similar to: TE110P problem

Anyone have any luck with connecting Asterisk to the Panasonic KX-TD500. I have Asterisk connected via crossover to the TE110P. We are able to make internal calls into the Asterisk Box but the PBX vendor (I know nothing about the KX-TD500) tells us it is not possible route DID over the trunk. I find this hard to believe. Anyone have any luck with this? Thanks! -------------- next part

Ok I F@%& up. I didn't realize the card is 3.3 volts and my new computer is 5V. Can anyone point me to a PCI to PCI bridge. Any suggestions? Mike

Has anyone had any compatibility issues with a TE110P card installed on a Dell Poweredge 1950? I noted the following error on the LCD display of the Dell Poweredge 1950: E1711 PCI PErr Slot 1 E171F PCIE Fatal Error B0 D4 F0. The Dell hardware owners manual states that it means the system BIOS has reported a PCI parity error on a component that resides in PCI configuration space at bus 0,

Ok all here is a strange one...... I have a TDM400P with 3 fxo modules. I can very rarely make an outbound call to the PSTN....about once every 10 tries. However if I use a analog phone pluged into the same phone line as one of the tdm channels say channel 4, and I place the analog phone off hook and then place a call via asterisk , it work everytime. It seems like the TDM400p is having

Dear All, I'm having problem with spandsp/txfax, I'm not able to send a multi paged tiff file, the fax machine receives the first page of the document and complains about communication problem. The file what I'm trying to send has 2 pages and is received & generated by spandsp/rxfax. Searched in the archives, but found no solution. I'm using: Dell Optiplex PC Inoteska Quad

Does anyone know if you can have multiple TE110P cards in one chassis? -Thermal -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20061011/adbceeb5/attachment.htm

Hello Everyone, I checked with zttool that sometimes after the machine boots the order of the boards is changed like this: ??? Alarms Span ??? OK Digium Wildcard TE110P T1/E1 Card 0 ??? OK Digium Wildcard TE110P

Hi! I'm trying to setup a Wildcard TE110P with a PRI in The Netherlands. I get a Red Alarm on the line. Is there any way of debugging this? I've tried some configs that should work but without success. Is there any way of telling if the cabling is correct or what else the problem could be? Thanks!! Remco

Hello, All. I have a problem with receiving fax through T.30. I'm calling 543 number from fax machine, then start sending fax and fax machine send document without problem. But asterisk don't receive fax. I can't find good documentation for app_fax and I'am googled this errors. Please help me. software: asterisk-1.6.2 OS: ALT Linux 5.0.1 Ark Server hardware: Digium Wildcard

I have an Asterisk server that was running fine until Sunday. Monday there was a power outage and the server was off most of the day. This server has a TE110P, two TDM04B and an Astribank 32. Today I noticed that the TE110P started having IRQ missess. Before today it only had about two or three per month. Today, this is the miss count after ten minutes on: IRQ Misses: 1443

please can someone send to me his files like zaptel & zapta if he si using TE110P thank you

I have a Digicom TE110p card installed in our exchange. I have compiled and installed libpri, zaptel and recompiled and installed asterisk. I have configured udev as I am running Fedora Core 3. The problem that I have is that when zaptel is not running everything works fine. However when I start zaptel (service start zaptel) then I can make normal calls ok but the 'Playback()'

Hi, thank you for last info. we've tried to use te110p but failed. We're quite surprised that cable wasn't included with the card as any documentation, at least on HW setup and installation, yet cable pinout for connection to PRI interfaces.... 1. We have followed instructions on your site and from Beronet guide, but card just keeps blinking and nothing happens (also no useful

Good day all We got a Wildcard TE110P I installed linux,zaptel,libpti and asterisk I coped over my zaptel.conf and zapata.conf from a previous E100P config But when I try to start asterisk it gives error not bying able to load zap channles: == Parsing '/etc/asterisk/zapata.conf': Found Jan 10 08:17:18 WARNING[-1084595552]: chan_zap.c:9308 setup_zap: Ignoring switchtype Jan 10 08:17:18

Hi All, I have configure my Asterisk as follow (using Asterisk@home): [zaptel.conf] span=1,1,0,ccs,hdb3,yellow bchan=1-15,17-31 dchan=16 loadzone = uk defaultzone=uk [zapata.conf] [channels] switchtype=euroisdn pridialplan=local prilocaldialplan=local internationalprefix=00 nationalprefix=0 usecallingpres=yes busydetect=no ; not need on pri callprogress=no ; was yes but wiki says experimatley

Hi everybody, i need someone to tell me the spins numbers of Rx+,Rx-,Tx+ and Tx- of TE110P and also if you can tell me have to made a cable like that?? Modem Teleco <-----------Self Crosscable------------>Asterisk Rx+ <--------------------------------------------------------------> Tx+ Rx- <--------------------------------------------------------------> Tx- Tx+

Hello all, Has anyone use the Supermicro PDSME+ in combination with the TE110P successfully? My experience so far is not very good. I am running trixbox 2.0 but: 1) with zttool I am getting IRQ Misses. Don't seem to have IRQ conflict, but I am now running my SATA HD in DMA. And I am not able to set it in DMA(HIO... operation not permitted) 2) With zttool the Alarm is RED 3) When I do the

Hi folks, I've already searched the mailing list but no one else seems to have my same problem. I'm using Asterisk with the following configuration: Fedora Core 4 (but I also tried Fedora 3) 1 Digium TE110P 1 TDM40B 1 HFC-S 'Cologne' bristuff 0.2.0-RC8o (zaptel 1.0.9.2) I compiled right, I can load kernel modules but when I try to unload wcte11xp module (the one

Running Asterisk 1.2.9. I just installed a TE110P card and configured zaptel.conf & zapata.conf. The config files look right to me but I'm getting the following error when trying to start asterisk: Asterisk died with code 1. Automatically restarting Asterisk. Does anyone have any idea what is wrong with this configuration?? Thanks in advance!!! Here's my config files: zaptel.conf

Hi list, I have a terrible noise issue with Dell SC1430 + Digium TE110P. The digium card is not sharing interrupts with any other device, as I saw in Dell's BIOS and also with "lspci -vb" command. After changing coax wire, UTP, balum, digium card ... I have found that the problem is in Dell box, so now I'm running the same Asterisk config in other server with the same