similar to: call wating and call transfer

Hi, Does anyone know how to tell Asterisk to transmit a switchhook flash? I have Asterisk attached to the ATA adapter of my legacy PBX, and some features of the ATA/PBX are supposed to be accessed using an analog telephone's switchhook flash or "link" button. I want to emulate this. - Mike

Hey all, posted this the other day, but re-read it & realized I didn't give enough info to be useful.. so I thought I'd try again.. I'm using AAH 2.0 (* 1.2.0) and am unable to transfer a call when I initiate the outgoing call. In AMPs general settings, I've tried changing the Dial command using tT but transfers are only available when I'm the recipient of the call, not

Hi list, I'm trying to attach a Avaya with Asterisk, call the extension 3241 to 1042 belonging to avaya, but only sounds rings and when I pick up the phone keeps ringing 08-14-13 07:26:17 AM-856ms Line = 18, Channel = 1, SIP Message = Response, Direction = From Switch, From = 3241 at 172.16.8.40, To = 1083 at 172.16.8.5, Response = 100 Trying 08-14-13 07:26:17 AM-857ms Line = 18, Channel =

We are using Bellsouth 8867 phones on our TDM400B FXS lines (asterisk-1.0.3). It has a "Voicemail" light, which appears to be MWI (according to the manual it works with voicemail from the telco that sends a FSK signal). The dialtone stutters when a line has voicemail, so I know that I have the mailbox setting right in zapata.conf, but the light doesn't go on. I am also getting

Hello. I am a spanish student, so excuse my English. I have this HW: - 2 X100P PCI with two analog lines plugged in. These lines are two extensions of a panasonic PBX. Zap/1 = X100P <-- analog line --> extension #237 PBX Panasonic Zap/2 = X100P <-- analog line --> extension #245 PBX Panasonic - 1 TDM20B with two analog telephones plugged in. Zap/3 = TDM20B

Another day, another apparant unexplained hardware incompatibility. I have a TE412P and a TDM400B living quite happily in a whitebox using an Intel motherboard: http://www.intel.com/design/servers/boards/se7230nh1-e/index.htm I tried to move to an IBM x3650 system. It uses a slightly newer chipset, but apparantly it's in the same family. The SE-7230 board has been EOL'd and the

Hi list, I'm wondering if it's possible to transfer a call that is still ringing??? Actually, the problem is that my telco provider doesn't offer an uniform method for answer/disconnection supervision, and by that I mean, some of it's line (I think) offer a polarity reversal, but other lines (of the same service provider) do not offer anything at all, so the answer of a call

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all! I'm trying to doing a transfer from an analog extension to a SIP extension but until the moment I was not successful. I was testing both the recall key and uncomment the following lines in the features.conf file: blindxfer => #1 atxfer => *2 verifying previously that the extension uses the arguments "tT" with the Dial

I moved my TDM400B cards (first two cards are 40's, third is a 31, last is an 04) from one computer to another, copied all the config files, and now the LED on the line 11 - third line of the third card doesn't go on (it used to on the previous computer). I can get by telling * not to use this line for now but does anyone have any suggestions for getting it to work? Unseat and

I have: RedHat 9.0 TDM40B asterisk-0.9.0 compiled from sources zaptel-0.9.1 likewise /etc/zaptel.conf contains fxoks=1-4 loadzone = us defaultzone=us loaded modules zaptel and wcfxs /etc/askterisk/zapata.conf contains [channels] language = en signalling = fxo_ks context = phones channel => 1-4 /etc/askterisk/extensions.conf contains [general]

Hi. I have the following line in the default context of all my internal extensions: exten => 9876,1,Transfer(125) When I dial extension 9876 from any sip phone, * dutifully transferrs it to extension 125, which is just what I want. Unfortunately when I dial 9786 from my Zap connected analogue phone, the transfer doesn't go through and the dialplan drops through to a hangup. debug

Is there a cable length limit to use with a fxsmod (TDM400B) ? I noticed that if I use a very long cable 148 feet, I can hear some parasite : I hear the radio ! If I use a short cable, there is no problem... Thanks for help, St?phane HENRY

I'm a bit confused on how to setup Zaptel.conf and Zapata.conf when there is a TDM400P and a TE410P installed after upgrade. The TDM400P has 2 FXS in position 1 & 2 and 1 FXO in the fourth position. I see boot, WCT4xxP loading first and WCFXS loading second. According to my understanding, given above, the TE410P should be configured first, then the TDM400P. However, I'm not sure

I'm struggling to get my dialplan to work with a simple analog fax machine. I have TDM400B zaptel card with an FXO and FXS port. I have the FXO port connected to the POTS machine and the FAX machine connected to the FXS port. The FAX machine itself works fine, I can FAX outgoing messages fine. I can also dial the FAX extension from the internal context, the FAX machine answers and I

Hi, I am trying to configure * 1.0.7 box with a Digium Wildcard TE110P T1/E1 and libunicall latest code. All libs compiled successfully and the E1 have a green light! I am able to receive a call (or at least) testcall shows some information when an incoming call is received so the drivers and basic configuration is working. My * box has 2 cards, one TDM400B (2 fxs and 2 fxo) and one TE110P

I have just realized while trying to research asterisk not acking incoming calls that the tdm400b card is stamped rev H, but when I issue the zap show status command in the manager interface, it indicates Wildcard TDM400P REV E/F Board 1 Which do I believe?? -- Best Regards Greg Cirino Spam and Virus Free Email included with every email account Cirelle Enterprises Inc. 25 Indian Rock Rd

Hello List, Im just dipping my feet into the asterisk world, and im having major fxo problems Im running Asterisk (from svn) + libpri (from svn) + asterisk-addons (from svn) + asterisk gui (svn 1.4 branch) + zaptel (svn 1.4) on a Debian Etch box, with 1gb ram, running all of the services for my home server (web / db / music server etc), and i would like to run my PSTN line from Kingston Comms,

I have a Linksys PAP2. Identical setups for the two channels in both the unit and in Asterisk. In particular, both channels enable g729 and set it as the preferred codec, and have disallow=all and allow=g729 in sip.conf. If we make a call on one channel, it works (and uses g729), but if we make a call on the other channel when the first one is still connected, it fails. We have three g729

I'm rolling out an installation with snom 360s in the near future. Simple SOHO configuration, 3 FXOs hanging off a TDM400B, 4 snom 360s, a snom 200, some variant of IAX softphone, and an IAXy or Sipura 2002. I have the 360's set up to subscribe and notify for the line use lights, which works like a charm for interoffice calling (between the 360's, anyway. The IAXy, 200 and,

I just had to move all my disk drives and PCI cards, including the Digium TDM400P, into a new box when the motherboard died. Now that the new box is up and running, my FXS ports no longer work although the FXO port does. I am hoping someone can help me diagnose and debug. I am running Fedora 8, asterisk asterisk-1.4.21, and zaptel-1.4.9 . Yes, I realize that this is old software and that zaptel