similar to: Multiple Digium cards?

Hi I am interested in setting up an Asterisk PBX in my office with digium hardware, and I just have a few questions in regards to what I would need. It is my understanding that an FXO card is used to interface with an incoming/outgoing phone line, and an FXS card is used for interfacing with a phone within the system. Currently we have 4 incoming/outgoing phone lines and would like to have

I'm installing my first Asterisk server. I have a TDM04B card installed in my asterisk server (4x FXO ports). I have 5 Cisco IP phone 7960 working fine on asterisk using SIP. My configuration to receive call is working as expected meaning anyone calling on one of the 4 FXO ports is answer by asterisk and asked to enter the extension of the person to reach and then it is transfer on the

Hello, I am having problems configuring a TDM400P 4 Port FXO card with groundstart signalling. The box has 2 X100P's, 1 TDM04B and 1 TDM40B. I can configure it for loopstart and it works, just not groundstart, which I need for this installation. What am I missing? Thanks! Mark /etc/zaptel.conf #two X100P FXO Cards # fxsls=1-2 # TDM400P 4 Port FXO (TDM04B) fxsgs=3-6 # TDM400P 4 Port

Hello all. My company currently has an older Executone PBX system that we are outgrowing. Rather than wait until the last minute to make a hasty decision, I thought it would be a good idea to do some research and compare options first. My expertise is in computers and networking, and telephony systems are mostly foreign to me. What we currently have are 5 incoming POTS lines and 25

Hi, I've been lurking here for about a month and I've been putting together our companies planned migration to a new office and a new phone system. Could anybody tell me if there are any pitfalls to the following setup I may have missed? 1: TBD PC running * a: Digium TDM04b FXO connected to PSTN 1: lines rolling over via SBC sentrex to get multi-lines on 1 number b: Digium

I know, I know, check the archives but I can't find an answer since the new cards are well, NEW! I understand the whole issue of expandability and flexibility of using a T1 card and an Adtran 750. FXO or FXS, you mix and match. With the new card offerings from Digium I can easily put a 4CO by 8 Station system together. Barring the extra interrupts, extra CPU Cycles of extra interfaces, is

Hi: I have one TDM40B and one TDM04B on my Asterisk box. Both were working fine. Then, all of the FXS ports started to make echo sounds when I make FXS to IAX or SIP connection. All of the FXS ports fail to make bridging to the FXO channels. And when I try to make a call from the console to the FXO ports, I only hear static noise. Any suggestions about the source of the sudden change in

Hi, I've read through the Asterisk handbook and I'd just like clarification from someone that's implemented the above before. Lets imagine I want to use the CallingCard application and don't want to tell a client to buy a channelbank (the analog extensions are too many to connect to FXS cards), I figure I could set them up as below: Original Existing Setup

I am having a problem with a couple servers. They both have a Digium TE110P and a TDM04B card. I have setup the system so the TE110P uses channels 1-31 and the TDM04B 32-35. The problem is that when we reboot the server sometimes the TDM04B is recognized first and the TE110P second so the configuration fails. I do not know why this happens and to solve this I have to do a "service

I have a client who wants a Meetme box with 12 FXO ports, to connect to Analogue lines coming from an Ericsson PBX. It looks like I could do this with four different hardware configurations: a) three TDM04B cards (based on TDM400P) b) one TDM04B and one TDM808B c) one TDM804B (or TDM854B?) and one TDP808B d) one TDM2403B (half filled TDM2400P) Apart from considerations of cost and PCI slot

Hi, I have some problem to get this setup working. I have a CAC Channel Banl I, with FXO and an Asterisk box ( I am using Asterisk@Home 1.2) and I have a TE110p installed in this box. What I want to do is, just to be able to dial one of those lines that already are connected to the channel bank, and transfer that call through TE110p and Asterisk to a user agent somewhere through Internet.

Hi folks, I've already searched the mailing list but no one else seems to have my same problem. I'm using Asterisk with the following configuration: Fedora Core 4 (but I also tried Fedora 3) 1 Digium TE110P 1 TDM40B 1 HFC-S 'Cologne' bristuff 0.2.0-RC8o (zaptel 1.0.9.2) I compiled right, I can load kernel modules but when I try to unload wcte11xp module (the one

This might be a newbie question but I'm just wondering how would it be possible to have 30 analog lines using asterisk for PBX by just using TDM40B and X100P (or are there any device>), if an ordinary PC support just 4 PCI slots? the maximum scale i guess would just be 2 x 8. Adding a new PC just for this purpose would be costly. I would appreciate your comments. Thanks.

Hi. Am new to this concept but have been requested to add VOIP capability to a small office phone system. They currently have 4 standard analog lines running into a PBX feeding 16 phones, with all the usual features, call transfer call hold internal calls etc. would the following seem reasonable ? asterisk server:- ( what specs ) cat5 > broadband (VOIP) 4 FXO's for incoming PSTN

Hi, I am building for a customer an * solution that will use 2 Digium cards. 1 x TE110P (T1 ISDN PRI) 1 x TDM40B (4 analog ports, 2 for faxes, 2 for extensions) The system will be connected to the PSTN through the T1 ISDN PRI interface. All customer extensions will be SIP phones except 2 fax machines that will use the analog FXS ports on the TDM40B card. I have been investigating on this

Hi everyone I have a Digium card TE110P and after plug it, turn on the computer and configure, the LEDs don't light up in spite of what Digium FAQ says about the LEDs: When will the LED's light up on my TDM400P/TE110P/TE2XXP/TE4XXP? ... The TE110P LED's will light up RED when the span is configured and kernel module is loaded. If configured correctly and a circuit or channel bank is

Hi All, I Have a Digium Card TDM40P, the specification say: OEM TDM40B: TDM400P + 4 PORT FXS Bundle, my question is: Can I to install analog lines of PTSN?, other detail is: this card have 4 card green. I need to know what is the best card for the following scenario: I need a IVR for my comapny and a PBX, but i want that my extension not use FXS I want IP phone . Thanks ins advanced,

Has anyone used ground start on Asterisk? I am using a TE110P connected a Adtran 750 channel bank FXO card. It appears that Asterisk is not setting the CAS RBS bits properly to seize the line. I can see this with the zttool and the Adtran admin serial port status. I have configured the zaptel.conf and Zapata.conf to use fxsgs on those channels. Syed Akbar Alico Systems Inc www.alicosystems.com

I have been searching for a while and can't find anything specific like this. Here's is my setup: IAXy -- broadband network -- Asterisk -- TE110P -- Channel Bank -- POTS lines (FXO) Everything works fine except for the echo at the IAXy. There is no echo on the POTS end, so Asterisk is doing a good job of echo canceling. Is there any provisioning in the IAXy to do echo

Hi Folks, Does anybody have experiences with plugging 3 TDM400P cards in one PC?? I think about a Asterisk box handling 8 incoming analogue lines and providing 4 lines to an old analogue PBX. I read a lot about trouble with the TDM400P cards so this idea seams to be not really god, or? Ciao Joerg -- _____________________ Don't PANIC