similar to: TDM400P Dialing Out - "Cannot be completed as dialed"

Details: Asterisk 1.0.9 Zaptel 1.0 Dell P3 1ghz with X100P Clone Location: India This is an interesting issue where when I open up ZTMonitor, it shows the RX as being on. It seems that Zaptel doesn't know to hang up the line so after a couple of hours when the telecom cuts the line, everythign stops working. Things I've tried include playing with the zaptel.conf, trying zaptel v1.2(with

Hello... I have a big problem with asterisk. Every time i make a call asterisk does not bridge the zap channels. The zap channel from which i'm calling remains in state:ring and applicaton:dial and the zap channel with the external line configured remains in state:dialling an Application:AppDial. Zap/20-1 agentie s 1 Dialing AppDial (Outgoing Line) 09399 (None) Zap/9-1 int_omg 09399 5 Ring

Hi, I've got a problem with my asterisk set up which has been going on for a while (months). I'm currently running 1.2.7.1 on a gentoo box with the topology below: +-----+ PSTN ---------+ * +------------- Service Provider (wctdm400p) +-+-+-+ IAX | | | | FXS --+ +-- SIP (cisco 7940)

When I reload the config, I see this error in the CLI. However, I don't see what I have done wrong: == Parsing '/etc/asterisk/zapata.conf': Found May 30 16:38:42 WARNING[12630]: chan_zap.c:10088 setup_zap: Ignoring signalling -- Reconfigured channel 1, FXO Kewlstart signalling May 30 16:38:42 WARNING[12630]: chan_zap.c:10088 setup_zap: Ignoring signalling -- Reconfigured

Hi all, I have TDM2406E with 24FXO ports connecting to 10 POTS line sitting in my office. the out going calls symptom like when called party pickup the phone but the calling party still hearing the ring tone from the IP phone. Please light me up. it been many sleepless night by googling around trying to get the right answers. The digium card running on Intel 915G chipset. Below are my zaptel

I'm a bit confused on how to setup Zaptel.conf and Zapata.conf when there is a TDM400P and a TE410P installed after upgrade. The TDM400P has 2 FXS in position 1 & 2 and 1 FXO in the fourth position. I see boot, WCT4xxP loading first and WCFXS loading second. According to my understanding, given above, the TE410P should be configured first, then the TDM400P. However, I'm not sure

I'm having real problems with my connection to BT, it is a home line, but after a while it sets an alarm and only a restart of asterisk resets it could some one look at the below configs and suggest any changes to make this more reliable Thanks for your help Robb asterisk version 1.6.1.10 dahdi version SVN-trunk-r7445 dahdi_scan active=yes alarms=OK description=Wildcard TDM400P REV I

I have a Digium TDM400p (1 FXO, 1 FXS) with the FXS module connected to a standard analog handset with caller id display (US caller ID). Although it appears that caller id information is coming into asterisk (it shows up in voicemail), I can not get it to display on the analog handset. Is there anything special I need to do to send the caller id info out the FXS port? I've tried a few

Just to make sure this isn't a typo in your original email... Is this example from your zapata.conf? Also, the extension you have shown are in extensions.conf not zapata.conf correct? Here is an example of a good zapata.conf.... [channels] language=en busydetect=yes faxdetect=both busycount=7 relaxdtmf=yes callwaiting=yes callwaitingcallerid=yes useincomingcalleridonzaptransfer=yes

Hello all, Recently I just instaled asterisk-1.2.14, zaptel-1.2.12, libpri-1.2.4 and Freepbx v.2.2.0. My zapata.conf look like this, (Pasted bellow) The problem is that the asterisk never send the callerID to the phones. I just take a look to the cdr database an there is no callerid too. I do not know why the calledID is not receibed. All this FXO ports are conected to a mobile lines and if I

Hi all, I'm trying to install a TDM400P card, and I need some help. Please, see below... after dmesg command: [root@voip root]# dmesg via82cxxx: board #1 at 0xD800, IRQ 5 Zapata Telephony Interface Registered on major 196 PCI: Found IRQ 3 for device 00:09.0 PCI: Sharing IRQ 3 with 00:10.1 Freshmaker version: 71 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1:

Err, stupid me. Seems like the phone is hungup, but when I start ztmonitor, the line is picked up. I guess the line in India is pretty loud b/c the RX bounces off the charts, changed it to (-4) and all my problems are solved. Regards, Min Chang On 4/14/06, Kyle Sexton <ks@mocker.org> wrote: > > Have you tried putting a Hangup in your extensions.conf? > > > > On 4/13/06,

Hello, I've one astribank with 8 FXO unit and 8 pstn lines connected to the astribank. When I receive calls on my ipphone I get always Unknown callerid. It's is possible to receive the callerid from the lines on the astribank unit? This is my config: [channels] language=es context=from-zaptel signalling=fxs_ks ;rxwink=300 usecallerid=yes callerid=asreceived ;cidsignalling=bell

We're rolling out Cisco 7940 phones, linked to *, which is running a TE405p EuroISDN. We have 2 ISDN lines, one we had for testing, and one for general (40+ users) use. During the testing phase, we had 10 phones linked to the second ISDN line, and there were no problems with echo at all. Lucky me. However, since we have started rolling out, we've had quite loud complaints that there is

All, I've recently installed a TDM400P and am unable to get it working. It has four FXO modules on it. What I would like to do is have the first two ports as inbound from pstn and have them ring the last two ports which will be connected to regular analog phones. In Zaptel.conf I have: fxsks=1-4 In Zaptel.conf [channels] context=default switchtype=national rxwink=300 ;

I have 2 Digium 4 port FXO cards in my system. The system is a P4 2.4Ghz, 512MB RAM, Promise FastTrax 100 TX2 Pro Raid, 80GB RAID1 for storage - whitebox - running RedHat 9. With pretty much any CVS HEAD version we are getting, what I will call, "phantom" calls on some lines. What I mean by a phantom call is that the line will ring, Asterisk will log that the Zap channel has been

Hi, I'm installing an Asterisk box with a TDM2400P in Brazil. I can make analog phones work while lines are not working. Since I do not know anything about brazilian lines, is there anybody who can tell me what is wrong/missing in my conf files (below)? TIA Giorgio _zaptel.conf:_ fxoks=9-16 fxsks=17-24 defaultzone=br loadzone=br* * _zapata.conf:_ context = inbound_zap echocancel = 128

Hi all, I'm trying to install a TDM400P card, and I need some help. Please, see below... after dmesg command: [root@voip root]# dmesg via82cxxx: board #1 at 0xD800, IRQ 5 Zapata Telephony Interface Registered on major 196 PCI: Found IRQ 3 for device 00:09.0 PCI: Sharing IRQ 3 with 00:10.1 Freshmaker version: 71 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1:

I'm having some trouble dialing phone numbers in Argentina with Digium Zaptel cards. Does anyone have some sample configuration that works with Digium TDM04B cards in Argentina? I'm mainly referring to the /etc/zaptel.conf and /etc/asterisk/zapata.conf. I have two Zaptel cards: the first one has 1 FXS port and 3 FXO ports; the second one has 4 FXO ports. My current configuration is

Hello, I have a TDM400P with 4 FXO ports, currently using three. When sending or receiving calls on this card, there is a nearly constant popping/clicking sound, it is related to the echo cancellation?. I adjusted my gains properly, but to no avail. I even found that setting echotraining=no in zapata.conf didn't change the scenario at all. I've plugged analog handsets into the