Displaying 20 results from an estimated 20000 matches similar to: "TE110P reset"
2007 Feb 13
4
Nortel 81C MSDL Trunking to Asterisk TE110P, Nortel Resetting PRI Channels
We are currently working to trunk from a Nortel 81C to an Asterisk
Server 1.4 running on Red Hat Linux. We have two PRI trunks which work
with the exception of the clock slips, which is causing the Nortel to
reset the PRIs once a hour. Thanks for any suggestions.
81C MSDL Asterisk Digium
TE110P
REQ prt
TYPE adan dch 10
2005 Feb 09
1
SIP ActiveX
I search a ActiveX to develop one softphone SIP with codec G723. Who can
help me?
Thank?s
Jo?o Carlos Moura
2007 Feb 27
5
TE110P: Error ==> Asterisk died with code 1.
Running Asterisk 1.2.9. I just installed a TE110P card and configured
zaptel.conf & zapata.conf. The config files look right to me but I'm
getting the following error when trying to start asterisk:
Asterisk died with code 1.
Automatically restarting Asterisk.
Does anyone have any idea what is wrong with this configuration??
Thanks in advance!!!
Here's my config files:
zaptel.conf
2005 Aug 22
2
TE110P problem
Im using a TE110P as a trunk to a Panasonic KD-500 everything works
well.....but Im having this problem where one of the channels becomes
blocked with a partial phone number after about two days. So if the
channel that becomes blocked is channels 23 no calls can get in. If the
channel that gets blocked is 22 then one call can get in. The only way
to clear this is to reboot the server.
This
2005 Aug 08
4
TE110P flashing red/green when PRI connected
Hi
I'm having difficulties getting up my TE110P (running as a E1) when I connect it to the PRI. If I start the server with a loopback connector everything seems fine and the led is green but when I connect it to the PRI the flashing starts ....
I can't seem to find anything in the log that suggests what could be wrong
.....Aug 8 11:33:00 DEBUG[1369]: Updated conferencing on 31,
2005 Jul 05
1
Newbie question reg. Asterisk and Channel Access Bank I and TE110p
Hi,
I have some problem to get this setup working. I have a CAC Channel
Banl I, with FXO and an Asterisk box ( I am using Asterisk@Home 1.2)
and I have a TE110p installed in this box.
What I want to do is, just to be able to dial one of those lines that
already are connected to the channel bank, and transfer that call
through TE110p and Asterisk to a user agent somewhere through
Internet.
2006 Apr 04
1
Ideal setup for PRI/T1 and TE110P
Hi all, I'm sure something similar has been discussed, but one can only
wade through the archives for so long.
I'm setting up a T1 and my telco has a bunch of questions it wants me to
answer. I know much of the TE110p is configurable to do any of this, but
I wanted to know if there is an optimal or preferred setup.
Any help would be appreciated. Here is the quiz my telco is giving me:
2006 Mar 02
1
Toshiba DK424 / Asterisk / DTMF problems
I have a Toshiba DK424 connected via T1 E&M to a TE110P card.
Intermittently when a user dials a number I am getting 'getdtmf' errors on
the Ast server and the calls do not go through. If they dial the number
once or twice more, it works fine and I receive no DTMF problems.
On another note, end users are complaining about intermittent disconnects.
T1 is ESF/B8ZS - 24 chan. Other
2006 Apr 04
1
Ideal Setup for T1/PRI and TE110P - second try
Hi all, I'm sure something similar has been discussed, but one can only
wade through the archives for so long.
I'm setting up a T1 and my telco has a bunch of questions it wants me to
answer. I know much of the TE110p is configurable to do any of this, but
I wanted to know if there is an optimal or preferred setup.
Any help would be appreciated. Here is the quiz my telco is giving me:
2005 Jun 06
5
IRQ Problems
Hello
I just installed a TE110P in a Dell Poweredge 750 (rackmount), which
is connected via crossover T1 cable to a adit 600. Anyway, I've
encountered an array of errors, which I believe I have narrowed down
to the 22 IRQ misses I encounter on zttool. I've noticed that the
te110p and the usb device share an IRQ. Could that be the source of my
woes? Would disabling the usb device in the
2007 Jan 09
8
Problem with zaptel drivers or card
I have an Asterisk box running Fedora Core 4, Asterisk 1.4, Lippri, 1.4, and
Zaptel 1.4
The Digium cards installed are TDM2400 and TE110P.
Everything was working fine until I upgraded to zaptel 1.2.12 from 1.2.9
Now when I run ztcfg I get the following error message:
(CAS signalling on span 2 conflicts with Clear channel on channel 40)
--NOTE: signaling was spelled wrong in the error
2005 Apr 22
4
TE11OP -> Mitel 200Sx??
Hello all. I just received a TE110P and am trying to hook it to my Mitel 200SX has anyone successfully done this? My configuration is as follows.
Asterisk -> TE110P ->Kentrox (csu/dsu) -> Mitel T1 Card.
All I get is a blinking yellow on my TE110P card and an alarm on my Mitel. T1 card.
Any advice would be great.
Zaptel.conf
span=1,0,1,d4,ami
e&m=1-23
dchan=24
2005 Aug 30
1
TE110p and E1
Hi All,
I have configure my Asterisk as follow (using Asterisk@home):
[zaptel.conf]
span=1,1,0,ccs,hdb3,yellow
bchan=1-15,17-31
dchan=16
loadzone = uk
defaultzone=uk
[zapata.conf]
[channels]
switchtype=euroisdn
pridialplan=local
prilocaldialplan=local
internationalprefix=00
nationalprefix=0
usecallingpres=yes
busydetect=no ; not need on pri
callprogress=no ; was yes but wiki says experimatley
2005 Mar 17
2
TE110p card with Euro ISDN (Ericsson switch)
I am trying to use TE110p card for Euro ISDN with Ericsson AMS switch. I
consistently get one of the following errors:
PRI got event: HDLC Abort (6) on Primary D-channel of span 1
or
PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1
My zaptel.conf file:
--------------------------------
span=1,0,0,ccs,hdb3,crc4
bchan=1-15,17-31
dchan=16
loadzone=us
defaultzone=us
2006 Nov 22
5
TE110P and TDM400P
Hello all. I have here a TE110P (configured as E1) and a TDM400P (with four X100P - FXS). Both boards are recognized by the operating system as showed above:
0000:08:00.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface
Subsystem: Unknown device b1d9:0003
Flags: bus master, medium devsel, latency 64, IRQ 169
I/O ports at e800 [size=256]
2005 Mar 18
1
Te110P initial installation problems ?
Hi,
thank you for last info. we've tried to use te110p but failed. We're quite
surprised that cable wasn't included with the card as any documentation, at
least on HW setup and installation, yet cable pinout for connection to PRI
interfaces....
1. We have followed instructions on your site and from Beronet guide, but
card just keeps blinking and nothing happens (also no useful
2005 Feb 22
1
Astersik CVS HEAD + T1 e&m wink + IAX client doesnt detect call answered on Zap channel
Hello,
I've got very annoying behaviour from our asterisk PBX.
We have 12 channels T1 e&m wink start for TDM and using iax softphones
internally (iaxcomm, but tried firefly-thirdparty and discarded for
bad sound quality).
Slackware 9.1 w/ kernel 2.4.26+ digium TE110P card.
In some cases when call is placed from softphone to TDM, system does
not detect call answered on Zap channel and
2007 Sep 05
4
ztcfg error : TE110p error with " CAS signalling on span 1 conflicts with HDLC with ...
Dear All,
I'm integrating avaya commuication manager difinity ver 1.0 with asterisk
using B2B E1. following are the details of my H/W, zaptel configs and
software installed.
Digium TE110p
asterisk 1.2.19
cent OS 4.4
zaptel 1.2.18
libpri 1.2.4
etc/zaptel.conf
span=1,0,0,cas,hdb3
bchan=1-15,17-31
dchan=16
when i ztcfg -vvv im having this error message and the E1 is not getting up.
"cas
2003 Aug 18
8
PRI Question
I managed to get Asterisk working with my PBX using T1, now I am moving
on to trying to make PRI work.
I have my zaptel.conf and zapata.conf configured as follows:
Zaptel.conf:
span=1,1,0,esf,b8zs
bchan=1-23
dchan=24
loadzone=us
defaultzone=us
Zapata.conf:
[channels]
transfer=yes
immediate=yes
callprogress=yes
language=en
context=default
switchtype=national
signalling=pri_net
group=1
2007 Jun 14
1
TDM400p and te110p configuration.
Dear users.
My current setup uses a euroISDN E1 with 8 cahnnels for incoming and outgoing calls from a digium te110p.
Currently all phones use SIP.
However, I need to add some faxes lines and some POS credit card machines. These will require POTS lines with a fixed DDI.
I have purchased the tdm400p and 4 FXS modules.
My problem is with the zaptel.conf and zapata.conf.
I am a little confused as