similar to: Polycom IP-500 & 600 Nat settings.

Hi, Has anyone used polycom phone IP500/600's conference feature? I ran into some issues. Polycom is not behind NAT. Polycom calls pstn number A, (gets two way voice), presses conference, (A is put on hold), calls pstn number B, (gets two way voice), presses conference again, suppose to have all three parties in the call, polycom and B have two way voice, but polycom doesn't have two

I am in the process of setting up an * system using Polycom IP 500's. I don't want to spend time setting a ftp server for application and configuration files at the moment, just want to use the web interface to the Polycoms. DCHP works OK and IP is obtained correctly. Polycom fails to load .cfg file and holts. I have read the 143 page admin user guide a couple of times...and I missing

I know the Polycoms work with NAT, but you have to specify the public IP. Is there anyway for it to discover the external IP automatically? I like the phones (been playing with a 301) but for some of our clients who have a dynamic IP (and no hope of getting a static ie cable or residential DSL) I'd be afraid to use them since you have to specify the IP. What about the Cisco phones?

I?ve been tearing my hair out trying to get a Polycom phone (behind a NAT) to register to an * box behind a Cisco SIP ALG. With known good credentials configured on the phone and in *, I get 403 Bad Auth when trying to register. If I put the phone onto the same LAN as * it works fine without changing any authentication parameters whatsoever. If I make the secret blank (null) on the phone and *,

I am getting ready to install Asterisk and I was looking into the Polycom IP600 phones. I spoke with Polycom sales to verify the multiple line appearance and they said it would work. More specifically, if lines 1-3 all contain the same SIP registration info, the Polycom will only send out 1 SIP registration to the server and then handle the calls ringing on multiple lines. I was wondering if

I am getting to my wits end with these phones (and so is my boss). I am getting an random echo on these phones and I have an issue opened with Polycom and its been in their research and development department for almost a month with no results. I have noticed that I get a message "RFC3389 support incomplete. Turn off on client if possible" in asterisk. I have researched this and made

Do the Polycom IP phones have some programmability so you can do some programmable phone buttons like you can on the Cisco phones? If there is programmability, such as for soft-keys and the like, how would you rate Polycom's vs Cisco's capabilities? And where can one find the programming documentation? Thanx. Ray. -- Scanned for viruses and dangerous content at

Hello all, I need the bootrom.ld file to set up some Polycoms I have Platform: Model=SoundPoint IP 330, Assembly=2345-12200-001 Rev=A I've publiched on my FTP files downloaded from http://support.polycom.com/PolycomService/support/us/support/voice/soundpoint_ip/soundpoint_ip330_320.html (3.2.3 combined and split zips) but my phones are still showing the message: "error, application is

Andrei, Do you have X-Windows running on the linux box? I had a similar issue that was eliminated when I stopped this process and samba from running. Now samba is only allowed to come up during non-business hours, for changing BG music. Also, make sure your registration period in either (polycom) ipmd.cfg or sip.cfg is set to be at least the default 3600 time period. I also removed the

Has anyone been able to get the minibrowser on the Polycom SoundPoint IP 500/600 phones working? If so could you share the relevant sections of your config with me?

Hello All, I am wondering if there is a way to make Polycom IP 500 SIP phone display digits dialed after a call is connected. For example, when I call an IVR, after the connection is complete, the digits dialed to enter account number etc are not displayed on the phone. They are sent to the target. My users are asking to see the digits dialed as they are used to seeing them on our old Nortel

We recently took a few Polycom Soundpoint IP 500 to test out in Asterisk environment. So far it has been good. Call Hold, Transfer, DMTF etc. However, I do notice every now and then the Polycom fails to register with Asterisk. Asterisk console outputs the following: Feb 3 13:02:32 WARNING[278546]: chan_sip.c:2365 __transmit_response: Unable to determine sequence number from '' Feb 3

hello all, I'm having problems getting my polycom soundpoint ip 500 working, and was wondering if anyone would be willing to share their config files with me (the polycom configs). I have managed to get my boot server up and running, and the phone successfully updated its ROM, and downloaded the config files i have put together for it (the display shows correctly but the line won't

Hi all, I have a Polycom Soundpoint IP 600 that looks like it is fried. It either has a bad or corrupt bootrom (I'm guessing). It never gets to the prompt that asks if I want to enter the setup configuration or continue booting. When plugged into power, it turns on, shows the Polycom logo for 3 seconds and then pretty much goes dead with two red lights on. The one in the top right corner

Hello All, I have Polycom IP 500 phones which I would like to have message waiting indicators on. So far, I have my system running well but the problem I am seeing is that MWI doesn't seem to tell my phone that it should display a MWI state. The light does not show when you have message nor is there any indicator on the text lines of a message waiting. The wiki doesn't cover this

i'm trying to set up outboud caller ID on 3 polycom ip 500 phones. here is how i have them set up. each phone is using 2 lines, all registered to * phone 1 line 1 is registered using the DID, and the next 5 lines reg to 03152 03153 03154 03155 03156 from my understanding, the way the polycom configs are set, i have to put the 03152 in the reg.x.address field. and it seems that is where

Hi, everyone, We've been reasonably happy with Polycom SoundPoint phones, but we only have them installed on the LAN. I've read that they have problems working across NAT. So ... I guess I have a few questions. First, is there a way to get Polycoms to work well over NAT? If not, then are there phones of comparable voice quality that do work well over NAT? Without costing a lot more?

Hello, I just wiped out my old asterisk install and installed Asterisk at Home. I was quickly able to get my Digium TDM422P working, 2 POTS lines, 2 phones. I also got X-Lite working as a SIP extension. I then tried to setup my Polycom IP 500, and this was not so easy... Using AMP I created SIP extension 205 to be used with my Polycom phone. I setup username = 205, secret = 123, context =

Hello, After receiving and finally being able to configure my new Polycom IP 600 phone Here are my initial experiences: GOOD STUFF: - The sound is wonderful from both handset and speaker (711U) - The large multi-shade LCD screen is beautiful (for a phone) - The phone has an integrated Ethernet switch so you can connect a PC to it as a passthru - The AC adapter was included (small thing, but

I have sent a Polycom IP500 phone to an overseas remote user who has a Speedtouch adsl modem/router. The phone is connected to the 4 port router which performs NAT for the network. The phone rboots, find the server, downloads it's config and tried to register. Then it immediately becomes UNREACHABLE. Jul 26 17:44:41 NOTICE[21026]: chan_sip.c:9138 handle_request_register: Registration from