similar to: Control IAXy Provisioning from a central

For anyone playing around with IAXy(S100i) devices, I am making the following available: Windows IAXy Provision v1.00 This is a from-the-ground-up development of a means of provisioning IAXy devices using a Windows environment. For some users, being bound to Linux for IAXy provisioning is not viable or convenient in some cases. This application provides a GUI data entry for the various IAXy

Hi. I am trying to provision my newly purchased IAXy. I tried ./iaxyprov 192.168.0.4 myiaxy.conf It print a bunch of numbers on screen and then say Provisioning is 63 bytes Total packet is 77 bytes Got response back from '192.168..0.4' And that's it. I didnt get nothing else and there isnt any solid yellow light after minutes. I wonder if anyone could explain what I'm seeing? Is

I've heard comments about the instability of the IAXy (loosing IP, locking up, etc) . I want to deploy some, in a remote site. The comments on the instability suggest that the simplest approach is to power-cycle them when you have problems. The IAXy would only be in use from 3PM to 8 PM. My potential simple solution is to have a timed power brick (like what you would use for a block heater)

Hello. I picked up a couple of IAXy's for testing. Unfortunately, I read the negative comments only after I bought 'em :( Regardless, I provisioned one unit using my local Linux computer. Now, I'm trying to set it up to provision using the remote * server whenever it tries to register, but it seems I need to know the "service identifier" for the specific device. I can't

Hi, I've got an IAXy, and provided it with connection data - unfortunately didn't provide a fixed ip address, but left with dhcp. Everthing went fine, and I could work a while with it. After a restart of IAXy, it didn't negotiate a new IP address, nor used the old one. I even restarted the DHCP server and cleared its cache. No success. I went to another office with a different

Greetings all- Long story short - I find myself suddenly running a Asterisk PBX after old PBX suddenly died. Fortunately, I had been "playing" with Asterisk (via Trixbox) on a server in consideration of replacing our aged Merlin Legend - so over the course of last weekend, I brought my testbed PBX up to full operation and now supports about 30 users. All in all, went smoother than

Hi all, getting a server going wiht a few TDM400's and some phones, and some IAXys too I haven't heard any issues about AU phones being able to RING in Australia, like the problem in the UK with ring capacitors on the BT system. Are there any problems like that? Also, with the iaxy's -- they should work (and ring) in Australia right? The only hint I'm seeing around is the use

There is no DNS functionality built into the IAXY, I am assuming you want to be able to home onto a SOHO site with a dynamic IPaddress. I have not been able to figure out a clean way to do theis (make it easy for the roaming sales-folk etc,) who will not have a high tolerance for running something like an IAXYPROV. You would need to somehow have an external fixed address which would

Hi, hoping that experienced hands will quickly show me the right way: after a fruitless web search i am turning to this list with my rather elementary question: is there any other way to communicate with the IAXy besides using special utility software that needs to be compiled under UNIX? Here is the story: about two months ago, after some not very satisfactory attempts at using SIP (my phone

Ok, I searched the lists and found no definitive answer. I'm assuming the IAXy has some primitive form of echo cancel, is there anyway to adjust this? Or any ideas on what to do instead. Here's the setup, this will not be a typical setup for our company however, well whatever. Anyway it looks like this: IAXy --> Netgear router --> Charter --> Level3 --> Asterisk --> VOIP or

I have a brand new IAXy I'm playing with. I do not get a dialtone on the phone, or any response at ll on the phone. No sound, no dialing, no ringing. The phone and wire are tested and known to be good. I think I have it setup correctly. When I give the iaxprov command I get this: #iaxyprov 192.168.1.90 iaxy.conf 02: c0 a8 01 5a 05: 11 d9 03: ff ff ff 00 04:

I place a call from an IAXY to an IAXY device. INitially the calls show in the output of "show channels". Then after a few seconds the "show channels" command shows 0 active channels even though I am still talking on the channels. Any ideas on this? THanks, Jerry

Hi all, I have a small query regarding ringing tones on an iaxy2. I have a customer who uses an iaxy to breakout to pstn via our *. However the customer complains that he gets no ringing tone whislt making calls, i just visited the site and can confirm this. I also have another customer who is presently in canada with an iaxy calling thru our * , he doesnt have this issue. I presume that the

Hi All; I need to buy one IAXy device, but I discovered that it supports only g711 and ADPCM codec, so I was wonder that it does not support g729 or GSM?! Anyway, what is that ADPCM and how much it consumes bandwitdh? Also, asterisk support such codec? What its name in the configuration? Any advise? Regards Bilal

The file used with a Digium IAXy device: "iax.conf" has the line: "port=5036" (I also use the "bindaddr=192.168.1.91" entry) but when Asterisk talks to the IAXy device it used port 4569 (from "tcpdump"). How are the port numbers assigned? What tells the IAXy which port to use. The IAXy provisioning file "iaxy.conf" file does not specify a port

The file used with a Digium IAXy device: "iax.conf" has the line: "port=5036" (I also use the "bindaddr=192.168.1.91" entry) but when Asterisk talks to the IAXy device it used port 4569 (from "tcpdump"). How are the port numbers assigned? What tells the IAXy which port to use. The IAXy provisioning file "iaxy.conf" file does not specify a port

Hey Everyone, I recently purchased a few IAXy units for some testing, and have come across a some problems. One of them can be provisioned but will not ring the connected telephone. It also does not provide a dial tone when you pick up the phone. When a call is made to the IAXy one of the green lights on the board goes from a solid on state, to a flashing state that coincides with the

Not sure if this is the best place but does any one have any used IAXy's they are interested in selling? I am looking to pick one up cheap for a proof of concept before going all out on them. Also does any one have any real life practical experience with how well (or not so well) that these devices have worked for them? you can reply to me off list at asterisk@matraex.com Thanks Michael

I have been searching for a while and can't find anything specific like this. Here's is my setup: IAXy -- broadband network -- Asterisk -- TE110P -- Channel Bank -- POTS lines (FXO) Everything works fine except for the echo at the IAXy. There is no echo on the POTS end, so Asterisk is doing a good job of echo canceling. Is there any provisioning in the IAXy to do echo

I have a couple Iaxy's and when calling out on them I dont hear ringing. Everything else is working fine. Any ideas? THanks, Jerry