similar to: Setting wcte11xp card to use IRQ

I have a X100P and a TE110P in my Asterisk box. I can either get the X100P or the TE110P to work, but never both. Here's my zaptel.conf span=1,0,0,d4,ami e&m=1-24 fxsls=25 When I load wcte11xp and wcfxo, I will get this error. [root at asterix etc]# modprobe wcte11xp ZT_CHANCONFIG failed on channel 25: No such device or address (6) /lib/modules/2.4.20-8/misc/wcte11xp.o: post-install

Hello List, i am trying to set up an * box with a debian 2.6.10 Kernel. the compilation of asterisk and the zaptel drivers worked almost perfectly. so i did modprobe zaptel modprobe wcte11xp (which is the correct driver for my card) ztcfg -v and this results in ZT_SPANCONFIG failed on span 1: No such device or address (6) I don?t have any ideas whats wrong. google was no help, checking sources

Is it true that asterisk 1.2.6 does not use mpg123? I just installed asterisk 1.2.6 and while I do have music on hold (through format_mp3?) I do not have an mpg123 process running. I seem to be having serious audio issues when going through one of my providers (and just through that provider) when using mp3 for hold music, however when using wav files it is fine. The processor is only at about

Hi, I' ve just connected a carte X100M to my asterisk server running zaptel-1.2.5, libpri-1.2.2 and asterisk-1.2.6 on SUSE 10.0. When I make modprobe wcfxo and modprobe zaptel I haven't any error, I have also chan_zap.so module existing in /usr/lib/asterisk/modules. But, when i run ztcfg, it shows me this: Zaptel Configuration ====================== Channel map: 0 channels configured.

Greetings all Grandstream released a new firmware and it seems like the speaker phone problem has been fixed. However we updated to firmware 1.0.1.12<http://1.0.1.12>to fix the echo problem but found other problems were now created. The worst of these new problems is that the whole phone starts degrading, the volume starts getting lower and lower. The ringing starts fading and the calls

Has anyone had any experience with the Asterisk on a SuSe 10 platform? I'm currently using FC3 but because we use SuSe within other parts of the business I'm being pushed to changed the OS. Regards Lee ########################################### This message has been scanned by F-Secure Anti-Virus for Microsoft Exchange. For more information, connect to http://www.f-secure.com/

Can anyone recommend CRM software with a link into Asterisk? I would like a pop up on caller ID if possible. I've played with the FOP and SugarCRM but can't get them working together. Regards Lee -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050818/e71c34a3/attachment.htm

Hi I'm trying to get a Digium TE110P card working but as soon as I load the module with modprobe wcte11xp the sound stops working for incoming calls (SIP and IAX). I haven't even started to configure the card. Running ztcfg and restarting asterisk doesn't help. After unloading with rmmod wcte11xp the sound comes back for new calls I'm using asterisk 1.2.4, libpri 1.2.2 and

I installed zaptel 1.2.17 and shortly afterwards got a problem of calls not clearing properly. I ran dmesg which showed Unable to handle kernel NULL pointer dereference at virtual address 0000009c printing eip: f8a79fa8 *pde = 00000000 Oops: 0000 [#1] Modules linked in: zttranscode button battery ac ipv6 edd wcte11xp zaptel crc_ccitt i2c_i801 i2c_core tg3 generic shpchp pci_hotplug

I am having problems loading the zaphfc from bristuff and wcte11xp drivers at the same time. If I load zaphfc then all works fine. If I then load wcte11xp, the card using the zaphfc doesn't pick up calls anymore. I am using bristuff 0.2.0-RC5. Anyone else seen this problem, know of a fix, or can tell me what I am doing wrong? Thanks My zaptel.conf: # hfc-s pci a span definition # most of

Hello! I discovered, that I'm unable to load ther kernel module under 2.4.28. Before that I had 2.4.26 and tryed to upgrade the kernel to 2.4.28. After restart (reboot - soft restart) I can't load the module. When I go back to 2.4.26 and try to load the module, I'm getting the same problem. Only turning off/on helps. What can I do? It's very annoying because the box is in hosting

I can either get the TE100P working or the 3 X100P clones working, but never both. I have the TE100P connected to a channel bank, and X100P clones to lines from the phone company. This is my zaptel.conf span=1,1,0,d4,ami fxsks=1-24 loadzone=us fxols=25-27 loadzone=us I then do [root@asterix root]# modprobe zaptel [root@asterix root]# modprobe wcte11xp ZT_CHANCONFIG failed on channel

Does anyone have any ideas why my recently updated * 1.2.5 system should spawn multiple * process at seemingly random intervals? Regards L:ee ########################################### This message has been scanned by F-Secure Anti-Virus for Microsoft Exchange. For more information, connect to http://www.f-secure.com/ -------------- next part -------------- An HTML attachment was scrubbed...

Hi folks, I've already searched the mailing list but no one else seems to have my same problem. I'm using Asterisk with the following configuration: Fedora Core 4 (but I also tried Fedora 3) 1 Digium TE110P 1 TDM40B 1 HFC-S 'Cologne' bristuff 0.2.0-RC8o (zaptel 1.0.9.2) I compiled right, I can load kernel modules but when I try to unload wcte11xp module (the one

Hi, It seems like my ATA is making a ringing noise... (as it used to), but now (After the upgrade from 1.0.7 to 1.2) asterisk also is either making the ringing, or passing the PRI ringing from the telco on to me. Any suggestions on how to fix this?

Excuse my ignorance here, but I am desperately trying to isolate the IRQ for my TE110P card (shown below as t1xxp) Ive gone into my bios and disabled all usb , parallel, serial and some other devices, those that I needed to keep, I have moved off of IRQ 10 and onto IRQ 5, but everytime I boot up, I get usb-uhci and ehci_hcd using IRQ 10 as well as my Digium card. Does anybody know what these are

Hi, thank you for last info. we've tried to use te110p but failed. We're quite surprised that cable wasn't included with the card as any documentation, at least on HW setup and installation, yet cable pinout for connection to PRI interfaces.... 1. We have followed instructions on your site and from Beronet guide, but card just keeps blinking and nothing happens (also no useful

Hi all, I am running asterisk 1.2.18, zaptel 1.2.18, libpri 1.2.4. on a suse 10.2, running kernel 2.6.18.2-34-default. The zaptel drivers are loaded on boot via /etc/init.d/zaptel, but Asterisk is unable to start. It ends with the following message: [chan_zap.so] => (Zapata Telephony w/PRI) Jun 13 13:05:41 VERBOSE[3356] logger.c: == Parsing '/etc/asterisk/zapata.conf': Found

Hi, I have problem using Asterisk.I have isdn-pri and openvox d110p card in my computer.They are connected with RJ-45 (1,2,4,5 pins to the card and all pins to the isdn done by telco workers). I got green led on isdn which is sign that isdn is working and that is connected to openvox, right ? I compiled newest versions of libpri zaptel and asterisk and had no problems during that. When I started

I go to my Zaptel 1.4.0 folder and run ./configure; make linux26; make install and I don't see any errors. This is out of my modprobe.conf: install tor2 /sbin/modprobe --ignore-install tor2 && /sbin/ztcfg install torisa /sbin/modprobe --ignore-install torisa && /sbin/ztcfg install wcusb /sbin/modprobe --ignore-install wcusb && /sbin/ztcfg install wcfxo