similar to: Zapata help needed howto configure nationalprefix for a single card

has anyone an idea how to display incoming national/international isdn-pstn-calls correctly to internal isdn AND sccp/sip-phones ? without nationalprefix=0 and internationalprefix=00 I get incoming phone numbers correctly on isdn-phones but the leading zero's are stripped of for non-isdn phones when I set this prefixes inside zapata.conf my internal isdn-phones get this prefix twice...

Hi, I'm using a Junghanns Quadbri ISDN card on some lines from the Austrian Telekom. Things are working, the only missing stuff is to add a "0" as a prefix to each incoming call, to make it possible to answer missed call lists. I'm using the 0 as the prefix for outside lines. I've experimented a little with the prefix settings in zapata.conf, but without success:

Asterisk 1.8.4-rc2 (and 1.8.3) DAHDI Version: 2.4.1.2 libpri version: 1.4.12-beta3 We are having a problem with getting the nationalprefix option of chan_dahdi.conf to work. National calls do not have a "1" added to them when nationalprefix=1. The PRI debug shows the call coming in as a National Call, but the dialplan sees the call without a 1. chan_dahdi.conf: <snip>

Hi All ... I'm running Asterisk 1.2.13-BRIstuffed-0.3.0-PRE-1v which has a Junghanns QuadBri card in it (lspci reports Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01)) I have a regular KPN ISDN2 Line connected which works fine with the the zapata.conf below. However, I also have a new KPN ISDN Mutli (meervoudig) line (PBAX-Group), which works fine for incoming calls,

And I'll resend this one too. Silly scalix. --Rob -----Original Message----- From: Rob Thomas Sent: Thursday, 22 June 2006 12:19 AM To: 'Asterisk Users Mailing List - Non-Commercial Discussion' Subject: RE: [Asterisk-Users] zapata.conf: recent changes? Looks like you've stopped compiling libpri. All those options that are being ignored, are being ignored because they're

Hi list, After upgrading from Asterisk v1.2 to v1.4.14, all kinds Zaptel error messages related to my HFC-S PCI card disappeared, but now I can't access the card's resources because it always seems to be busy. Any idea why? Thanks, Jaap PS -- Below is some info regarding my configuration. =========================== Zaptel version: 1.4.7 (incl. firmware and modules). OS: Debian

Mine is very similar: i don't have echocancelwhenbridged=yes because it seems work only on TDM, is it ? And in Italy, I often have set pridialplan = unknown About echo I have some problems, but only at the beginning of the call. After 3-4 seconds the echo became almost null, specially with snom 190; with pa168s and ywh10 I have again some problem, the echo come up also after 1 minute of

Hi, after a few of upgrades, I noticed these messages in full debug log: Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring switchtype Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring pridialplan Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring prilocaldialplan Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring overlapdial Jun 21 12:58:11 WARNING[27273] chan_zap.c: Ignoring

Hi; I've been asked to take a (remote) look at an Asterisk@home system running asterisk 1.0.9 on Centos 3.5. It's running chan_capi-0.3.5 It has an AVM c2 ISDN card which is plugged into what I believe to be a couple of BT ISDN2e "System Access" (i.e. point to point) connections. We've placed a support call to BT to find out how these lines are actually provisioned, but

Hi, I have installed Asterisk 1.4 with mISDN with the install-asterisk.tar.gz script from beronet.com. On my system I have two cards, one a AVM Frit!Card Pci 2.0 and one HFC-S chip. I know both to work well with mISDN on my system from a previous installation. Now however, the AVM card works well at first glance, i.e. it "registers" incoming calls and works through the asterisk

Hi list, Now that I've got my Asterisk server to recognize my HFC-PCI card, I've run into some serious problems. The first thing I noticed was this message that would show up every five seconds on the CLI: Dec 27 15:46:42 WARNING[12484]: chan_zap.c:2512 pri_find_dchan: No D-channels available! Using Primary channel 3 as D-channel anyway! == Primary D-Channel on span 1 down

Hi all, I have a problem with my beronet card with 2 isdn. I think drivers and Asterisk are ok but the red led on the card always blinking. The card is connected with PBX. I post some conf: [root@gateway ~]# misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> Layer 4 protocol 0x04000001 is detected, but not allowed for TE lib. ->

Hi, I have just installed a Sirrux PC140 card for the first time. Managed to build the drivers and get * to load them on FC4, but it does not work. It seems that layer1 in the ISDN is not even activated. The same ISDN lines connected to a Samsung DCS works so it is not the lines. I am including my sirrix.conf and the output of some of the * Srx commands below. Any pointers would be

Hi, I'm trying to connect quadbri between powered ISDN phone and ISDN line: ISDN <---1---> TE - * - NT <--2--> Phone I use quadbri, suse 9.2 and latest 0.2.0-RC7k bristuff. I've used sample settings provided with package, but do get strange error (I think that I have wrong setting for P2P or P2MP setting and cables 1 and 2). If I connect phone to ISDN with straight cable

Hi, I have an asterisk installation with 2 E1 cards Software version is Asterisk 1.2.6 Libpri 1.2.2 Zaptel 1.2.5 I'm having problem with fax transmission, let me explain better my setup: My fist TE110P E1 card is connected to the telco line the second TE110P E1 one to an Nexspan PBX so the server is basically sitting between the line, and the pbx. every call coming from the line is

Hi, I'm using a ISDN-30 E1 line from KPN Belgium. The challenge is to get a correct CallerID on outgoing lines. When I put this in my dialplan: exten => _0.,1,Set(TEMPVAR=${CALLERID(num):1}) exten => _0.,2,Set(CALLERID(num)=144622${TEMPVAR}) exten => _0.,3,NoOp(${CALLERID(num)}) exten => _0.,4,Dial(Zap/g1/${EXTEN:1},,) The resulting CallerID is accepted by the telco, but on

I tried to setup an PBX System with the following parties: 1. SIP Phones 2. One AVM ISDN Card with CHAN_CAPI for Outbound dialing and receiving external calls 3. One HFC-S PCI Card in NT-Mode with ZapHfc for physical ISDN Phones. 1+2 work perfect I have problems with part 3 Card is working, drivers loading fine, asterisk initializes chan_zap without problems. Demo did work. My problem is

Hi all, I really hope that you guys can help, because I've been tearing my hair out for the past 5 hours on this one. I have a Zaphfc (BRI) card in TE mode connected to the S-Bus of a Nortel Meridian phone system. Phone calls from the Nortel to say MSN 510 are correctly being sent to the right SIP phone. When asterisk dials say Zap/g2/224 (a Nortel internal extension) the call goes

Hi, I am using asterisk 1.2.5 and have some problems with asterisk connected with an E1 card to our PRI. Dialling in and out generally works. When someone dials in from a mobile phone, all numbers are sent as a block, and the called extension rings as intended. when someone picks up his phone handset, waits for a dial tone, and then dials in manually, the call will be redirected to the

Does anyone know, how I can increase the timout value for the ISDN implses, so asterisk waits for the extension on the ISDN channel? Regards, martin My zapata.conf: [trunkgroups] [channels] language=de pridialplan=local prilocaldialplan=local nationalprefix = 00 internationalprefix = 000 ; trust user provided callerid (clip no screening)? pritrustusercid = yes ; hidecallerid=no