similar to: chan_capi-cm and DID

Displaying 20 results from an estimated 800 matches similar to: "chan_capi-cm and DID"

2005 Sep 02
2
chan_capi hfcpci mISDN linux 2.6.12 not working
Hello, These are error messages I get when I try to call a number over CAPI channel. -- Executing SetCallerID("SIP/xlite1-3b80", "0") in new stack -- Executing Dial("SIP/xlite1-3b80", "CAPI/hfcpci/b17") in new stack > data = hfcpci/b17 > capi request for interface 'hfcpci' == hfcpci: Call CAPI/hfcpci/b17-1 (pres=0x00,
2006 Jan 13
2
PrimuX Cards with chan_capi-cm
Hello List, I'm trying to get a PrimuX Card (www.primuxisdn.de) working. The Manufacturer says that chan_capi (the older one) used to work. Now I'm trying with chan_capi-cm and have got the following problems: Outgoing calls "ausgehend_ueber_ntba_primux.txt" the other phone rings but when I answer the call asterisk crashes. Incoming: first tried with immediate=no
2006 Jun 04
5
chan_capi-cm-0.6 and incoming calls problem
I have a problem receving calls via the ISDN line, using the followin components Asterisk 1.0.9 with asterisk@home chan_capi-cm-0.6 AVM Fritz card datalink protocol = point to multimode I can make calls out with no problems so the issue is only incoming calls. When I make the call from an external line to the ISDN line connected to asterisk, I get a busy signal after about 5 seconds. I have
2004 Jun 07
6
chan_capi and DDI (Anlagenanschluss)
Hi all ! We have 3 NTBAs which are all going to our existing PBX. Our areacode is 06003 and our DDI enabled number 9141. I want to exchange that PBX with Asterisk, but still struggle to get it working. My CAPI.CONF is currently like this: [general] nationalprefix=0 internationalprefix=00 rxgain=0.800000 txgain=0.800000 [interfaces] context=in-capi msn=60039141 incomingmsn=* controller=1
2005 Dec 30
3
using a Gigaset SX440isdn on a Diva 4BRI ?
Hello, I just received a couple SX440isdn phones and was wondering if they can be plugged into a Diva 4BRI port in NT mode and work with asterisk+chan_capi? I know they probably work fine with mutliHFC cards with either bristuff of chan_misdn but since I have some spare Divas, I was curious about their potential as phone ports. The Diva's 3 and 4 ports are already set to NT mode at boot
2004 Jun 28
4
Chan_Capi Down
Hi all, * was running ... I have a WT405P and an AVM C4 with chan_capi 0.3.4a Today chan_capi stopped working, without any changings at the system. It seems, that not * is the reason, because isdn-log also shows no calls. If I try to call * from outside via capi, I only get a busy. That is the try from inside to outside: stern01*CLI> -- data = @89930:0107901723168212 -- capi
2005 Sep 19
0
Call dropped 100% of time when incoming IAX routed to outgoing CAPI
Good day, The unusual thing about this problem is that it doesn't occur just during a CAPI call, or just during an IAX/SIP call. Only during IAX/CAPI I'm having some trouble with the CAPI interface and it only occurs when a call comes in on an IAX channel and goes out the CAPI interface. The capi debug in the asterisk console is below as well as the relevent parts of .conf files from
2007 Sep 13
1
fax machine detection for outgoing call on DIVA card
Hello, I need to detect both fax and answer machine, and it should be valuable that the detection will be run by the Diva card itself. So : - I read Diva Documentation, and I found that the Diva could send some specific DTMF, if I had "[..] enabled [this functionnality] by the application for a designated controller through a manufacturer request command 9 [...]", but I didn't
2010 Mar 09
0
Asterisk 1.6.2.5 crash with chan_capi upon calling to PSTN
Hi, I am having a problem with (Asterisk is crashing) with a Fritz card PCI / chan_capi. Receiving Calls from PSTN works, but outbound calls make asterisk crash (Speicherzugriffsfehler/Segmentation fault). The crash occurs upon dialing with the other phone not even ringing. I hereby ask if somebody reading this list can confirm or disprove my issue. Does anbody run a recent asterisk 2.6 with
2004 Nov 27
2
capi question
hi, I've been running a pure sip asterisk box for a while now with no problems, and i've recently added an isdn2e line from bt in the uk. everything is hooked up and i've got it ringing my sip extensions, but the logs don't quite look perfect and i can't see any description of what i should consider to be normal behaviour. would someone be able to look this over and tell me
2005 Jul 15
2
Strange problem with SIP and CAPI
Hi, I?ve strange problem when I?m making a call from SIP (Cisco 7960) to capi (Fritz PCI). When I call a national number, I?m hearing the ringtone when the called party is ringing but when I call an international number, I don?t hear the ringtone and I?ve a silence until the called party answers. Both call are going through the same extension. Here?s 2 log files, one with a national number and
2006 Jan 26
3
Chan_capi on builds 7955>8320 strangeness
Hello All, I am having an odd problem with Armin's chan-capi_cm on builds higher than 7955. It would seem that this happens on anything higher than 7955. What is happening is the isdn is ringing, then asterisk does a goto-if and just hangs. Asterisk itself is ok, but the isdn then rings out or busys out on the other side. Outgoing works fine, this only seems to effect incoming. I
2004 Dec 13
3
Busy message on ISDN cards?
Hi all, I'm new to asterisk and not too knowledgeable on ISDN, so please be gentle :) I have a dual-channel Eicon Diehl Diva card in a Debian Woody box with kernel 2.4.27, connecting to a Telstra (Australia) Onramp Home Highway ISDN line. I'm pretty certain the card and line both work since they've been used in this machine for PPP before this (but with an older kernel with DoV
2007 Mar 18
1
Choppy sound with chan_capi + Fritz Card USB
Hi everybody, I have a problem which I cannot eliminate on my own. Has anybody any idea for the following: I am using the asterisk-version from Debian-Testing (1.2.13) with the latest chan_capi (also tried an older version). When using the Capi-Channel, everything works fine except from the sound it sounds extremely choppy and is unusable :-( When e.g. capisuite is used for fax, everything
2004 Sep 15
1
Extension based call forwarding using capiECT
-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, I try to get callers forwarded to by mobile phone when they dial a certain digit. In my extensions.conf I have defined the following: [279xxxx] exten => s,1,SetLanguage(de) exten => s,2,Wait,5 exten => s,3,BackGround(demo-congrats) exten => s,4,Goto(boksa,#,1) exten => 3,1,VoiceMail,u1 exten => 4,1,VoicemailMain exten =>
2005 Mar 03
1
capi debugging
Hi, Regarding capi debug, I don't know how to translate reasons like 0x3302 or infos like 0. I didn't find any 'translator' googleing capi debugging. Do you know about any 'translator' for this or should I be as clever as to know what a reason 0x3302 is? What is this debug for if I can't interpret it? Kind regards, Victor. >From capi debug: == CAPI Call
2004 Feb 17
5
chan_capi problem
Hi to all I've mada up my mind and i tried to change from i4l to chan_capi, following some councelling from the gurus. I compiled it up, and when i try to load it in modules.conf, i get that wonderful message and Asterisk does not start: [chan_capi.so]Feb 17 09:21:40 WARNING[16384]: loader.c:239 ast_load_resource: /usr/lib/asterisk/modules/chan_capi.so: undefined symbol: ast_get_group Feb
2005 Sep 05
6
asterisk CAPI dial-in issues
Hello configuration as follows, dial-out works: capi.conf: [hfcpci] ;;PointToPoint (55512-0) isdnmode=MSN incomingmsn=* ;msn=61 controller=1 devices=2 context=incoming extensions.conf: [incoming] exten => _XX,1,Playback(demo-abouttotry) exten => _XX,n,Dial,SIP/xlite1 exten => _XX,n,HangUp When call is placed, the following debug info is shown, after the last line, it stalls until
2005 Oct 10
2
AVM Fritz! + chan_capi + mISDN + PTP
Hello everyone, I have been using an AVM Fritz! card with chan_capi and mISDN for quite a while in PTM mode and it was working finely. Now, I needed more DID/MSN, so I switched to PTP. But now nothing works anymore :( I am using Asterisk on Debian Sarge stable and installed Asterisk along with chan_capi from apt-get. I installed mISDN from the CVS of isdn4linux.de. It is : - Asterisk
2007 Jul 26
2
ISDN: Problems starting off
Hi, the first thing I did with Asterisk is listening to `demo-congrats' by Xlite on the same machine. This works perfectly. The config files are those shipped with the package. Now I want to listen to it over ISDN/Capi but I don't succeed. My `capi.conf' is like show in many tutorial on the web. In `extensions.conf' I just added the following lines: [capi-in] exten =>