similar to: fax detection on TE406P

Hello, Now that we've had our new Digium TE406P card in production for 4 days we have discovered audio drop problems that happen randomly across all channels. Here's more about our setup: P4-3.2GHz 2GB ram Slackware Linux 10.1 with custom kernel 2.4.29 Asterisk 1.2beta1 Digium TE406P quad T1 card with the following attached: - 2 x RBS D4/AMI 24 channel T1s - 1 x RBS B8ZS/ESF 24 channel

Hi, I've installed an TE406p, asterisk1.2 on tyan opteron board. After installation there is no interrupts from TE406p. Is this board stable? Should i change * version to 1.0.9? Regards, Jason __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com

I changed from a TE410P to a TE411P and fax carriers weren't detected anymore ! I have tried everything (recompile zaptel+asterisk+spandsp ; echocancel=yes/no ; rxgain=0/txgain=0 ; increase Wait() ; ...), nothing worked. The only solution that worked for me was to install and use NVFaxDetect. HTH.

I am getting ready to purchase my first Digium card to start experimenting with Asterisk. Before I make my purchase, I wanted to make sure I'm not going to have issues with these cards (need to see what the specs are on my box, 5V or 3.3V PCI ). I will be using Asterisk @ Home, so will be Asterisk v1.0.9. I took a quick poke at the lists, and it appears several people have been having

Thanks to the great support at Rhino Equipment and Digium, this has finally been solved. I wanted to post the solution back to the list in case anyone else is having a similiar issue. I started by calling Rhino support so I could eliminate channel bank configuration as the issue. We were able to determine the channel bank and signalling were all working as expected. I then began to monitor

I am having a problem with asterisk not being stable enough for production use. I have two cards, the digium TE406P, and the TE410P. The TE410P is the primary card that I am using but I would like to move to the TE406P for the echo cancellation and more flexibility of PCI slots available. General config info: 3 PRIs, configured as such: span=1,2,0,esf,b8zs span=2,0,0,esf,b8zs

Hi, My configuration is pri----*(te405p)---iaxclient. My * version is 1.0.7 running on tyan dual opteron board. I have several problems. 1) inbound echo For outbound call(iaxclient-->pri), there is almost no echo. But for inbound(pri-->iaxclient), I can hear distinct echo. Can Sangoma a104 or digium te406p help this problem? 2)Today i received te406p. I know T1/E1 jumper. But how can i

I received a TE406P card from Digium yesterday and have done several tests on it and cannot get it working reliably with any Stable release or even CVS v1.0. What are other people that are using the TE406P card using for an Asterisk version? I tried 1.2.0 beta1 and it seemed to function well except for an unrelated issue with the beta release where the manager interface chokes under

Hi Guys, I need your recommendation which card to buy?The TE411P or TE406P do they have any difference?I check their brochures they are differ only when it comes to PCI slot voltages.Which card best to use?Btw,Il be using supermicro board with 3.3V and 5.5V?Will il be experiencing problem during the implementation later on if i choose the wrong PCI voltage options?Will it depends on

I just wanted to post here and let everyone know that the TE406P (quadspan T1/E1 with hardware echo can) kicks some serious ass. We've been running a PRI now for over a year with Asterisk (every single call in and out is through two Asterisk boxes, including faxes) and while the software based echo cancellation is more than adequate, we'd get the occassional "edgy" echo and

Hi, I cannot make my TDM2400P (with Echo Canceller module) detect faxes. I tried with a TDM400P and it worked at 80% (20% of faxes were lost). My test conf.files are: _zapata.conf_: context = inbound faxdetect = incoming language = it musiconhold = default signalling = fxs_ks callerid = "call_or_fax" channel => 1 extensions.conf: [inbound] exten => s,1,Answer exten =>

It works out that name "Unified t4xxp/t2xxp driver" is not accepted anymore by 2.6.13 kernel. Need to remove "/" for it to load properly > -----Original Message----- > From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users- > bounces@lists.digium.com] On Behalf Of Boris Bakchiev > Sent: Monday, 15 August 2005 18:17 > To:

I just implemented a system using a TE411P hardware echo cancellation card. Per Digium, I setup zaptel.conf, and zapata.conf the same way as I always have. To my surprise calls out to the PSTN had a terrible echo. 1 - 2 second delay, and quite clear. The echo was so bad that I had to remove the hardware echo cancellation module from the card. We are only using the 1st span of this card right

Guys, I'm trying to configure a TE406P with MFC/R2. here goes my zaptel.conf: span=1,0,0,ccs,hdb3,crc4 cas=1-15:1101 dchan=16 cas=17-31:1101 span=2,0,0,ccs,hdb3,crc4 cas=32-46:1101 dchan=47 cas=48-62:1101 The first strange behavior is that the: zap show status shows this: Description Alarms IRQ bpviol CRC4 T4XXP (PCI) Card 0 Span 1

Hi, Does anyone know if it's possible to have 1 port of TE406P to provide T1 PRI to other VoIP gateways? I am trying to provide T1 PRI to one of our old Clarent gateways to integrate it to Asterisk. Can anyone help? Thank you. Andy

Hi, I'm unable to load wct4xxp module for TE406P card. I've compiled 2.6.13-rc6, got latest CVS (as of today) of zaptel, but when I try to load the module I get this: kobject_register failed for Unified t4xxp/t2xxp driver (-13) [kobject_register+53/73] kobject_register+0x35/0x49 [bus_add_driver+62/153] bus_add_driver+0x3e/0x99 [driver_register+55/58] driver_register+0x37/0x3a

Does anyone know how to disable the VPM in software rather than removing the card altogether? The canceler isn't working as well as the software cancelers were. Aaron

Hi, I just read a pressrelease from VON that Digium will soon be releaseing a couple of new cards. What got me interested was: "The TE420P and TE415P support 128ms of G.168 (2002)-compliant echo cancellation across their entire 128 channels." Does anyone know when thease will be released and what they will cost when released? Thanks!

Forget the sound card. It isn't related. The subject above should have read 'TE405P No Voice Problem' or something similar. It appears to be a zaptel timing issue, but I have found a workaround. For those of you just tuning in, here is the story: I have a CentOS/Intel 865 box currently running Asterisk 1.2.7.1 and zap 1.2.5, both compiled from the source available off the main

Hello I just updated the kernel, dahdi-linux and dahdi-tools Im also using now asterisk 1.4.26.1 And im still with a red light (not RED/YELLOW anymore): [root at catumbela ~]# /etc/rc.d/init.d/dahdi status ### Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" (MASTER) HDB3/ RED 1 PRI CAS RED 2 PRI CAS RED 3 PRI CAS RED 4 PRI