Displaying 20 results from an estimated 3000 matches similar to: "PRI D-channel errors"
2010 May 31
1
Suddenly "HDLC Bad FCS (8)" errors on ISDN-PRI, changed nothing
Hi fellow asterisk users,
I am running Asterisk 1.4.29 with an Digium TE121 card (wcte12xp kernel
module) an approx. 100 snom320. The whole installation is running
without issues since 5 months.
Without having changed anything on the asterisk server for at least 2
months, i noticed "clicking sounds" at external calls over the PRI.
Asterisk constantly throws the following messages:
...
2006 Dec 28
1
TE110P with Qsig
Hi all, as good?
I am trying to go up a board TE110P with link E1 ISDN PRI to establish
connection with a central office Siemens HiPath 4000. But I am having the
following errors:
Server1:~ # asterisk -r
Asterisk 1.2.10, Copyright (C) 1999 - 2006 Digium, Inc. and others.
Created by Mark Spencer <markster@digium.com>
Asterisk comes with ABSOLUTELY NO WARRANTY; type 'show warranty'
2007 Jan 25
2
TE110P and HDLC problems
Hi!,
this issue makes me crazy. I read a lot of docs, also * mailling list
and I try a lot of things without success.
Any help will be appreciated. Here is the info:
Hardware:
--------------------------------------------
Supermicro Server with motherboard X7DB8, chipset Intel 5000P, Xeon 5050
Digium TE110P
Software
---------------------------------------------
Asterisk version 1.2.12.1
2005 Jun 29
4
PRI got event: HDLC Abort (6) on Primary D-channel of span 1
I receive this error on the asterisk console and it is pretty much
ALWAYS coming up.
Sometimes there will be a break where it does not display.
We had our PRI provider test the lines and they claim that there is no
signalling problem.
It doesn't matter if there are no calls or if there are 10 calls in
progress the error is still displayed.
I also get an annoying popping or clicking sound
2006 May 31
1
Connect 2 Asterisk Servers via PRI
I am trying to test out my PRI configuration on a server by conection
another asterisk server to it. I have the T-1 cards up and both set to
bchan=1-23 and dchan=24 in zaptel.conf I am getting lost on the signalling
in zapata.conf. using pri_cpe makes sense for my target box, but I am
getting the following errors on my source box if I use pri_net or pri_cpe
signalling.
May 31 17:15:06
2011 Jun 01
10
busy hangup HDLC Bad FCS (8) on Primary D-channel
Hi all,
After running fine for a few months now asterisk seems to hang
frequently , still functioning but the DAHDI channels seem busy (users
report a busy signal when calling or being called)
A reboot will allow it to run for another day or maybe 2 or 3 till the
problem occurs again.
running stock Asterisk 1.6.2.9-2+squeeze2 on Debian with stock kernel
2.6.32-5-686
i get the following
2010 Jul 19
1
Problem with E1
Hi All,
I am facing problem with E1 line. I have installed Asterisk
(1.4.20.1) on a system with Digium TE420 card (Zaptel- 1.4.10)
But every
now and then I face problem of down E1's. The log show lot of entries like
"pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of
span 2"
This happens on a regular basis and the E1 becomes up after some
time.
My
2010 Dec 16
1
PTMP BRI Unable to receive TEI from network in state 2(Assign awaiting TEI) - Asterisk 1.6.2, Latest DAHDI, LibPRI
Hi all,
Last night I went to replace an Asterisk 1.4 + mISDN + b410p box with
Asterisk 1.6.2 and DAHDI BRI - to no avail.
I had two servers so copied network setting etc from the working one,
moved the card across, ran dahdi_genconf etc and it didn't work.
Here's the console output with notices disabled:
lucas*CLI> pri intense debug span 1
Enabled debugging on span 1
[Dec 16
2006 Apr 27
5
PRI configuration
Hi,
I am getting this message on the * console on my first pri span. Pri
show span show it is down, and I can't make any calls from the span.
Apr 27 07:40:23 NOTICE[23988]: chan_zap.c:8202 pri_dchannel: PRI got
event: HDLC Abort (6) on Primary D-channel of span 1
Apr 27 07:40:23 NOTICE[23988]: chan_zap.c:8202 pri_dchannel: PRI got
event: HDLC Abort (6) on Primary D-channel of span 1
Apr 27
2007 Sep 20
9
Problems Connecting Two Asterisk Installs Via ISDN PRI Cards
I am trying to connect two machines to each other with an T1 crossover
cable. The first machine has two TE120P cards - one connecting to the telco
on an ISDN PRI. The second to a crossover T1 cable to a second machine which
has one TE120P card.
Telco <-cA-> Machine1 <-cB-> Machine2
Machine1: Two TE120P cards
Machine2: One TE120P card
cA: Standard T1 Cable
cB: Crossover T1
2007 Sep 13
2
Fwd: Bad FCS error
---------- Forwarded message ----------
From: Jan Prunk <janprunk at gmail.com>
Date: Sep 13, 2007 3:35 PM
Subject: Bad FCS error
To: asterisk-users at lists.digium.com
Hello !
I am getting the following error in asterisk logs:
Sep 11 17:33:30 NOTICE[2187] chan_zap.c: PRI got event: HDLC Bad FCS (8) on
Primary D-channel of span 1
Sep 11 21:45:08 NOTICE[2187] chan_zap.c: PRI got event:
2014 Oct 14
1
debugging T.38 issues
Hello list,
We're currently facing some issues concerning T.38 gateway faxing.
This is a device used almost exclusively for receiving faxes. Calls
are incoming to asterisk on a SIP trunk (sangoma netborder) using
G711A. Gateway mode is activated in the asterisk dialplan towards a
Cisco SPA 112 running firmware 1.3.5. We are using asterisk 1.8.13.0
with the T.38 gateway patch applied (I know I
2006 Apr 24
1
E1 testing
Skipped content of type multipart/alternative-------------- next part --------------
Console logs from Asterisk A:
Executing Dial("SIP/test0-5821", "Zap/6/327557670||Tt") in new stack
-- Requested transfer capability: 0x00 - SPEECH
-- Called 6/327557670
-- Zap/6-1 is proceeding passing it to SIP/test0-5821
-- Accepting UNAUTHENTICATED call from 195.66.73.122:
2005 Jun 23
1
HDLC abort 6 error
I've read as much as I can on this error and still can't seem to figure
out what's causing this error:
Jun 23 20:54:58 NOTICE[7483]: chan_zap.c:7395 pri_dchannel: PRI got event:
HDLC Abort (6) on Primary D-channel of span 1
Jun 23 20:55:03 NOTICE[7483]: chan_zap.c:7395 pri_dchannel: PRI got event:
HDLC Abort (6) on Primary D-channel of span 1
Jun 23 20:55:03 NOTICE[7483]:
2005 Oct 04
2
Quad PRI Problems
I have been getting quite a bit of PRI Resets using my Quad PRI Digium
card.
Prior to the resets I am getting similar notices to the following
chan_zap.c:7482 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary
D-channel of span 3
Telco claims the PRI's are fine on their end and that it is my unit.
Is this timing? (google somewhat leads to this) I am running 1.08
asterisk zaptel
2005 Feb 17
2
Sangoma A104 - D-Channel problem
Hello,
I have following problem with Sangoma A104 card:
CLI> pri show span 1
Primary D-channel: 16
Status: Provisioned, Down, Active
Switchtype: EuroISDN
Type: CPE
Window Length: 0/7
Sentrej: 0
SolicitFbit: 0
Retrans: 0
Busy: 0
Overlap Dial: 0
T200 Timer: 1000
T203 Timer: 10000
T305 Timer: 30000
T308 Timer: 4000
T313 Timer: 4000
N200 Counter: 3
NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI
2005 Jul 04
1
HDLC bad FCS
I have 2 servers, configured identically. Each has a TE405P and 2 PRIs. One server was experiencing crackly audio on one circuit, accompanied by HDLC
bad FCS messages. The telco recabled and moved me to another port on the DMS-100. The audio is better, but there are still bad FCS problems on the
span. I have moved the PRI in question to the other server, and the problem does indeed move with the
2006 Mar 31
2
PRI issues
Hi everyone,
I have been having some problems lately with our PRI and Asterisk, or
maybe it is just me. It happens once maybe twice a day, but when some of
our customers are calling in, the phone just drops on them. I pulled the
information below from the log from one that happened. I notice why it
is happening, but I can't seem to figure out a way to stop it from
happening. I also
2010 Jun 11
1
HDLC Bad FCS (8) on Primary D-channel
Hello,
I've got a running system in which logs are full of messages such as:
[Jun 10 07:24:14] NOTICE[2414] chan_dahdi.c: PRI got event: HDLC Bad FCS (8)
on Primary D-channel of span 2
The strange thing is those messages are coming from a single span.
My setup is :
Asterisk 1.6.1.18
Junghanns OctoBRI
with wcb4xxp driver
libpri 1.4.10.2
dahdi 2.3.0
3 BRI lines in PtMP mode
What does this
2011 Jan 24
1
B410P: DAHDI BRI PTMP HDLC Abort (6) on Primary D-channel of span 1 (TEI Errors)
Hi all,
So, we reverted the LibPRI version and tested it, and then tried with
the latest version of everything. Still no changes.
The BRI line is in PTMP. If we set the configs to PTMP in the
genconf_parameters and try it, we get the following:
[Jan 21 17:32:20] ERROR[20341]: chan_dahdi.c:12645 dahdi_pri_error:
Unable to receive TEI from network!
If we set it to PTP (which it is not) we