similar to: PrimuX Cards with chan_capi-cm

Hi, I?ve strange problem when I?m making a call from SIP (Cisco 7960) to capi (Fritz PCI). When I call a national number, I?m hearing the ringtone when the called party is ringing but when I call an international number, I don?t hear the ringtone and I?ve a silence until the called party answers. Both call are going through the same extension. Here?s 2 log files, one with a national number and

Hi everybody, I have a problem which I cannot eliminate on my own. Has anybody any idea for the following: I am using the asterisk-version from Debian-Testing (1.2.13) with the latest chan_capi (also tried an older version). When using the Capi-Channel, everything works fine except from the sound it sounds extremely choppy and is unusable :-( When e.g. capisuite is used for fax, everything

Hi all, does anyone have capiECT working? I can't get it to work - please see my logfiles below. While using an * CVS version of late September and chan_capi-0.2.5 (I guess), it worked!!! (I know, never change a running system ... should've backuped ... etc.) Here's the setup: NT----AgfeoISDNPBX----AgfeoISDNPBX----AnalogPhones in between the two PBX I attached my * server with a

Hi, I tested the capi_chan with latest cvs of * and I have problems with Early-B3. The following dialstring works for me (without Early B3): exten => _0X.,1,Dial(CAPI/@22715291:${EXTEN:1}|30) But if I add the 'b' for using Early-B3 exten => _0X.,1,Dial(CAPI/@22715291:b${EXTEN:1}|30) nothing changes (no dialtone). If in this example the called party discards the call, there is no

Hello, I need to detect both fax and answer machine, and it should be valuable that the detection will be run by the Diva card itself. So : - I read Diva Documentation, and I found that the Diva could send some specific DTMF, if I had "[..] enabled [this functionnality] by the application for a designated controller through a manufacturer request command 9 [...]", but I didn't

I have a Diva Server BRI installed in a Debian system running Asterisk 1.2.22. When a call comes in the Background application plays a couple of times. Halfway through the second time, the call is disconnected (total time connected about 25 seconds). I've posted various configs below. Any advice on how to debug would be appreciated. We are located in New Zealand. CLI showing capi debug (just

Hi, I am having a problem with (Asterisk is crashing) with a Fritz card PCI / chan_capi. Receiving Calls from PSTN works, but outbound calls make asterisk crash (Speicherzugriffsfehler/Segmentation fault). The crash occurs upon dialing with the other phone not even ringing. I hereby ask if somebody reading this list can confirm or disprove my issue. Does anbody run a recent asterisk 2.6 with

Good day, The unusual thing about this problem is that it doesn't occur just during a CAPI call, or just during an IAX/SIP call. Only during IAX/CAPI I'm having some trouble with the CAPI interface and it only occurs when a call comes in on an IAX channel and goes out the CAPI interface. The capi debug in the asterisk console is below as well as the relevent parts of .conf files from

Hello everybody! happy new year ;-) I have a problem with inbound calls on my Diva Server PRI This is my problem: 2005-01-05 15:38:04 ERROR[31716]: chan_capi.c:1696 pipe_msg: did not find device for msn = 4132 capi.conf: [general] nationalprefix=0 internationalprefix=00 rxgain=0.8 txgain=0.8 language=de [interfaces] msn=4132 incomingmsn=* controller=1 context=demo mode=immediate

Hi, I've a Fritz card which was working fine, recently I changed hardware and my nightmare started. Now when I call someone through the chan_capi (0.3.5 or 0.4.0) it works fine but when I receive calls I always get hungup. Can someone please give some help? Here are the logs: *CLI> -- CONNECT_IND ID=001 #0x0000 LEN=0049 Controller/PLCI/NCCI = 0x101 CIPValue

I've the following setup : sip phone -> ser (auth and routing) -> asterisk with capi isdn when I call a pstn number everything works fine, but I can't hear anything till the called answer. this is the output from a test call : -- Executing Playtones("SIP/2.7.184.61-08152880", "dial") in new stack -- Executing Dial("SIP/2.7.184.61-08152880",

Hello, i have asterisk with chan_capi ( AVM Fritz card ) working, isdn line BRI, setup to point-to-multipoint. working fine, but when both channel on interfaces are used and somebody wants to call in - the response is "ha-la-li" - sounds like msn or called number does not exists. i think that right response should be - line busy tone... right ? can anybody tell me what is wrong ?

Hello List, because this is my first post to this list, i'd like to introduce myself. My name is Thorsten M?ller, 26 years old and live near Frankfurt/Main in germany. Okay, now to the reason for this posting: I just installed my first asterisk server (Debian 2.2 Kernel 2.4.18-686) with AVM ISDN Fritz PCI card (passive). I followed the configuration on http://voip-info.org and the

I have a problem receving calls via the ISDN line, using the followin components Asterisk 1.0.9 with asterisk@home chan_capi-cm-0.6 AVM Fritz card datalink protocol = point to multimode I can make calls out with no problems so the issue is only incoming calls. When I make the call from an external line to the ISDN line connected to asterisk, I get a busy signal after about 5 seconds. I have

Hello configuration as follows, dial-out works: capi.conf: [hfcpci] ;;PointToPoint (55512-0) isdnmode=MSN incomingmsn=* ;msn=61 controller=1 devices=2 context=incoming extensions.conf: [incoming] exten => _XX,1,Playback(demo-abouttotry) exten => _XX,n,Dial,SIP/xlite1 exten => _XX,n,HangUp When call is placed, the following debug info is shown, after the last line, it stalls until

Hi all, i have asterisk 1.0.9 with an Eicon Diva 4bri and chan_capi-cm-0.6. I have 2 NTBAs (one with did and one without). When using the one without did, i am able to place outgoing and incoming calls. When i use the NTBAs with did i have a layer 2 error. Anyone an idea? -- Executing Dial("SIP/2004-9634", "CAPI/g1/43XXXXXX") in new stack > data = g1/43XXXXXX

Hello, I did this post a long time ago but never solved the problem, so i'm trying again after something like 10 months, hopefully i'll find someone that found a solution ;-) When i call an external number that sends audio before call has been answered (like some PBX of public offices do here in italy), strange things happen: I'm using chan_capi, with Early B3 active, i can listen

Hi all, * was running ... I have a WT405P and an AVM C4 with chan_capi 0.3.4a Today chan_capi stopped working, without any changings at the system. It seems, that not * is the reason, because isdn-log also shows no calls. If I try to call * from outside via capi, I only get a busy. That is the try from inside to outside: stern01*CLI> -- data = @89930:0107901723168212 -- capi

Hi, whenever I include a "Ringing" Line in some Voicemail Extension I get an error when a call from the outside (via ISDN) comes in, but it works when an internal (SIP-phone) calls the extension. Here is my configuration for testing: ------------extensions.conf------------ [isdnext] ; strep external "101", our number and leave only extension exten =>

Hello Armin, hello List I'm trying to get chan_capi working with asterisk from debian stable (asterisk 1.0.7, the debian version number is 1:1.0.7.dfsg.1-2). I managed to get it compiled by providing my own version of ast_copy_string. This is an Austrian PTP line. I can do outgoing calls fine (no comprehensive tests yet). For incoming calls, I'm getting "No answer" on the