similar to: Polycom Default .cfg

Hi, I just got and setup a new ip500 yesterday and it worked for about 15 minutes. Then it froze during a reboot.Now, when power cycled, the logo comes on for 3 seconds and then the screen is blank and nothing further happens. 468* factory reset doesn't work. I am about to send the phone back, but wonderd if anyone had a suggestion first.

While I'm asking about the Polycom ip500, the answers for all phones where mic/handset/headset levels are adjustable would be of interest to many I'm sure. For the ip500, the default value for the handset seems to be voice.gain.tx.analog.handset="3" I've noticed that echo all but goes away when one reduces the mic volume on almost any phone. My question is, for you users

Hello, I have configured my polycom ip600 and ip500. The phone works well. But the clock is wrong and flashes the whole time. Drives me nuts! I have set the time offset on the DHCP / boot server. 36000 (I'm in Australia!) It doesn't seem to help... Mike

Hi, I just got my ip500 back after months of waiting. Is there an easy way to get it hooked up to asterisk without [t]ftp servers and all that or is there a quickstart page somewhere? tia r

Hello, I am looking at the Polycom phones. The ip600 has a very nice screen, is that the only real advantage over the ip500 and ip300.. Is it worth the extra dollars? Kind regards Michael Felder IT Medic Australia Pty. Ltd. P: 03 9557 2213 F: 03 9557 2214 M: 0419 568 217 E: Michael@ITMedic.com.au <blocked::mailto:Michael@ITMedic.com.au> http://www.ITMedic.com.au

I've had an IP300 for a while now and it's been working fine. I just got an IP500 and when it connects to the FTP server it downloads the new bootrom and says error loading. The bootrom is fine and works on the 300... In addition, I downloaded a new copy to be sure and it still doesn't work. Can anyone give me some advice?

I'm guessing that I need more info entered into the 'message centre' section. What did you key in? Paul Hales IT Support Adairs -----Original Message----- From: Jeff Pyle [mailto:jpyle490@gmail.com] Sent: Friday, 17 September 2004 11:27 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Polycom IP500 I have two IP 500's on my Asterisk

What gives with the stupid stupid power system on the Polycom IP500 (I hope they changed it on the 501's). Anyway, does anyone know if you can get some type of joiner to connect two Cat5 cables together, and will this affect the call/signal quality because my Ethernet cable is longer than the dumb 11ft polycom supply (oh and their manual is the wrong about which end goes into the handset

Hi I am struggling with hardware choices to get started with. My options are narrowed down to SIP phones - Polycom IP500, IP600 and Cisco 7940G. of importance is: - functionality / integration with asterisk - headset functionality and use - voice quality - build quality Is there much of a difference between Polycom and Cisco? Scanning the group it looks like there may be slightly more

Hi Everyone, I've been asked to determine which phones our organization should go with. And I've narrowed it down to the Polycom IP500 or the Cisco 7940. From my travels through google, it's hard to find a definitive comparison of the two phones. So I thought I would ask the people that have probably used both. From what I can tell, the only major benefit the Cisco has over the

Hi All - I'm running version SIP version 1.3.4 on various IP300, IP500, and IP600 Polycom phones. I'm having a tough time with MWI. I thought I remembered somebody on the list saying that they had it working, but I can't find it in the archives now. I have all the phones configured for MWI as specified in the WIKI: ipdmid.cfg: up.oneTouchVoiceMail="1"

I am trying to use a Polycom Soundpoint IP400 with my asterisk setup, and have been unable to find the proper firmware and application files to make it work. The phone can access the FTP server, and downloads the IP500/600 configuration files, but claims that the sip.ld file is larger than its file system. I can think of two possible ways to make this work. One is to find the IP400

Hey all, I'll give my reseller a call for support in the morning, but I usually have better/faster luck on the list. I've got a SoundPoint IP500 that I upgraded to BootROM 2.6.2 and SIP image 1.5.2 on someone elses advice, I forgot to change out the old config for the new when I loaded the image up (I guess the config changed a bunch between 1.5.2 and 1.3.1) I was prompted with an error

Anyone else have problems with soft buttons not being responsive at all? 2 of the 4 soft buttons do not respond, no matter how hard you push. It is an IP500. Well over 1 year old. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20061208/b3fa0b42/attachment.htm

Hi All, I am a remote office that is connected to my office via openvpn on UDP. Voip has always worked well (after discovering g729). Initially I used a softphone, then an analog set on a sipura 2000, then a polycom IP500 (I still LOVE this phone). At that point, I started noticing that the polycom doesn't ring a lot of the time. Since I was desperate for a phone, I didn't upgrade

Hi, Has anyone used polycom phone IP500/600's conference feature? I ran into some issues. Polycom is not behind NAT. Polycom calls pstn number A, (gets two way voice), presses conference, (A is put on hold), calls pstn number B, (gets two way voice), presses conference again, suppose to have all three parties in the call, polycom and B have two way voice, but polycom doesn't have two

Hi, I have lookedaround and don't see this anywhere. Is there a way to tell the ip500 to not make the aural MWI blips?

Hello all, Has anyone used the SIP version of this phone with Asterisk? I see Polycom has a H.323 and MGCP version also, does anyone know if you flash the phone to swith protocols? Thanks in advance for the info. Ed -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20031029/a9377305/attachment.htm

I have sent a Polycom IP500 phone to an overseas remote user who has a Speedtouch adsl modem/router. The phone is connected to the 4 port router which performs NAT for the network. The phone rboots, find the server, downloads it's config and tried to register. Then it immediately becomes UNREACHABLE. Jul 26 17:44:41 NOTICE[21026]: chan_sip.c:9138 handle_request_register: Registration from

> Hmmm... I have this aweful feeling that I'm choosing the > exact wrong time to ask a "newbie question" :) Oh well, here > it goes. > > The quick question is : "How do I dial an extension?" > (answer is probably - "you don't" in which case:) "How do I > dial my asterisk box?" - I have no outside line, I just want >