similar to: ISDN Eicon Diva Server V-BRI

We are experiencing slightly distorted audio with playing of recordings on our Asterisk server when the call comes in over our Eicon Diva Server BRI card. An example is an incoming call to IVR and playing some of the standard Asterisk voice prompts. Note that there is no audio problem with internal access to the same recording. Neither is there a problem with calls not involving the playing of

Hi list, Does chan_capi work with kernel 2.6? The Eicon Diva server card loads fine judging from /var/log/messages but Asterisk gives an error when trying to load the chan_capi module. I'm using chan_capi-0.3.5, zaptel-1.0.0, libpri-1.0.0 and asterisk-1.0.0 on a Fedora box with kernel 2.6.8-1.584. Zaptel and ilbpri work fine as does *. I have seen a msg that may be related and don't know

I am trying to use chan_capi with an Eicon Diva Server BRI. I installed the Eicon drivers from source including CAPU and I can use the board correcly using tty_test and minicom over /dev/ttyds01 or /dev/ttyds01. I need to insmod capi ( why? it is not written anywhere) and then capiinfo shows me all board parameters, but I have to break it otherwise capiinfo doesn't exit at all, but I don't

Hi; I've got an AAH installation where a customer wants to install an active Eicon DIVA BRI card. AAH is built on Centos 3.5 which is currently at kernel 2.4.21.37. Support for Eicon active cards is built-in. I've debugged and run the A@H install-Eicondiva script but when I try to run divactrl load -c 1 -f ETSI -Debug I get a response : A: can't get card type for DIVA adapter

Hi Everybody, Has anybody tried the above (or indeed any other 4XBRI cards) successfully with Asterisk. As far as I can see the above mentioned card is an active ISDN card but supported by it's own I4L driver. This leads to interesting questions particularly regarding echo cancellations (which usually doesn't work on the cheap passive cards with one exception as far as I can see).

Hello, I have an issue getting the chan_capi module to load in asterisk cvs from today. Plain 2.4.20 kernel with melware patches for the Eicon Diva Server Bri card. I load the modules with: modprobe -v divas divacapi I load the firmware with: divactrl load -c 1 -f ETSI -vd6 Output in /var/log/messages is: Nov 9 19:26:26 voice kernel: Eicon DIVA - DIDD table (http://www.melware.net) Nov 9

Hi (Armin?) ! Today I had a problem with Diva Server 4BRI-8M 2.0. Asterisk 1.2.12.1 chan_capi-cm-0.6.5 divas4linux-melware-3.0.f-106.622-1 Asterisk could not receive and make calls on the BRI ports, although the ports looked fine within Asterisk. I usually use "/usr/lib/divas/divactrl dchannel -c 1" to test line activity. This time there was no activity (cryptic log

Hi *, I want to integrate the Eicon Diva 4Bri Card to Asterisk. Eicon drivers and capi is installed. I use the latest dev version from eicon compiled and installed for my fedora 2 system. I found the chan_capi for asterisk from www.junghanns.net. Also loaded the patch and applied to the chan_capi source tree. I changed the Makefile to include the capi20.h from eicon:

Hello Everyone, I am once again wondering about EICON. I have had no success with the Diva Pro or Diva Pro PCI, so my question is, does anyone use an Eicon Server BRI card on Asterisk? Or would I be better off trying to get a split PRI? Regards, Greg

Hi, I would like to set up a high density FAX/PBX server, am looking at using Eicon Diva E1 card with Asterisk and Hylafax sharing channels, is this possible. I know Extensions can be reserved for voice OR fax with the combination of chan_capi used for * voice, capi4hylafax on fax but then channels must be dedicated rather than shared ie. would like to be able to answer voice/fax on same DID.

Hi! I'm trying to enable echo cancelation with my Eicon Diva Server 4 Bri card. I've enabled it from zapata.conf, (as I read from www.voip-info.org) ------------------------------- ; Enable echo cancellation echocancel=64 echocancelwhenbridged=yes echotraining=2000 ---------------------------- but nothing seems to change, echo is still present. Any idea? Should I enable/change something

Hello all, This afternoon I had a BRI line installed by Telstra (our telco in Australia). I'm using an Eicon Diva 2.02 PCI ISDN card with the isdn4linux driver. Incoming and outgoing calls with Asterisk work fine (and with no echo - my main reason for getting ISDN). However, I can't seem to get outgoing DTMF working (incoming works fine). I made a call from my desk phone (Cisco 7940G)

Are there any step by step instrunctions on how to install drivers and I guess bristuff for this card? Just need to use it to handle voice on 2 BRI circuits (UK) then utilise with Asterisk and some Digium cards handling POTS phones (and some VoIP out the back). It's the EICON card stuff and how to make it all work I'm finding confusing? Steve -- NetTek Ltd UK mob +44-(0)7775 755503

Hi! I have some (short) question about the Eicon DIVA (V-)4BRI cards I want to have (short) answered before buying the DIVA card. I know there are several Eicon guys active on the list, thus I ask on the list instead of directly to Eicon so that all other will benefit as well. 1. Do Eicon DIVA (V-)4BRI cards support TE and NT mode? 2. Can the clock (master/slave) be configured independent

Hello all, I'm having problems getting chan_capi 0.3.5 to work well with an Eicon Diva Server card using using the driver from linux kernel both 2.6.10 and 2.6.12 (vanilla versions). I have a (really two) producci?n system(s) running chan_capi in another identical Eicon Card using kernel 2.4.27 and the Diva Server drivers from Eicon. I installed an compiled the source level rpm

Hi I've got a dell 2550 with an Eicon Diva server PRI card plugged into it. I can call out using the acopy2 test utility. I'm having trouble with asterisk making calls however... my capi.conf and modules.conf looks correct by the wiki instructions - does anyone have any advice on where to look ? I can attach conf files etc. if needed. Asterisk says it has 30 capi channels available,

Hello Marc, Could you post the install details for the Diva PCI? I have a Diva Pro PCI 3.0 and I am looking to get it working... I am running Debian Testing. So far it appears there are a few things floating around but I am not certain which direction to go. I know I need to load the firmware first. I did manage to load the modules ok. Thanks, Greg -----Original Message----- From:

Hello, I try to use Asterisk with an Eicon-card called "DIVA Server 4BRI-8M PCI" but I don?t get it to work. I?m running on RH8.0. The Eicon-card supports isdn4linux. In the modem.conf file i have put following: ----------- [interfaces] ; By default, incoming calls should come in on the "remote" context context=remote ; Modem Drivers to load driver=i4l ; Type of dialing

Hello everyone! I've got a Eicon Diva Server BRI card into my "*" box working just fine, but I wander if there's anything I can do to improve voice quality for my operators. I'm thinking something along the lines of "auto gain" and sudden noise suppression (like when you hit a fax machine or the other party accidently touches the dial pad on the phone). Does

I have read most of Eicons information on Q.SIG, and I am able to load the Q.SIG protocol (instead of ETSI for example). No strange logging in divacrtl mlog. But how do I tell Asterisk to understand Q.SIG? My PBX is configured for QSIG, but I cannot see anything on my trace when trying to make a call via the S0(Q.SIG) Janne > -----Ursprungligt meddelande----- > Fr?n: