similar to: TE210P + MicroITX as E1 to TDMoE appliance?

I'm scoping out HA for a relatively simple Office/Call Center PBX. Current setup uses a TE412P with 4 PRI our telco with SIP hard/soft phones for users. Some outbound also goes to a SIP provider. Active/Active looks to be too much hassle for an installation this size, so we're looking at adding an extra * in an active/passive configuration with Linux-HA in between them. Does anyone

So here is my setup. Hardware: Intel P3 1.2 Ghz 1 GB RAM 36 GB Drives Mirrored Software: CentOS 5 2.6.18 Kernel Asterisk 1.4.14 Zaptel 1.4.7 (redfone) LIbpri 1.4.2 I'm using TDMoE with my PRI using a product called fonebridge from a company called redfone. They require that I use their own build of zaptel and I am trying to figure out if the problem is with them or something else. The

Hi, Some help with dimensioning the server will be gladly accepted. -50 sip phones (g729) or g711(to avoid transcoding) in LAN -an asterisk server (1.4) doing normal pbx functions + voicemail in the same LAN -Some sporadic conferencing with no more than 2 sip phones and maybe 2 or 3 calls coming from the E1 for a total of 5 people in a conference. The asterisk server will get an E1(pri) via one

I am looking for input on wether the 4 port T-1 foneBridge is a useful device in a asterisk deployment. Would it be better to loadup a extra asterisk server to trunk the T-1's via IAX or is TDMoE safe in production enviroments. We are only looking at 2 T-1's, one for pstn and the other to a channel bank. Any advice? Bruce Reeves Nortex Networks -------------- next part -------------- An

Hi all, I'm going to configure a middle asterisk installation. I'll use a TE210P to connect a T1 channel bank and a PRI E1 line. I'm thinking on using a SuperMicro P8SCT Mother Board that has a 1x 64-bit 133MHz PCI-X 3.3V. In TE210P documentation I've read: The TE210P is a 32-bit 33MHz card keyed for 3.3 volt operation. Can SuperMicro slot (that is a 133Mhz slot) be used

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I am stuck in a situation where I have two te110p's and really need a te210P. Anyone interested in a trade? They are in working condition guaranteed. If this is the wrong forum for this, I am sorry... I will take it off list. -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.2 (MingW32) Comment: Using GnuPG with Thunderbird -

Hi list! I'm trying to setup a new * server with a TE210P in a Dell 2850 box. I'm using zaptel version 1.2.5, the linux flavour I'm using is CentOS 4. In a previous thread I read about the results I should expect from zttest. On my home box (using the crappy Asus A7V600) I got really bad results from zttest (just over 97.5) but I know that this motherboard just sucks. To my

Has anyone on the list used a Soekris engineering PC as a TDM - Ethernet bridge? For example something like a net4801 with a TE110p in it and then using TDMoE to get it into a bigger server where the call processing proper will occur. Anyone know if it might handle a quadspan card ok? (no transcoding, just pure PRI to TDMoE bridging). Craig

Dear all I have now install TE210P 2 port E1 card on asterisk 1.4.10 on centOS 5 but thing is that i have connect 1 E1 port with avaya E1 back 2 back and second E1 card on Direct Telcom for outgoing for outside now i got this error when i call on avaya PRI asterisk think PRI_CPE and remote end also CPE i have configure /etc/zaptel.conf span=1,1,0,ccs,hdb3

Hello, I'm just starting out with asterisk and I'm playing around with the system. Currently I have a Digium TE210P connected to a PRI on the Asterisk server. I have a SIP soft phone on my laptop for testing that is working fine. When I try to place a call from my soft phone I get this from Asterisk: May 1 09:11:41 NOTICE[20098]: app_dial.c:1029 dial_exec_full: Unable to create

Hi all, Our asterisk PBX, randomly restarts all the channels of the E1 connection. It sends this message "There is no D-Channel, using channel 16 anyway".Then the asteisk recive (or it thinks it recives) yellow alarms at all the B-channels, after that it restart all the channels. When restarting the B-channels it cut all the conversations that is handling at that moment. Does anyone

When I was trying to run mutiple E1s over TDMoE, the zaptel would drivers complain about too little memory, whenever I added more than 31 channels. Requesting 62 channels in a dynamic span gave me ... span creation failed: Cannot allocate memory upon loading the zaptel drivers. How would you go about running, 8 or 16 say, E1s over TDMoE? Would you create multiple dynamic spans or just one large

Hello, I have been struggling with the configuration of this card on my box. I have a T1 line and I am trying to setup asterisk with it. I followed all the instructions and I still see a blinking red light on the card. I use fedora 12. If everything is fine should I see a green line when I plug in the T1 line ? I want to isolate the issue so I di not start asterisk. When I run asterisk I get

I have a T400P in my main building M and am going to put asterisk boxes in two buildings A & B. I already have our wan on fiber running between the buildings (including some extra strands) and the distance is beyond straight Ti distance so I would need csu... to use copper. It occurred to me that I could use TDMoE - and it may be less costly. My assumption is that the best to avoid the

We have been pretty much able to solve our echo problems, except for the primary mode in which we desire to operate our system. See system diagram at bottom. Prior to making adjustments to cancel echos (all echocancel=no): Call Type Result (Before) --------- --------------- CP <- LEC PRI * TDMoE * FXO -> AP

Hi all, My asterisk (1.2.4, zaptel 1.2.2) running in Dell PowerEdge 830 box is having problems with Digium TE210P card that I use for PRI connection. My problem is stability. Sometimes the box just boots OK with a full functionality, no problems at all, sometimes (after power outage) it halts during boot with the amber control LED flashing. Sometimes (most frequent scenario) it just boots OK and

Hi list! Has anyone ever tried the following installation : I want to replace our legacy PBX with Asterisk but... I still need the legacy PBX as a 'channel bank' for fax (I need E1 not T1) I will put a dual port PRI card in the Asterisk box, and for incoming and outgoing faxes I want to use native bridging on the TE210P and route fax calls (based on DID and prefix when dialling) to /

Hello, I recently acquired a Digium TE210P for a faxing solution I'm working on. I would like to use the card to send faxes from my infrastructure using Asterisk and HylaFAX. I'm curious if the zaptel driver will recognize in/out faxes to/from the TE210P. Is this going to work or should I not even try? Thank you in advance, I greatly appreciate it. -Dan -------------- next part

Hello, I've been using TDMoE accross 2 * boxes for months. It was working well, but * would crash when anyone would try to connect via h.323. So, I got the latest CVS release and compiled without h.323 support. After I made and installed the latest CVS the TDMoE channels stopped working. They have been working great (especially after we got echo cancel working them, thanks Mark) and the

Hello, I want to link several * boxes together. Some of them are dedicated as "user" servers (SIP and IAX clients connect to them) and some are used as PRI servers (where the PRIs are hooked onto). I think TDMoE is the only channel type where you can group different Interfaces into a single group. E.g. for using Dial(ZAP/g1/12345), I think you cannot group different IAX accounts