similar to: Re: Asterisk-Users Digest, Vol 18, Issue 134

Has anyone a working /etc/asterisk/capi.conf example for Germany or Switzerland using the AVM C4 - ISDN Card. I try to connect asterisk to 3 wires BRI-ISDN (Swisscom). I appreciate your help and it would save me a lot of time, figuring it out by myself. regards, Claudio

Hallo all, I am trying to get * with chan_capi and a ptp-ISDN with 4 lines on a AVM C4 card to work. But weather inbound nor outbound is working :( My capi.conf: ; ; CAPI config ; ; [general] nationalprefix=0 internationalprefix=00 rxgain=0.8 txgain=0.8 [interfaces] mode=immediate isdnmode=ptp msn=8993 incomingmsn=* mode=immediate controller=1,2,3,4 softdtmf=1 ;accountcode= context=demo

Hi, I have done my best and tired of searching the net about the problem. If anybody could help would be a great favour. Description of Problem ------------------------ I am trying to install two Netpci cards(Traverse Technology Netjet ISDN-s) on Trixbox 2 and aim is to use in Asterisk as dailin and dialout. I compliled the driver as directed in the manufacture manual. After installation dmesg

I'm getting a strange error on one of the two controllers on an AVM C2 card under chan_capi-cm-0.6.3. I have two ISDN controllers defined, both in the same group, both connections are UK ISDN2e Point to Point: On the third outbound call (both of the first two calls are handled by the second controller "ISDN2",) I get this error : chan_capi.c conf_error 0x2001 PLCI=0x301

Hello everyone, I have been using an AVM Fritz! card with chan_capi and mISDN for quite a while in PTM mode and it was working finely. Now, I needed more DID/MSN, so I switched to PTP. But now nothing works anymore :( I am using Asterisk on Debian Sarge stable and installed Asterisk along with chan_capi from apt-get. I installed mISDN from the CVS of isdn4linux.de. It is : - Asterisk

Hi, I am requesting for a E1 connection from my telco. They are asking if I want DSS1 or SS7, and I am stuck here. Could someone tell me the difference between the two? How should I decide which one to use? Thanks in advance for your help. Mark -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello, I just received a couple SX440isdn phones and was wondering if they can be plugged into a Diva 4BRI port in NT mode and work with asterisk+chan_capi? I know they probably work fine with mutliHFC cards with either bristuff of chan_misdn but since I have some spare Divas, I was curious about their potential as phone ports. The Diva's 3 and 4 ports are already set to NT mode at boot

Hello Group, Current Setup: - Eicon Quad BRI ISDN Card. - 4 ISDN BRI (Telco: Telstra) Onramp2 services. - Mode: Point2Point. - 100 Indial Number ranges. Full National Number (9 digit format): BAAAAAAXX where: B (Area code): 2/3/7/8 A (Normal Numbers) X (99 Indial extensions) eg: BAAAAAA00 BAAAAAA20 etc Requirement: - To be able send Indial numbers as Caller ID when dialing out. Configration:

Skipped content of type multipart/alternative-------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: image/bmp Size: 2918 bytes Desc: Picture (Metafile) Url : http://lists.digium.com/pipermail/asterisk-users/attachments/20050307/cb404791/attachment.bmp

hi all, i have a probably very stupid question/problem. for testing purpose i am trying to get asterisk running with two isdn cards. I'd only like to here the demo sound when i call the number - but nothing works. The output of show channels is not showing any channel - should there be 4 channels ? - capi info shows my two cards perfectly. The ISDN Controller's are attached to an PTMP

I've having a big problem after having upgraded to 1.2.4 and chan_capi-cm 0.6.4 When making outgoing calls I don't seem to have any control over the CLI that is presented to the called party -- it can be any one of the MSNs allocated to the line, allocated on what seems to be a random basis. This is on a BT Business Highway line (which is essentially an ISDN2e line with two built-in

Hi, 1. Has someone met any success at all, connecting a Digium B410P to a Patton Smartnode 4638 (with latest 5.3 firmware) ? 2. If positive, then, which signalling was used on both sides ? My project's goal is use a Patton Smartnode 4638 to act as telco BRI lines, from a B410P-enabled asterisk box. In my testings, I can see channel is respectively up (with patton web server status page)

Hi list, I am searching for a possibility to do a certain call transfer method which is called "path replacement" in QSIG. But I want to do that in DSS1 (EuroISDN). If my asterisk does a call transfer I want the machine to signalize on dchan that the call path has to be replaced to a direct connect between the caller and the called, i.e. my machine is to hang up after the transfer and

Hi, I'm trying to get Asterisk working with the AVM B1 card. I've tried every instruction set I can find, but to no avail. I think I'm getting mixed up as to what Zaptel/CAPI configuration to use. If someone is currently using one of these cards, would it be possible to mail me a few bits of the important config files? Sorry if I should have included something else too, but let me

Hello, I need to connect one diva server 4bri to a portuguese BRI interface. The operator (PT) said that this bri is in point-to-multipoint mode (S0). Previously one PBX has connected to that interface. The asterisk and diva drivers are working ok but i cannot communicate to outside via this bri. Xlite gives me the message: "call failed: declined". Anyone have experience with this

Hi; I've been asked to take a (remote) look at an Asterisk@home system running asterisk 1.0.9 on Centos 3.5. It's running chan_capi-0.3.5 It has an AVM c2 ISDN card which is plugged into what I believe to be a couple of BT ISDN2e "System Access" (i.e. point to point) connections. We've placed a support call to BT to find out how these lines are actually provisioned, but

Do you have any extension in default context of your extensions.conf file to accept incoming calls ? It must be something like; exten => 12345678,1,Answer() exten => 12345678,2,Playback(Welcome) ... 12345678 = The DID number you are calling to reach E1 Idris -----Original Message----- From: Erick Perez [mailto:eaperezh at gmail.com] Sent: Thursday, July 26, 2007 7:03 AM To:

Hi all ! We have 3 NTBAs which are all going to our existing PBX. Our areacode is 06003 and our DDI enabled number 9141. I want to exchange that PBX with Asterisk, but still struggle to get it working. My CAPI.CONF is currently like this: [general] nationalprefix=0 internationalprefix=00 rxgain=0.800000 txgain=0.800000 [interfaces] context=in-capi msn=60039141 incomingmsn=* controller=1

Hi, i will use an AVM C2 controller with asterisk. How can i use both card ports ?? On the voip-info.org Wiki is only notice to: You will need a section for each controller in /etc/asterisk/capi.conf so the C2 will have 2 sections. But how is look like this ? Only on the first port is asterisk assume connections, but nothing on the second card port. In the dmesg is only the capidrv-1 shown,

I have installed an Asterisk 1.4 on Suse93 using a FritzCard. Some calls are logged to the ISDN log, but Asterisk is not detecting incoming calls. I wonder whether some other device or process is preventing Asterisk from gaining access to the isdn line? Is there some way to ensure that only Asterisk can listening to the line, or get it to share the line with some other device, such as the fax