similar to: Question about the latest CVS and Zaptel

Hi, I'm wondering why zttest shows Best: 99.976 -- Worst: 99.967 -- Average: 99.971469, Difference: 99.971469 Shouldn't it be 100% as timing is hardware and comes from PRI? Am I missing some kernel config? Regards, Atis My /etc/zaptel.conf is span=1,4,0,esf,b8zs span=2,3,0,esf,b8zs span=3,2,0,esf,b8zs span=4,1,0,esf,b8zs #lspci 07:03.0 Communication controller: Digium, Inc. Wildcard

Hello, I'm running * on a very basic configuration. I have a Wildcard TE405P with the first T1 connected to a PRI line and the remaining three to Adtran TA750 channel banks with FXS modules. I successfully configured everything to work with a couple of Swissvoice IP10S handsets (MGCP) and analog extensions connected to the channel banks. The problem I'm having is that when I pick up any

Hi I got the 2nd Gen firmware upgraded on the TE405P. I recompiled after putting in the upgraded board but did not change any conf, but the spans become active but will not come up. I guess I am missing something or are the any changes to the zaptel/libpri software that is required. I cannot find any info about this or does this new firmware only work with latest CVS. I am using 1.0.9 with

I'm installing TE405P card. This is my zaptel.conf. -------------------------------------- span=1,0,0,ccs,hdb3,crc4 span=2,1,0,ccs,hdb3,crc4 span=3,0,0,ccs,hdb3,crc4 span=4,0,0,ccs,hdb3,crc4 loadzone = us defaultzone= us -------------------------------------- When i modprobe wct4xxp, -------------------------------------- PCI: Found IRQ 11 for device 02:0b.0 PCI: Sharing IRQ 11 with

I successfully installed asterisk@home 0.6, but when i try to load the wct4xxp module for the TE405P I just got, I get the following: Found TE410P at base address fb7ffc00, remapped to e0220c00 TE410P version c01a009b Tried to load 1c8ac800 into 00000000, but got 188ac800 instead Tried to load 1c8ac000 into 00000001, but got 188ac000 instead Tried to load 07fc07fc into 00000002, but got 03fc07fc

Dear All I installed a Digium card TE405P with zaptel and its running successfully with no alarms, but asterisk is not running . Any one have a cure or advice 03:09.0 Communication controller: Digium, Inc. Wildcard TE405P quad-span T1/E1/J1 card 5.0V (rev 02) Nov 14 07:56:58 localhost kernel: wct4xxp: Clearing yellow alarm on span 2 Nov 14 07:56:58 localhost kernel: wct4xxp: Clearing

Hi, I am new with asterisk. I am setting a Wildcard TE405P. E1s in Italy come in on a pair of RG-59 coax cables with BNC connectors. So I need an adapter/balun http://www.allcomtlc.com/al_g703n3.htm . I have It but I am not sure that It works. I have configured my asterisk in this way: zaptel.conf span=1,1,0,ccs,hdb3,crc4 dchan=16 bchan=1-15,17-31 loadzone=it defaultzone=it zapata.conf

Last tuesday I moved the asterisk server from 1.0.7 to 1.0.9, while leaving the zaptel drivers at 1.0.7 because it was a "lunchtime" update. This is a box with two TE405Ps in it, and all eight ports in use. Today I unloaded the 1.0.7 drivers and replaced them with 1.0.9 and oh boy... two of the 8 PRIs didn't want to come back, I got a million of FCS errors over the console and I got

Hello. New to the list. We're in the process of deploying Asterisk. Actually, we're going live tomorrow, and I just found out that my Zaptel cards have been mis-configured. I'll preface this by saying that I have looked in the wiki, read through the samples, and attempted to call Digium (they're closed.) So I'm praying that someone on the list can help me out! I have two

Hi, I got some errors about not being able to create subdir [already existing] on a 'make update' in my zaptel 1.4. I removed the directory and did a new svn co of zaptel 1.4 [ svn co http://svn.digium.com/svn/zaptel/branches/1.4 zaptel ] now I get: .... /usr/bin/install -c -D -m 644 tonezone.h /usr/include/zaptel/tonezone.h make -C firmware hotplug-install DESTDIR=

I just upgraded my asterisk install from january 2005 CVS HEAD to current CVS HEAD : * zaptel * libpri * asterisk My asterisk have one TE405P with one span (the clock source) pluged into a telco PRI E1, a second span is a PRI E1 to another PBX and the third one is a T1 to a rhino channel bank. Everything went smoothly except that the two PRI span restart every ten seconds after some HDLC

I tried to upgrade to 1.0.5 for libpri and all asterisk stuff to the last version. But now, my spans stays in RED Alarm. All seems ok, no error. Just no more links up I use a TE405P. Any idea ? I think it?s something from the old release that make conflict. So I tried to get back to previous version but I got the same problem. Not more SPAN UP Is there a script or something to

Hi, I'm confused as anything by this bug. I'm hoping that it is just something screwy in my config. I have 1 Cisco 7960 and several Grandstream BT101 & 102's, and a Digium TDM31B. I'm running the latest CVS (CVS-HEAD-05/27/04-17:22:40) of both Asterisk and the Zaptel driver on Fedora Cora 1. When I make an outgoing call on the Cisco phone, everything works fine. I'm

Hi I'm buying a new box and it brings the new PCI-e standard and not the old PCI slots. I would like to know if the Digium Wildcard TDM400P and <http://www.digium.com/index.php?menu=wildcard_tdm400p2>Wildcard TE405P will work with this PCI Express. <http://www.digium.com/index.php?menu=wildcard_te405p> Has anybody worked with PCI-e yet? As far as i understand, the Wildcard

Is anyone interested in the RPMs I have built for Mandrake 10 (kernel 2.6) of a recent CVS dump? I have source RPMs for zaptel and asterisk which should work with any 2.6 kernel version of Mandrake (including Cooker). I haven't done anything with PRI so that isn't built. I also have binaries available for kernel 2.6.3-15mdk. I have deployed these RPM's in a small number of locations

Hi, I recently installed an Asterisk server at a customer's here in Germany, using a Wildcard TE405P - Ports 1 and 2 (group 1) are connected to the phone system (Deutsche Telekom), whereas ports 3 and 4 (group 2) connect to the existing HiPath 3500 PABX. Currently, the dialplan is doing nothing but routing calls through (bridging) for the time being: -- [inbound] exten =>

Hi, I've been avoiding investigating this issue for a while; I used to revert to a previously compiled version of zaptel & a previous kernel (as at some point I think I stopped being able to compile the older zaptel against the newer kernels) and all was well. However I've now upgraded kernels again and it seems silly to hide from the problem - here goes, let's try and fix it! At

We are using AAH with Asterisk 1.2.7.1 with a TE405P as listed below. We are getting frequent restarts on the spans which lead to dropped calls. I have pasted some hopefully pertinent information below -- anyone have any clues that might help? Thanks Next line is repeated throughout messages, going through every channel in every connected span. asterisk/full.1:Apr 24 01:15:25 VERBOSE[4196]

Im having a problem getting the 2 cards working together. I added the TDM with 3 FXO and 1 FXS board. The TE405p is working fine. THe TDM registers and identifies the FXO's and FXS but cant get them to go off hook. I hope someone can help. Asterisk seems to THINK its dialing it sends manager status as dialing, and it just sits there with no tones, on the phone dialing out. If I dial,

Hi, I've been trying to get my zaptel x100p cards working for the past week now. this is what I've done: installed asterisk: make clean make linux 26 (for fedora core 2) make install installed zaptel: make clean make make install did a modprobe zaptel, and wcfxo got this in /var/log/messages: PCI: found IRQ 11 for device 0000:00:0f.0 wcfxo: daa mode is 'FCC' found a