similar to: Noise using TE410P & Rhino Channel Bank

TE410P card down. I have three (3) TE410P in one machine running asterisk with SS7. My problems started last week when one of my cards started switching to E1 every time after reboot. I set the following in dahdi.conf and that solve the problem. /etc/modprobe.d/ options wct4xxp t1e1override=0x00 Now all 4 ports on that card is down with Red Alarm. I tried rebooting the machine and

Hi list, We have been trying to configure a Quad Span T1 card in a system running RH9. We have followed the instructions in the Wiki and searched the mailing lists, but so far havent got any success. Cable is connected to the first span, and module is loaded. Without loading the module the LED glows in red colour, but the moment we load module, it goes off. (No red or green) . We ran zttool

I have a box with 12 T1s (4 Te410P cards). The PSTN provider is reporting slips and ask me to update the clock source. I have my system.conf set as the following but when I run dahdi_scan only the ports on Card 1 are showing up with syncsrc=1 system.conf : span=1,1,0,esf,b8zs bchan=2-24 mtp2=1 span=2,2,0,esf,b8zs bchan=26-48 mtp2=25 span=3,3,0,esf,b8zs bchan=49-72

Has anyone had any success with the Rhino CB-24? I can't get mine to work, I tried all the obvious settings. The cb-24 gets stuck at init ESF framing, as if it's not seeing the t1 card at all. It does get a t1 carrier (detecting voltage??) Help! Thanks.. Everything appears to look good on the server, I did: [zaptel.conf] span=1,0,0,esf,b8zs fxogs=1-24 [zapata.conf] signalling=fxo_gs

List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to

Greetings, According to the FAQ "When you load the module and have no circuit/channel bank the LED's should flash red" I get the "knight rider" lights before the module loads, but after the modules are loaded I don't get any lights, other equipment plugged in or not. The card has been on my shelf a while so I wonder if it needs a firmware upgrade ? Can the cards

Hi all, I've got a TE410p connected via T1 to four channel banks (2 FXO and 2 FXS), no PRIs. Some users are complaining that they hear clicks and pops on the FXS lines, generally when they pick up the phone it's noisy. This happens only after a while, e.g. after a fresh restart of everything, all is fine but after some time these noises start appearing. From what I've read on the

I am having a problem with asterisk not being stable enough for production use. I have two cards, the digium TE406P, and the TE410P. The TE410P is the primary card that I am using but I would like to move to the TE406P for the echo cancellation and more flexibility of PCI slots available. General config info: 3 PRIs, configured as such: span=1,2,0,esf,b8zs span=2,0,0,esf,b8zs

Hello, I am looking to buy a large number of TE410P cards for a big international project. I have studied the documentation and zaptel.conf and as result I have the following questions: 1. How do you switch the card from ISDN PRI TE to NT? This means from being configured as User Equipment (the PABX) to be Network Equipment (the Exchange). 2. How do you configure the card for E1 or T1? 3. In

I'm installing TE405P card. This is my zaptel.conf. -------------------------------------- span=1,0,0,ccs,hdb3,crc4 span=2,1,0,ccs,hdb3,crc4 span=3,0,0,ccs,hdb3,crc4 span=4,0,0,ccs,hdb3,crc4 loadzone = us defaultzone= us -------------------------------------- When i modprobe wct4xxp, -------------------------------------- PCI: Found IRQ 11 for device 02:0b.0 PCI: Sharing IRQ 11 with

Hi - We're moving up in the world to a PRI (Verizon), and I'm having some problems with it. I'm new to this PRI thing, though, so maybe I've just screwed up a simple config detail. I've got a TE410P on a Dell PE1600SC (ServerWorks Chipset). The card itself has a green light for the PRI, and Zttool shows Span1 as "OK". All I'm getting when I call into any

Hello All, I have a Digium Wildcard TE410P Quad-Span T1 Card, when I do connect T1 lines it goes in RED. When I do connect the same line on a different Server (Same Model T1 Card) it works fine. How do I examine/diagnose my T1 Card for any hardware failures. I heard about loopback test , how helpful it is? Here are my configuration /etc/zaptel.conf span=1,1,0,esf,b8zs

Hi all I'm trying to configure a TE410P in Europe with three E1s and a T1 channel bank (already bought in the US) to receive and make calls through *. I managed to get the E1s to work, but I'm having trouble with the channel bank (a Rhino). I have tried the bank in spans 1 and 4 changing jumpers in the card (always with no PRI connected, as I have no PRI where I'm testing now,

I have a T1 PRI from the telco and have been trying to get it to work with the wildcard T400P. I know framing and coding is esf and b8zs. what else should I be putting into the zaptel.conf and zapata.conf. Dave Anderson

I'm looking to install a system with 80 FXS analog phones. At this time the only cost effective solution is using a 4 port T1 card and addit 600 channel bank. Has anyone tried this solution? any good documents beside http://www.voip-info.org/wiki/index.php?page=Asterisk+hardware+channel+bank+check as far as i know, addit 600 T1 interface is not PRI (please correct me if i'm wrong) its CAS

I know this topic has been covered before - I just want to make sure I am understanding this correctly. | ------------------- | | | | T1 | Channel Bank | | ----------| | | | T1 Cross | | | | | | | | ------------------- -------------- | Asterisk | | | |

Hi, I have this strange problem I need some help with.. It appears that I have harddisk noise captured by a Digium TE410P card (Same problem on 2 identical machines..) The machines are two Compaq Proliant DL320 G3's... Does anyone else have this problem.. Kind Regards Claus Futtrup --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com).

Hello everyone, I'm using a TE410P, no irq sharing, and all extraneous devices disabled, such as USB, Parallel etc. I'm getting a few IRQ misses according to ZTTOOL. We're running a standard PRI_CPE interface and seem to be getting dropped calls, and errors on the D-CHANNEL occasionally. The circuit itself is very solid, it was in use on our old PBX just a few weeks ago, never

I am testing analog phone and fax machine plugged into Rhino Channel Bank which is connected to TE412P card. This site is in China. I am running RHEL 5, Asterisk 1.4.21.2, Zaptel 1.4.11 and libpri 1.4.4 I ran into a problem which is analog phone can hear dial tone and can make outgoing calls. Another phone (ether internal or external) can call the analog phone ***but the phone does not

We just switched from three x100p's to a te410p for handling our incoming/outbound calls. Everything works great, except incoming callers don't hear a ring while they are waiting for one of us to pick up. The phones themselves ring fine, but the caller doesn't hear anything until someone picks up, or it transfers to voicemail. Any clues as to what may be happening?