently hooked into a Nortel system, which asterisk will replace. I have setup a Dell 1800 (Tower) system with the TDM04B card, which seems to work. The question is how do I set it up that all 4 lines are part of a trunk group, such that

Hi, Some weird problem (or I'm too sleepy) happens with a tdm04B revision G (4fxo) Steps: modprobe zaptel modprobe wctdm ztcfg -vv /etc/zaptel.conf fxsls=1-4 # TDM04B defaultzone=us loadzone=us /etc/asterisk/zapata.conf signalling=fxs_ls group=1 context=incoming channel => 1-4 modprobe zaptel and wctdm load fine, however ztcfg -vv shows: 0 channels configured Im using centos 4.4 with

Hello all, Asterisk Management Portal 1.10.009 has now been released. This exciting new version has several notable additions (listed below). The AMP homepage is http://amp.coalescentsystems.ca. Here you'll find links to the download, install guide, and documentation wiki. As usual, please use amportal-users mailing list for discussions about AMP:

Hi, I have the newbie guide from AMP's website and (fair enough) it is all about whitebox linux. Has anyone found any gotchas with the newbie guide relating to SUSE 9.2 ? Any help appreciated. Cheers -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050125/6b7a2f61/attachment.htm

I have a customer running Asterisk 1.2.13 with Zaptel 1.2.11 that is having calls dropped. Sometimes you can stay on the phone for a long time and sometimes the call is dropped within a minute. There are 9 lines connected to 3 TDM04B cards. The Panasonic Pbx we replaced did not have this problem. There are 8 SIP phones and 16 analog phones connected to two Astribank-8 units and everyone

Hi all, i've installed AMP and Asterisk following the INSTALL file and i have a problem with the TDM04B with 4 FXO: [root@srvoip ~]# ztcfg -vv Zaptel Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Slaves: 01) Channel 02: FXO Kewlstart (Default) (Slaves: 02) Channel 03: FXO Kewlstart (Default) (Slaves: 03) Channel 04: FXO Kewlstart (Default)

There was some discussion in the past about which one is the best Content Management System that can be used in conjunction with Asterisk. Mambo was supposed to be the best out there under GPL. The guys who developed Mambo have a new product now - Joomla. I am using this and it appears to be better than Mambo in many respects. Read the gist about Joomla below. ------------- If you've read

I had a working Asterisk 1.4.24.1 installation on SUSE 9 Linux but SIP only. I then downloaded and installed latest Zaptel and could not get Zaptel working. So I downloaded Asterisk again and re-installed. But still problems: Here is my ztcfg output: asterisk:/etc/asterisk # ztcfg -vvvvv Notice: Configuration file is /etc/zaptel.conf line 4: Unable to read Zaptel version information. Zaptel

Hello What is the difference between these 2 version of Asterisk in terms of functionality. For a small office am I going to run into problems if I use the easy version... Mike -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050717/311c56ec/attachment.htm

I am having a problem with and Asterisk installation where two ports connected to a TDM400 card will have a very loud noise when you try to dial. The server has an OpenVox D110P, a TDM04B and a Xorcom Astribank 8 fxs. It is running Zaptel 1.4.11 and Asterisk 1.4.18. The problem always happens with two ports (34 and 35) which are connected to two GSM gateways. They will work fine for a week