similar to: adding another fxo card

The card you installed has FXO or FXS modules in it ????? are you getting your lines directly from the telco co??? Doug D On Mon 23/08/10 8:37 AM , Cassius Smith cassius at cassius.org sent: * -----Original Message----- * From: Todd Reese * Reply-to: Asterisk Users Mailing List - Non-Commercial Discussion * To: asterisk-users at lists.digium.com [3] * Subject: [asterisk-users] Dahdi

I have an eight channel fxo setup (2 TDM400P cards) and I have them setup. Here are my configs: Zaptel.conf: fxsks=1-8 loadzone=us defaultzone=us Zapata.conf: [trunkgroups] [channels] musiconhold=default rxwink=300 ; Atlas seems to use long (250ms) winks usecallerid=yes hidecallerid=no callerid=xxxxxx callwaiting=yes busydetect=no callprogress=no usecallingpres=yes callwaitingcallerid=yes

Hello, I've one astribank with 8 FXO unit and 8 pstn lines connected to the astribank. When I receive calls on my ipphone I get always Unknown callerid. It's is possible to receive the callerid from the lines on the astribank unit? This is my config: [channels] language=es context=from-zaptel signalling=fxs_ks ;rxwink=300 usecallerid=yes callerid=asreceived ;cidsignalling=bell

Hello. New to the list. We're in the process of deploying Asterisk. Actually, we're going live tomorrow, and I just found out that my Zaptel cards have been mis-configured. I'll preface this by saying that I have looked in the wiki, read through the samples, and attempted to call Digium (they're closed.) So I'm praying that someone on the list can help me out! I have two

Hi, I know it sounds weird, and this is part of the reason I have not reported that sooner. As I upgraded from 1.6.2.x to 1.8.x several months ago I am experiencing this problem. If a call is initiated from a DAHDI extension after no DAHDI extensions were used for some time, arbitrary DTMF digits are skipped and the call fails. If the call is redialed it goes through. Normally just one (1)

I'm a bit confused on how to setup Zaptel.conf and Zapata.conf when there is a TDM400P and a TE410P installed after upgrade. The TDM400P has 2 FXS in position 1 & 2 and 1 FXO in the fourth position. I see boot, WCT4xxP loading first and WCFXS loading second. According to my understanding, given above, the TE410P should be configured first, then the TDM400P. However, I'm not sure

Hello, I have some problem to start asterisk. First I have followed a lot of tutorials to complete correctly the install process. Now it works when I type zttool I can see when I am or not connected to the PSTN. But, I run asterisk with vvvv verbose and I can't see the call detection. There is no detection of the call. I have a X100P card FXO with only one line. So only one channel I

The TDM01B is 4 port capable but has only 1 FXO module. I'm running asterisk 1.2.7 and zaptel 1.2.5. I cannot seem to get the TDM01B working. When I do the zttool it shows 4/1/0. I can dial out from a POTS phone up to the point that the cable plugs into the card. Here is my /etc/zaptel.conf loadzone=us fxsks=1 and here is my /etc/Zapata.conf [channels] language=en #include

hi you, I'm having problem with voice quality on my trixbox using TDM2400B.The trixbox is connected via 20 FXO ports on a TDM2400 with the hardware echo cancel module. Echo cancel almost works, but the users hear what they describe as a 'background crackle/buzz' coming back when they talk. anyone have the same problem? pls help me. thanks a lot. my trixbox and config

I have an Asterisk@Home 1.3 server (Asterisk 1.0.9) and recently added a TDM400P with (1) FXO card on port 4. Inbound calls are always successful but outbound calls fail 75% of the time with intercept messages from my dial tone provider that include "we're sorry, your call did not go through", and "we're sorry, when placing a local call it is now necessary to dial an area

Details: Asterisk 1.0.9 Zaptel 1.0 Dell P3 1ghz with X100P Clone Location: India This is an interesting issue where when I open up ZTMonitor, it shows the RX as being on. It seems that Zaptel doesn't know to hang up the line so after a couple of hours when the telecom cuts the line, everythign stops working. Things I've tried include playing with the zaptel.conf, trying zaptel v1.2(with

So I have an application where the users want to divert incoming calls on one analogue line out to another analogue line - both lines are supplied by BT and theres a TDM400 in the box. Call comes in, system Dial's the forwarding number and bridges the calls. Works fine. Until one (or both) leg hangs up. And the box never sees the hangup. So it sits there with both Zap channels open

Hello, I have another little problem with my ZAPs channels, in fact, when I received a call, I heard no sound while in the CLI, sound is played: -- Starting simple switch on 'Zap/4-1' -- Executing [s at from-zaptel:1] Answer("Zap/4-1", "") in new stack -- Executing [s at from-zaptel:2] BackGround("Zap/4-1", "hello-world") in new stack --

Hey everyone ! I have a problem in making outbound calls in PRI connection. I have E1 PRI airtel connection [ India ] [ asterisk-1.2.12.1 on CentOS 4.4 ] zaptel.conf ---------- [channels] language=en usecallerid = yes hidecallerid = no callwaiting=yes threewaycalling = yes usecallingpres=yes transfer = yes echocancel = yes echotraining = yes immediate = no ;group=0 ;context = from-pstn

Hi all, I have TDM2406E with 24FXO ports connecting to 10 POTS line sitting in my office. the out going calls symptom like when called party pickup the phone but the calling party still hearing the ring tone from the IP phone. Please light me up. it been many sleepless night by googling around trying to get the right answers. The digium card running on Intel 915G chipset. Below are my zaptel

Hey all, I'm having problems where there is significant static when making SIP -> PSTN calls. SIP -> SIP and SIP -> VM calls are totally clear and fine. Here's the setup: Polycom 601,501, and ten 301s. Digum 2400 TDM card w/echo cancelling, 12 FXO ports. The TDM card is on IRQ 5 with nothing else on it. Server Specs: Asus P4P800E Deluxe P4 3.0 Ghz 1 GB Ram 80 GB SATA HD -

I am just starting out with * so bear with me please. I have tdm400p with 4 fxo modules on it. When I call into the asterisk box from my mobile, I can see the asterisk console picks the call up and routes it to my computer with x-lite. There was no sound coming from either - just silence. I then decided to route it directly to voice mail to see if that would narrow the problem down, but it

I installed Trixbox and a TDM400P with 2 FXO and 2 FXS ports and am having an annoying issue with the FXO ports. As soon as I plug either one into the phone line it's as though the line is disconnected i.e. get disconnected tone when trying to dial out, line is busy when dialling in. The CLI shows the following: trixbox1*CLI> zap show channel 4 Channel: 4 File Descriptor: 18 Span: 11*

Good Day list, I have worn out my google toolbar today looking for a way to determine which group an incoming call belong to, but have not been very fruitfull in my endeavors. I am trying to figure a way to determine which group the incoming call that I just answered is part of so I can do some branchinbg scripts in my dialplan. I know I can control my dialplan logic by creating separate

Hi, I'm installing an Asterisk box with a TDM2400P in Brazil. I can make analog phones work while lines are not working. Since I do not know anything about brazilian lines, is there anybody who can tell me what is wrong/missing in my conf files (below)? TIA Giorgio _zaptel.conf:_ fxoks=9-16 fxsks=17-24 defaultzone=br loadzone=br* * _zapata.conf:_ context = inbound_zap echocancel = 128