similar to: Problems setting up X100 FXO card

I am having a problem with Red Alarms on X100P cards. The most frustrating thing is I can not duplicate the alarms, therefore am not sure how to solve it. I have read after searching posts and the web that you can try different signaling methods which may help alleviate the problem. There is fxsks (Which I am currently using), fxsgs, and fxsls While reading the Digium site about these different

Hi, I using asterisk 1.2.4 on a CentOS with Linux 2.6.9-22.0.2.ELsmp kernel. I've two x100p cards connected, only one card is reconigzed by asterisk. 02:01.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface 02:02.0 Ethernet controller: Davicom Semiconductor, Inc. 21x4x DEC-Tulip compatible 10/100 Ethernet (rev 31) 02:03.0 Communication controller: Tiger Jet

I was studying the asterisk-users list archives to learn if anyone has had success with an X100P on a sparc. I noticed some postings on the subject. I am wondering if anyone has learned anything new? I have an Ultra-60 running Gentoo with 2.6.10 and udev. I built * 1.0.5 and have been enjoying various SIP configurations, with 2 sipura phones and 2 UIP200 phones (got them working!) in my home,

Hi again, I'm trying to setup our non pri T1 (they call it a Long Distance T1), our current pbx has the signaling set to E&M, I can set em in zapata.conf, but I'm trying to track down the proper entries for the zaptel.conf file. The digium docs only show a PRI example. Our current system has these settings: Signalling: E&M Framing mode: ESF Line Coding: B8SZ here's my

Does anyone know which signalling protocol works when connecting the output of a NT8B90AL Norstar ATA2 analog terminal adapter to an FXO card? (fxsks, fxsgs, fxsls?) I'm trying to add an Asterisk branch to my Norstar PBX as outlined at http://www.voip-info.org/wiki-Asterisk+Nortel. - Mike

Hi there, I have a cablemodem, ARRIS brand, model tm502G. It has two FXS ports. I was wondering if anyone has details about the correct signalling of these FXS ports when connected to original X100p. Tests: fxsks on the zapata.conf and zaptel.conf files. From my cellphone I call the ARRIS, it starts ringing but the zap channel sees no call coming in. fxsls on the zapata.conf and zaptel.conf

Hello, I am having problems configuring a TDM400P 4 Port FXO card with groundstart signalling. The box has 2 X100P's, 1 TDM04B and 1 TDM40B. I can configure it for loopstart and it works, just not groundstart, which I need for this installation. What am I missing? Thanks! Mark /etc/zaptel.conf #two X100P FXO Cards # fxsls=1-2 # TDM400P 4 Port FXO (TDM04B) fxsgs=3-6 # TDM400P 4 Port

Hi, i have installer wine from the Ubunu Dapper Repositories but i can't access the audio properties...when i run winecfg and click on audio, i come back to the console...its a problem with the alsa config, he cann't found a file... here is what i get : <CODE> ALSA lib seq_hw.c:456:(snd_seq_hw_open) open /dev/snd/seq failed: No such file or directory Creating link

I have a issue with two Zap clone cards where they used to work. I am using Asterisk@Home 2.5 which includes Asterisk 1.24 and Zaptel drivers 1.2.4. The system is a new Intel Celerion machine. I used to have the same cards running in a Intel PIII system. in this system, they worked. In this older system, I was able to call into the machine and call out from it. Now that I have upgraded

Hi All, I've got an MD3200 modem which is working as a Zaptel FXO interface for Asterisk (X100P clone I believe). It seems to work, but on incoming or outgoing calls I can hear the other party ok but when I speak, I hear my voice echo back at me (quite quietly but it's distracting!) on everything I say. The other party doesn't seem to hear the echo - they just say I sound a bit quiet.

Hi, I'm using zaptel-1.2.22.1 with asterisk-1.2.10 and following steps to make zaptel working... OS is gentoo linux 2006.1 Hardware: --------- 0000:05:01.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device 8085:0003 Flags: bus master, medium devsel, latency 32, IRQ 22 I/O ports at b400 Memory at ff900000

Em (20:59:21), Asterisk Users Mailing List - Non-Commercial Discussion escreveu: >On Tue, Jun 21, 2005 at 08:09:52PM -0300, Alessandro wrote: >> >> Does Somebody know why no load modules to FXS? I used zaptel-1.0.7 >> version. > >What color are the modules? >Post your /etc/zaptel.conf > >-- >Mike Mike, The color is green, red ans bluw. Link

Ok so I read the Linux 2.6 related README and finally compiled propperly, I thought but at the end I notice that lscpi does report the cards, but I cant modprobe wcfxo nor zaptel and I do have wcfxo.ko in the /lib/modules/2.6.8/extra/ directory, so what gives? This is a Debian Sarge, thanks! # # make clean starts here # make[1]: Entering directory `/usr/src/zaptel-1.4.0/menuselect' rm

Hi On an old IBM Netvista thinclient, the TDM card doesn't detect incoming calls, although the card seems to be detected, and correctly configured: pbx asterisk # lspci 00:03.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface # cat /etc/zaptel.conf fxsks=1 loadzone=fr defaultzone=fr # ztcfg -vv Zaptel Configuration ====================== Channel map: Channel

zaptel compiles fine (make linux26) but when I modprobe ztdummy I get the follow error. [root@localhost zaptel]# modprobe ztdummy Notice: Configuration file is /etc/zaptel.conf line 0: Unable to open master device '/dev/zap/ctl' 1 error(s) detected FATAL: Error running install command for ztdummy System info: Linux localhost.localdomain 2.6.9-5.0.5.ELsmp #1 SMP Thu May 19 19:24:44

asterisk-users-bounces@lists.digium.com wrote: > In the following setup: > call coming from a pstn line -> into FXO card -> asterisk -> SIP > phone > > i get an incredible loud echo in the SIP phone (about 0,5-1s) > (everything i speak into SIP phone microphone i hear in its > speaker). The person calling from PSTN is not getting any echo. Make sure you're not

Hi all, Does somebody know why no load modules to FXS? I used zaptel-1.0.7 version driver. [root@server1 zaptel-1.0.7]# modprobe wctdm ZT_CHANCONFIG failed on channel 3: Invalid argument (22) Did you forget that FXS interfaces are configured with FXO signalling and that FXO interfaces use FXS signalling? /lib/modules/2.4.21-27.EL/misc/wcfxs.o: post-install wcfxs failed

Hi All I have problem with LIBMFCR2 for once Exchange I using Sangoma card, the firstly. my ssystem run successful with MFCR2, connected to E10 (Acatel Exchange), after that, i move connection connect to EWSD (Siemens), my system don't work. error protocol R2. my system: Asterisk CVS 1.1.X LibMFCR2 pre.005 and unicall-pre.005 this's my setting and my setting wanpipe1.conf

Hi! > > > Since it is a PCIe card, it does not have the ability to host hardware > > > devices for networking, storage and console. We provide these devices > > > on X100 coprocessors thus enabling a self-bootable equivalent environment > > > for applications. A key benefit of our solution is that it leverages > > > the standard virtio framework for

On Wed, Jul 24, 2013 at 08:31:31PM -0700, Sudeep Dutt wrote: > An Intel MIC X100 device is a PCIe form factor add-in coprocessor > card based on the Intel Many Integrated Core (MIC) architecture > that runs a Linux OS. It is a PCIe endpoint in a platform and therefore > implements the three required standard address spaces i.e. configuration, > memory and I/O. The host OS loads a