similar to: QuadBRI: How to set the outgoing callerid (KPN - NL)

Most of the time i can find answers to my questions on the wiki, google, or searching the list now i am stuck . I have a small * box at my house running 1.0.9 stable and a devlite kit. Every thing is awesome VM, IVR, Echo canceling, and Meetme are all working great. But on Incoming caller id i need to add a 9 as a prefix to make it easier to return call from my cordless phone (cheap vtech

Hi list, Hopefully, some of our Dutch members can help with this one. I'm also based in the Netherlands and am using a Sipura (Linksys) SPA-3000 (firmware v3.1.10(GWd)) as a PSTN to VoIP gateway for my Asterisk test system. It works fine, except that the Called ID (CID) is not working. I'm aware that KPN (our local telco) requires a separate subscription to activate CID on POTS

Hi, I'm using a ISDN-30 E1 line from KPN Belgium. The challenge is to get a correct CallerID on outgoing lines. When I put this in my dialplan: exten => _0.,1,Set(TEMPVAR=${CALLERID(num):1}) exten => _0.,2,Set(CALLERID(num)=144622${TEMPVAR}) exten => _0.,3,NoOp(${CALLERID(num)}) exten => _0.,4,Dial(Zap/g1/${EXTEN:1},,) The resulting CallerID is accepted by the telco, but on

Hi list! I am installing an * box that will be installed on a site with KPN BRI ISDN in The Netherlands. I am using bristuff fron Junghanns. Does anybody know the correct settings for this? I will not have internet access there which makes it harder to google around on location. switchtype = euroisdn is pretty obvious but what about these settings: signalling = bri_cpe_ptmp ; p2p TE mode

Hi All ... I'm running Asterisk 1.2.13-BRIstuffed-0.3.0-PRE-1v which has a Junghanns QuadBri card in it (lspci reports Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01)) I have a regular KPN ISDN2 Line connected which works fine with the the zapata.conf below. However, I also have a new KPN ISDN Mutli (meervoudig) line (PBAX-Group), which works fine for incoming calls,

Hello all, Recently I migrated all telephony in my house to asterisk thanks to the Asterisk, QuadBRI which works wonderfully well. Some small tweaks to make but that's on the long list. On the short list is the ability to reliable send and receive SMS. For SMS I already built a script email2sms, but sometimes the SMS doesn't get send from some reason, the sms log then reports something

Hi list, I have a server running a simple hfs isdn card running with chan_misdn. the problem is, I can't get asterisk to pick up the phone, outgoing calls work fine. when running asterisk with -vvvvvvvvvvvc I get the following "log" when I try to dial the isdn server. P[ 1] * Starting Ast ctx:kpn-in dad:0594643637 oad:0878722291 with 's' extension P[ 1] MGMT: SSTATUS:

Hello, I would like to put 1 asterisk box in Country A and 1 asterisk box in Country B. Let's assume : - Asterisk box in country A = GWA - Asterisk box in country B = GWB - Calling party number (located in country A) = CgPNA - Called party number (located in country B) = CdPNB - Second Called party number (located in country B) = sCdPNB - PSTN in country A = PSTNA - PSTN in country B = PSTNB

Hey, anyone know if it's possible to receive faxes through a Junghanns bristuff quadbri card? In germany, currently I have faxes coming in on DID line into QuadBRI and then passing to Digium TDM400 (analog) and into faxmachine. But the reliability of TDM card is spotty, so I want to maybe just accept faxes in on ISDN card and save on asterisk system ...? keeping digital signal strong ...

Hi everybody I hope that somebody can help me with the following .... I have 2 quadbri cards 2 - 1t0 cards 1 pabx alcatel 4200 I would like to connect my asterisk to the alcatel , I installed bristuff 0.3.0-1p , loaded the zaphfc driver in NT mode configured zaptel and zapata , it works great. then I removed the 1 t0 card, added the quadbri loaded qozap : insmod qozap.ko ports=15 ( 4 ports

Hello, Is anybody there using quadBRI form Junghanns.net with Asterisk ? I would like to order that card but first would like to hear some opinions. Thank you in advance Bartosz

Hello, I have bought a targeta quadbri. I want to realize a PBX server to send and to receive fax on lines BRI. I have installed asterisk and the drivers of quadbri (bristuff_0.2.0-RC7b). I downloaded and installed the module spandsp-0.0.2pre10 When i send a fax from the fax machine to asterisk, the application rx_fax saves the fax in a file on the hard disk. The problem comes when I try to send a

Hello, We have a quadBRI in NT mode with bri_cpe_ptmp signalling and when connect a ISDN telephone to this nothings happen. What can I do? My config files are this: Zaptel.conf: loadzone=es defaultzone=es # qozap span definitions # most of the values should be bogus because we are not really zaptel span=1,1,3,ccs,ami span=2,1,3,ccs,ami span=3,1,3,ccs,ami span=4,1,3,ccs,ami bchan=1,2 dchan=3

Hi, I have an asterisk box with a QuadBRI. I am close to make it work like I want: Incoming calls to SIP are OK, outgoing calls are quiet working thanks to Michael Sandee advices. My real problem is that my * box is freezing very often when I probe qozap (bri-stuff 0.0.2). I have tried two distribs (Debian Kernel 2.6, Mandrake 9.1 Kernel 2.4) and it always work for a few minutes and freezes. At

I have a problem with Asterisk-bristuffed using a zaphfc card. I am located in the Netherlands, so I have an ISDN line from KPN. When I start Asterisk, and plug in the ISDN line, everything works perfectly for about 5 minutes. And then the ISDN line is down for 1 minute, and after that minute, the line comes back up and works for another 5 minutes. Every time the line goes down I get the error

Hi, I'm trying to connect quadbri between powered ISDN phone and ISDN line: ISDN <---1---> TE - * - NT <--2--> Phone I use quadbri, suse 9.2 and latest 0.2.0-RC7k bristuff. I've used sample settings provided with package, but do get strange error (I think that I have wrong setting for P2P or P2MP setting and cables 1 and 2). If I connect phone to ISDN with straight cable

Hi, I'll soon replace a Junghanns OctoBRI with a Junghanns QuadBRI. As both use wcb4xxp driver (dahdi 2.3.0, libpri 1.4.10.2 and asterisk 1.6.1), I'm planning to proceed this way : 1. Edit 2 versions of files /etc/dahdi/system.conf and /etc/asterisk/dahdi-channels.conf (one for each card). 2. Link current system.conf and dahdi-channels.conf to QuadBRI files. 3. Power PC off 4. Swap cards

I am unable to make quadbri board to work in NT mode, in TE mode it works OK. I have set 5 jumpers to NT mode. Dmesg shows everything OK: qozap: Junghanns.NET quadBRI card configured at mem 0xd084e000 IRQ 9 HZ 100 CardID 1 qozap: S/T ports: 4 [ TE TE TE NT ] qozap: 1 multiBRI card(s) in this box, 4 BRI ports total. from Asterisk side seems to be ok. pri show span 4 Primary D-channel: 12 Status:

Hi to all, I have a question about the callerid (msn number) off calls comming FROM a queue. This is my setup: - ISDN using zap (zaphfc) - Incomming calls arrive in a queue - One of the members of the queue is my cell phone... member => Zap/g1/XXX73XX19 (X to protect my privacy ;-)) The problem is the call from the queue to my cell phone. In a dailplan i can set the outgoing msn using

Morning Asterikians, I've just got my nice shiny quadBRI card, and it seems to be working very well - except for one little issue - CallerID. The card is currently connected to an ISDN2e line in P2P mode, and an S0 adapter on our existing alcatel PBX. The S0 connection recieves callerID and displays it correctly - the 2e line doesn't, and BT have said that CLID was enabled on the