similar to: TDM40B and weird analog problem

All, I have AAH 1.0 installed using Digium TDM04B and Grandstream GXP2000 phones. All seems well other than the phones have to be reset up to 5 times per day. It is like they lose thier ip connection or maybe thier SIP connection. Has anyone else experienced this issue? I have the phones set for static IP addresses and that doesnt seem to help either. Any help would be greatly

OK, here's the setup, AAH 0.8, Grandview 2000 phone, Digium TDM04B interface to POTS lines. Everything seems to be working just fine, but I have some questions on how to access voicemail options. I can leave a message for an extension, but when I try to retrieve it by using *97 it asks for the password and even though I type in the same password I gave the extension for vmail, it tells

Hi, I had ordered a TDM40B and developers kit a few months ago. I have everything installed and working, with one exception - sound quality. When placing a call it sounds like a very bad cordless phone - lots of hiss / static in the background. This even happens with the dialtone, though it is much worse one the call is connected. This does not occur when the phone is directly connected to the

Hi, I'm no phone guy but I've been having quite a bit of fun messing with Asterisk. I just unwrapped my new Wildcard TDM400P (TDM40B) which is the new 4 port FXS PCI card. It has 4 RJ45 connectors and I'd like to hookup 4 regular phones which are RJ11. If I crip RJ45 connectors to the phone cords do I simple use the center two pins (pins 4 and 5)? Thanks, Randy Smith Tiger

Hi list, I'm trying to set up a TDM40B, but modprobe returns the fowling errors: asterisk:~# modprobe wcfxs ZT_CHANCONFIG failed on channel 1: Invalid argument (22) /lib/modules/2.4.18/misc/wcfxs.o: post-install wcfxs failed /lib/modules/2.4.18/misc/wcfxs.o: insmod wcfxs failed Could someone give me a help? Thanks in advance Eduardo

After purchasing the Uniden TRU9480 and then the Panansonic 5672, both of which do not have "phone company" compatible FSK/stutter MWI, I finally got smart and found out just which Panasonic phones have this feature. Only the following 5.8G models in their current line have FXO compatible MWI. I purchased the 5771 unit and one remote. I have confimed it does in fact work with Asterisk

Hello I have an office with a T1 that provides 4 (out of 8) analog PSTN lines thru an adtran board. I want to add 4 more analog lines. Currently I have a Digium TDM40B. I'm wondering what the best upgrade path is, where I define 'best' as the solution that is most likely to work without problems (like interupt conflicts) and work with my current echo tuning . I see my purchase

OK, now this should be really simple, but I am a bit of a newbie so please bear with me. I have an *@Home box setup with TDM04B and two POTS lines. On the SIP side, I have GXP2000 phones. Most things seem to work, but the users cannot figure out how to transfer incoming calls from one extension to another. Now I am not sure that I have things setup correctly, but is there something

Hi all, Does anyone run Asterisk on FC4? with Digium's TDM40B cards. any success stories? my Intel 865 M'd+ Intel 3.0GHz freezee during installation (FC4). Please any comments? Kumara

Hi! I have a Grandstream VoIP Device, at which a DECT base with 2 cordless phones are connected. If a call is placed and made through one cordless phone the other cordless phone appears as busy. What I want: 1. The Base station of the DECT cordless phones, is connected at 1 FXS Port of my Grandstream Telephone Adapter. 2. I want to place and receive as many calls at the same time through 1 SIP

This is rather bizarre: My TDM11 (one FXS) rings a $10 passive phone with REN of 1.0B, a cheap speaker phone of 0.3B, and a cordless phone with marked REN of 0.0B. But it couldn't properly ring this 27935GE3-B (FCC ID G9H2-7930) cordless phone rated at merely 0.1B. Rarely, the phone will crack out an occasional weak and abrupt beap, but never a normal ring. Otherwise Asterisk and TDM400P

I have problem with a TDM40B installation. When i modprobe wcfxs the error i get is the following: /lib/modules/2.4.19-4GB/misc/wcfxs.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg /lib/modules/2.4.19-4GB/misc/wcfxs.o: insmod

Afternoon all, After doing some test on my asterisk box I can successfully receive calls to my Asterisk PBX to a SIP phone from The Telstra PSTN network Dial out from a sip phone is also not an issue, all calls connect and terminate normally. If I call the Asterisk PBX say from PSTN in Zap1-1 and out through ZAP2-2 back to the PSTN (after entering the correct pin off course) the card does not

I'm having trouble with a WX100USB adapter and a Siemens Gigaset cordless phone. If I select fxols as a signalling method, calls are being disconnected. Usually after about 4 minutes, and asterisk just says that the phone has hung up. If I choose fxogs, I immediately get a LINE IN USE message on my phone and I can't even get a dialtone. If I choose fxoks, it mostly works, but sometimes

Can anyone recommend a good cordless user-configurable SIP hardphone that is readily available in the states and doesn't cost $300? There seem to be a plethora of decent and affordable corded phones (like from Grandstream) but the search for a cordless unit seems elusive. I purchased a vtech 8100 online only to discover after receiving it that it is locked to vonage service. Thank you.

What is involved in provisioning Asterisk to use a multiline analog service from our local telco? I will only have one twisted pair entering in on a OpenVox card but am not sure how Asterisk interprets and deals with two incoming calls and/or two outgoing calls? Thanks! jlc

does anyone know of a 2.4 or 5 ghz cordless phone system that has an ip base station? thanks

Hello! Attached to the bottom of this e-mail is an edited version of an e-mail I originally wrote to Digium tech support regarding Ouch and Power alarm errors I have been receiving on my TDM400. It contains a great deal of detail regarding my setup. In the end, I have found that one of the 5 phones I'm trying to make work with Asterisk is contributing to the generation of these errors.

I'm looking to build a VoIP solution for 100+ service vehicles that have WiFi hot spots installed (with cellular uplinks). Currently we are trying out Skype wireless handselts and Majick Jack. I'd also like to consider an Open Source solution that can bring the calls back to our data center [possibly integrated without our existing BCM 3.x VoIP PBX]. For hardware someone on the IRC

In that example you could make outgoing calls only correct? (since incoming likely needs port forwards) I guess the questions becomes "how often are you going to do that to justify the extra $100 or so you going to pay for a wifi sip phone?" Paul Fielding (paul.fielding@shaw.ca) wrote: > > I think some people are missing the point. You can't throw your cordless >