similar to: TDM400P-04B fails after reboot

Hello all. I have here a TE110P (configured as E1) and a TDM400P (with four X100P - FXS). Both boards are recognized by the operating system as showed above: 0000:08:00.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device b1d9:0003 Flags: bus master, medium devsel, latency 64, IRQ 169 I/O ports at e800 [size=256]

In my attempt to setup a single FXS line I have been following the instructions for "Telephony Card Drivers" on the asteriskdocs.org site. I have managed to checkout, make and install the zaptel code and can load the zaptel module but when I attempt to load the wcfxs module it tells me: ZT_CHANCONFIG failed on channel 1: No such device or address (6) FATAL: Error running install

I think I have a bad FXS module on my TDM400P. Channel map: >> >> Channel 01: FXO Kewlstart (Default) (Slaves: 01) >> Channel 02: FXS Kewlstart (Default) (Slaves: 02) >> >> 2 channels configured. >> ZT_CHANCONFIG failed on channel 1: No such device or address (6) The zaptel loads ok, but the wctdm reports No such device or address and stays loaded. The

I've got the latest zaptel and cvs asterisk software loaded on my phone server running FC3. And yes, It's fully updated and udev is setup correctly. I've got a TDM400P with one FXS and one FXO module installed. When I load zaptel and wctdm and run ztcfg -vvv, I get this: [root@asterisk ~]# ztcfg -vvv ZT_CHANCONFIG failed on channel 1: No such device or address (6) Zaptel

Hello I setup Asterisk@Home with purely VoIP and it worked fine. I then added an X100P card so I could call out / take inbound calls via PSTN and that went fine. But I have just added a TDM400P card (specifically a TDM30B) and now problems. Here is some of the output. Any ideas on what I should be looking at next? When I run genzaptelconf -s -d I get lots of erors on screen - bit I can

Hi there my zaptel hardware is giving errors while loading but they seem to load just fine. the lights wil work and my wctdm card is also workin and the isdn works to But when I stop asterisk I have to reload al cards again is this normal? This is my zaptel.conf is there no way to group these because my te110p is giving an error that it can't find channel 35 but 35 belongs to my wctdm.

Hi when I turn on my PC I able to load the drivers and start my card, if I reboot the PC I have the following error ztcfg -vvv Zaptel Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) Channel 03: FXS Kewlstart (Default) (Slaves: 03) Channel 04: FXS Kewlstart (Default) (Slaves: 04) 4 channels

Hmm, I don't have /etc/modprobe.conf, and wctdm is giving me problems. Which device is it talking about? [root@asterix /]# modprobe wctdm /lib/modules/2.4.20-8/misc/wctdm.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg

Hi My card is working, but when I reboot the machine, most of the times it is not working, I get "ztcfg: ZT_CHANCONFIG failed on channel 1: No such device or address (6)" To make it work again I have to shut down, remove the card, reboot so kudzu will remove the config. shut down again, put the card back in, reboot, now kudzu see it, I choose "Ignore" and then it's

Hi, I'm having problems using a TDM400P Card. I put my SIM card in a Nokia Premicell and connected it to a TDM400P card but when I make calls to the number, it hangs up automatically. The card also can't call out. Any ideas? I've searched the archives without much success. I appreciate all your help. Details: I'm using Asterisk 1.2.17 on Fedora Core release 5 (Bordeaux). On an

Hi, I just got my TDM400P card (2 modules) and i installed it no probs. The card is detected fine, but for some reason when I add the card to zaptel.conf i get the following error: --snip-- ZT_CHANCONFIG failed on channel 2: Invalid argument (22) Did you forget that FXS interfaces are configured with FXO signalling and that FXO interfaces use FXS signalling? --snip-- My /etc/zaptel.conf looks

Hi, I have a running asterisk 1.2.1 (bristuffed) with a TDM400 Board. Connected to 1 port is am ordanary Fax Machine. Everything 'seems' to work, however receiving faxes is very unreliable. Sometimes I receive a normal page, without problems. Sometimes half of a page and the rest is scrambled, but most often, I receive nothing and the other site reports a Fax error... The Fax machine

Using asterisk 1.4.18 and zaptel 1.4.9 on x86_64, I am having trouble dialing out to the pstn. The call is initiated at Zap/1-1 and should exit via Zap/3. I get the following: -- Starting simple switch on 'Zap/1-1' -- Executing [2111 at internal:1] Dial("Zap/1-1", "Zap/3/8801234") in new stack [Feb 25 02:36:59] DEBUG[7194]: chan_zap.c:1954 zt_call: Dialing

Hi, I have a TDM400P running with only one FXO port running on a VIA EPIA MS10000 (1Ghz Via Eden). When I run zttest from Zaptel 1.2.1 it hang and when I interrupt it with Ctrl-C that is the result: ?anyone have some idea about why isn't working? Some additional info: # /usr/src/zaptel/zttest -v Opened pseudo zap interface, measuring accuracy... --- Results after 0 passes --- Best:

I have linux 2.6.5 running on my machine.I downloaded The latest version of Zaptel from the cvs repoistory.Compiled zaptel with the "make linux26" option. Installed it by modprobe which gave no errors.However when i did "modprobe wctdm" i got the following error. "FATAL: Module wctdm not found." I have no idea why it's happening.Tried Googling but got nothing.ANY

Hi all, I can't figure out why my TDM400P (with one FXO plugin) won't answer any calls. There are no messages in the Asterisk console when a call is placed to the FXO line from the PSTN. Any suggestions would be most appreciated. The wctdm and zaptel modules are loaded: [root@steerpike asterisk]# lsmod | grep wc wctdm 37952 0 zaptel 189700 1 wctdm

I have an Asterisk@Home 1.3 server (Asterisk 1.0.9) and recently added a TDM400P with (1) FXO card on port 4. Inbound calls are always successful but outbound calls fail 75% of the time with intercept messages from my dial tone provider that include "we're sorry, your call did not go through", and "we're sorry, when placing a local call it is now necessary to dial an area

I am having problems getting a Nicherons TDM400P wildcard clone to dial out. Everything appears to be configured correctly, but although I see call progress, it never seems to actually pick up the phone. (The following is a test of 911 emergency, where I substitute 811 [repair service] as the actual number dialed.) *CLI> -- Executing [911 at from-internal:1]

Greetings all, I'm new to asterisk... Finally got two IP phones and two TDM400P's (one with four FXO modules and one with four FXS modules)... Began experimenting a couple days ago and have ran into a very aggrevating problem. My system consists of the following hardware: Abit BL7-RAID motherboard Pentium 4 1.6GHz processor 512MB SDRAM 2 TDM400P cards 2 3Com 3c905

I have had a TDM400 with 2 FXO and 2 FXS working for ages (>12 months). It has stopped working. All four green lights are still lit. I have rebuilt zaptel and asterisk and restarted but the problem persists. /sbin/ztcfg -vvvv Zaptel Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Slaves: 01) Channel 02: FXO Kewlstart (Default) (Slaves: 02) Channel 03: